• Panasonic TV-42Z90BEB - A Partial Review

    From Java Jive@java@evij.com.invalid to uk.tech.digital-tv on Wed Oct 21 18:52:11 2026
    From Newsgroup: uk.tech.digital-tv

    So far, I have this connected to the internet via my home network, an
    aerial, and am in the planning stage for a satellite dish, but am
    getting so angry that I thought I'd give a review thus far, if only as a public warning.

    First, the hardware itself seems pretty good ...

    The screen is what I really bought it for. It's a personal opinion of
    course and others may choose to disagree, but it's easily the best
    picture on any TV that I've seen close up. Full HD programmes like Attenborough's "Africa" look spectacular and wonderful, almost
    breathtakingly so.

    The connections it has are as follows:

    A standard UK TV Aerial connection, nothing further to add about that.

    A Common Interface and two Sat female F-connectors, but the latter only support DiSEqC 1.0, so can switch between different LNBs, but cannot
    work a rotor. If you want one of those, you'll have to buy an
    appropriate receiver with DiSEqC 1.3/USALS. As I haven't yet set up a
    dish, the problem being that there is nowhere convenient to put it where neither will it be in the way nor something else in the way of it, I
    cannot comment further.

    A Fast Ethernet connection - 30 years on I really think it ought to
    have Gigabit Ethernet, but the former will do for streaming.

    4 x HDMI, 2 rated at 4K144Hz, one of which supports eARC/ARC.

    3 x USB, one rated to support a hard disk.

    Digital audio SPDIF and analogue audio outputs.

    It's Fire OS that rather lets it all down. Sometimes it's just plain confusing, at others just plain illogical, at still others doesn't work
    as advertised, and all the time sandblasts the user with bloatware that
    gets in the way of everything else. In particular, Freely doesn't seem
    to work at all.

    FTR, it's running:

    Fire OS: 8.1.8.0 (RS8180/3745)
    Home version: 7300127.1

    When initially setting up, there are several parameters which alter its subsequent behaviour:
    1) Whether an antenna and/or satellite source is connected;
    2) Whether you allow it to enable the ethernet or WiFi connection;
    3) If (2), whether you allow it to connect to your Amazon account.

    If an aerial is connected, the antenna channels will scan successfully;
    I presume it would be similar with a satellite connection. After this,
    the channel listing is quite dense, with few or no channels which are
    not broadcasting.

    However, after that is completed, things depend on whether (2) and/or
    (3) were enabled at the start.

    If neither, shortly after the antenna scan finishes, a cut down Home
    screen appears (if only the connected one could be so refreshingly free
    of bloat). Unfortunately it has an error message on it ...

    Home Screen is Currently Unavailable
    An internal error has occurred. Try refreshing the page to see if
    that resolves the problem. If the problem persists, please contact
    Amazon customer service.

    ... but IMO displaying this message is itself an error, all that's
    happened is the user has chosen not to connect his TV to the internet
    and his/her Amazon account. That is their choice to make, so an error
    message should not appear. In this situation there are no apps, so no
    Freely.

    If you choose (2) - connect to the internet but not your Amazon
    account - after scanning the antenna channels the system shows a
    message ...
    Live TV - Scanning for Channels ...
    Automatic Channel Listings
    Please wait.
    ... which is displayed for so long that one is inclined to suppose that
    the process is hung, as indeed on occasions it has been (for reasons
    that will become apparent I've tried this several times - I'm not
    quite sure exactly what causes it to hang at this point, but I think it
    was when I didn't allow an ethernet connection and had no antenna
    plugged in). If actually it's not hung, about half way through this
    message being displayed it asks for your postcode.

    At the end it displays the same message as it does when you press Freely
    on the remote:

    "Install Freely on your TV ... providers in the UK - all for free
    Install/Cancel"
    Select 'Install'.
    "Operator App Installation
    Search and install available Operator Apps ...
    No supported Operator App found.
    Confirm"
    Select 'Confirm'.

    So clearly the TV now thinks it should have Freely, but it doesn't. See below.

    The Channel List is now sparse, adulterated with an exasperating number
    of blank channels, and the Home screen is still the cut down one
    displaying the above error message. Again, there are no apps/Freely.

    If you choose (3) - connect to the internet and your Amazon account -
    after scanning the antenna channels the system shows the same messages described above, and afterwards you have everything above + Fire TV but
    still no Freely, it's not even listed as present under:
    Settings, Applications, Manage Installed Applications

    The Home screen is now the Fire TV Home screen and is cripplingly
    encumbered by a load of categories and options which I will never want,
    none of which junk can be removed. Indeed the only customisations
    possible appear to be reordering the Apps in their own particular
    section of it. Navigating it is rather like playing Minesweeper. As
    ever, bloatware rules, and you just can't see the wood for the trees.

    I think things need to be said about the Antenna channel list, which by default (2 or 3) gives a list of channels most of which are blank,
    because they're for other regions. How is it that the antenna list,
    note antenna list, not a general list, is now populated with channels my antenna cannot receive? I have not been able to find any option to
    simplify things by automatically hiding empty channels, which makes it virtually compulsory to create a favourites list, to avoid scrolling
    past a long, long list mostly consisting of empty channels, but this in
    itself is a wearisome process, because every time you land on a new
    channel, it can take several seconds before its content, if any, can be
    seen and/or heard to show you that it's worth adding to the list. Hence scrolling through it allowing up to 10s or more for each channel to
    respond, but often not getting a response, takes a long time.

    I can not comment knowledgeably about its behaviour with satellite
    sources, but I'm guessing it would be as bad or worse.

    So back 'Freely', which doesn't seem to work at all. On this TV
    'Freely' is supposedly installed as a System App, not an Operator or
    User App, but some aspects of the OS have not been updated accordingly,
    for example the message at the end of scanning clearly show an
    expectation that it should be installable as a Operator or User app, but official documentation suggests that it's not. If I go into
    'Applications' in the configuration options, Freely is not listed as
    being installed. If I go into 'Live TV' in the configuration options,
    there is an option 'Manage Channels - 123 Channels', but if I choose
    this, the only option is 'Prime', to which I'm not subscribed. If I go
    into the Amazon App Store and search for 'free', 'freely tv' is listed
    as a result, but choosing it leads only to a repeat of the rigmarole
    from pressing the 'Freely' button on the remote. I've also tried
    sending it to my TV from the Amazon store, but the result is always the
    same. The whole thing seems to be a mucking fuddle.

    So instead I've had to download and install all the individual player
    apps. Thankfully, at least all of them work:
    BBC IPlayer
    BBC Sounds
    ITVx
    STV Player
    Channel 4 Player
    5 Player

    I've also installed CxFileExplorer. The advantage of which is that it
    enables you to browse other computers on your LAN directly over the
    network, without having to suffer all the hassle of using DLNA or
    needing an external box to do it. It's not available from the Amazon
    store, but you can install it from the APK file using the Downloader
    app, instructions for doing which can be found online - basically you
    have to enable Developer Options and use then to enable Downloader to
    install 'alien' apps. Also, you have to install the most recent version
    BUT ONE, as the most recent won't install for some reason.

    I've also installed the YouTube app, but unless I can install something
    like uBlock Origin as well, I won't be using it because of the number of advertisements is way OTT.

    Great screen, but it's a great pity about the software.
    --

    Fake news kills!

    I may be contacted via the contact address given on my website: www.macfh.co.uk
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Woody@harrogate3@ntlworld.com to uk.tech.digital-tv on Wed Oct 21 19:39:16 2026
    From Newsgroup: uk.tech.digital-tv

    On Wed 21/10/2026 18:52, Java Jive wrote:
    So far, I have this connected to the internet via my home network, an aerial, and am in the planning stage for a satellite dish, but am
    getting so angry that I thought I'd give a review thus far, if only as a public warning.

    First, the hardware itself seems pretty good ...

    The screen is what I really bought it for.-a It's a personal opinion of course and others may choose to disagree, but it's easily the best
    picture on any TV that I've seen close up.-a Full HD programmes like Attenborough's "Africa" look spectacular and wonderful, almost breathtakingly so.

    The connections it has are as follows:

    A standard UK TV Aerial connection, nothing further to add about that.

    A Common Interface and two Sat female F-connectors, but the latter only support DiSEqC 1.0, so can switch between different LNBs, but cannot
    work a rotor.-a If you want one of those, you'll have to buy an
    appropriate receiver with DiSEqC 1.3/USALS.-a As I haven't yet set up a dish, the problem being that there is nowhere convenient to put it where neither will it be in the way nor something else in the way of it, I
    cannot comment further.

    A Fast Ethernet connection-a --a 30 years on I really think it ought to
    have Gigabit Ethernet, but the former will do for streaming.

    4 x HDMI, 2 rated at 4K144Hz, one of which supports eARC/ARC.

    3 x USB, one rated to support a hard disk.

    Digital audio SPDIF and analogue audio outputs.

    It's Fire OS that rather lets it all down.-a Sometimes it's just plain confusing, at others just plain illogical, at still others doesn't work
    as advertised, and all the time sandblasts the user with bloatware that
    gets in the way of everything else.-a In particular, Freely doesn't seem
    to work at all.

    FTR, it's running:

    -a Fire OS:-a-a-a-a-a-a 8.1.8.0 (RS8180/3745)
    -a Home version:-a 7300127.1

    When initially setting up, there are several parameters which alter its subsequent behaviour:
    -a-a-a 1)-a Whether an antenna and/or satellite source is connected;
    -a-a-a 2)-a Whether you allow it to enable the ethernet or WiFi connection;
    -a-a-a 3)-a If (2), whether you allow it to connect to your Amazon account.

    If an aerial is connected, the antenna channels will scan successfully;
    I presume it would be similar with a satellite connection.-a After this,
    the channel listing is quite dense, with few or no channels which are
    not broadcasting.

    However, after that is completed, things depend on whether (2) and/or
    (3) were enabled at the start.

    If neither, shortly after the antenna scan finishes, a cut down Home
    screen appears (if only the connected one could be so refreshingly free
    of bloat).-a Unfortunately it has an error message on it ...

    -a-a-a Home Screen is Currently Unavailable
    -a-a-a An internal error has occurred.-a Try refreshing the page to see if that resolves the problem.-a If the problem persists, please contact
    Amazon customer service.

    ... but IMO displaying this message is itself an error, all that's
    happened is the user has chosen not to connect his TV to the internet
    and his/her Amazon account.-a That is their choice to make, so an error message should not appear.-a In this situation there are no apps, so no Freely.

    If you choose (2)-a --a connect to the internet but not your Amazon account-a --a after scanning the antenna channels the system shows a
    message ...
    -a-a-a Live TV - Scanning for Channels ...
    -a-a-a-a-a-a-a-a-a-a-a-a-a Automatic Channel Listings
    -a-a-a-a-a-a-a-a-a-a-a-a-a Please wait.
    ... which is displayed for so long that one is inclined to suppose that
    the process is hung, as indeed on occasions it has been (for reasons
    that will become apparent I've tried this several times-a --a I'm not
    quite sure exactly what causes it to hang at this point, but I think it
    was when I didn't allow an ethernet connection and had no antenna
    plugged in).-a If actually it's not hung, about half way through this message being displayed it asks for your postcode.

    At the end it displays the same message as it does when you press Freely
    on the remote:

    -a-a-a "Install Freely on your TV ... providers in the UK - all for free
    -a-a-a Install/Cancel"
    Select 'Install'.
    -a-a-a "Operator App Installation
    -a-a-a Search and install available Operator Apps ...
    -a-a-a No supported Operator App found.
    -a-a-a Confirm"
    Select 'Confirm'.

    So clearly the TV now thinks it should have Freely, but it doesn't.-a See below.

    The Channel List is now sparse, adulterated with an exasperating number
    of blank channels, and the Home screen is still the cut down one
    displaying the above error message.-a Again, there are no apps/Freely.

    If you choose (3)-a --a connect to the internet and your Amazon account-a -
    -aafter scanning the antenna channels the system shows the same messages described above, and afterwards you have everything above + Fire TV but still no Freely, it's not even listed as present under:
    -a-a-a Settings, Applications, Manage Installed Applications

    The Home screen is now the Fire TV Home screen and is cripplingly
    encumbered by a load of categories and options which I will never want,
    none of which junk can be removed.-a Indeed the only customisations
    possible appear to be reordering the Apps in their own particular
    section of it.-a Navigating it is rather like playing Minesweeper.-a As ever, bloatware rules, and you just can't see the wood for the trees.

    I think things need to be said about the Antenna channel list, which by default (2 or 3) gives a list of channels most of which are blank,
    because they're for other regions.-a How is it that the antenna list,
    note antenna list, not a general list, is now populated with channels my antenna cannot receive?-a I have not been able to find any option to simplify things by automatically hiding empty channels, which makes it virtually compulsory to create a favourites list, to avoid scrolling
    past a long, long list mostly consisting of empty channels, but this in itself is a wearisome process, because every time you land on a new
    channel, it can take several seconds before its content, if any, can be
    seen and/or heard to show you that it's worth adding to the list.-a Hence scrolling through it allowing up to 10s or more for each channel to
    respond, but often not getting a response, takes a long time.

    I can not comment knowledgeably about its behaviour with satellite
    sources, but I'm guessing it would be as bad or worse.

    So back 'Freely', which doesn't seem to work at all.-a On this TV
    'Freely' is supposedly installed as a System App, not an Operator or
    User App, but some aspects of the OS have not been updated accordingly,
    for example the message at the end of scanning clearly show an
    expectation that it should be installable as a Operator or User app, but official documentation suggests that it's not.-a If I go into
    'Applications' in the configuration options, Freely is not listed as
    being installed.-a If I go into 'Live TV' in the configuration options, there is an option 'Manage Channels - 123 Channels', but if I choose
    this, the only option is 'Prime', to which I'm not subscribed. If I go
    into the Amazon App Store and search for 'free', 'freely tv' is listed
    as a result, but choosing it leads only to a repeat of the rigmarole
    from pressing the 'Freely' button on the remote.-a I've also tried
    sending it to my TV from the Amazon store, but the result is always the same.-a The whole thing seems to be a mucking fuddle.

    So instead I've had to download and install all the individual player apps.-a Thankfully, at least all of them work:
    -a-a-a BBC IPlayer
    -a-a-a BBC Sounds
    -a-a-a ITVx
    -a-a-a STV Player
    -a-a-a Channel 4 Player
    -a-a-a 5 Player

    I've also installed CxFileExplorer.-a The advantage of which is that it enables you to browse other computers on your LAN directly over the
    network, without having to suffer all the hassle of using DLNA or
    needing an external box to do it.-a It's not available from the Amazon store, but you can install it from the APK file using the Downloader
    app, instructions for doing which can be found online-a --a basically you have to enable Developer Options and use then to enable Downloader to install 'alien' apps.-a Also, you have to install the most recent version BUT ONE, as the most recent won't install for some reason.

    I've also installed the YouTube app, but unless I can install something
    like uBlock Origin as well, I won't be using it because of the number of advertisements is way OTT.

    Great screen, but it's a great pity about the software.


    Funny that Charles. I got a Panasonic non-smart TV and it just would not
    work with some of the hybrid channels (Freeview 251-299). Most of these channels need an aerial connection for instructions where to find the
    channel you want and then attack the Interweb connection to find it (it
    did have an ethernet socket.)
    So I took it back (John Lewis fortunately who never said a word.)

    Then we got a Samsung smart TV which at first seemed good but it too has
    some idiosyncrasies and I'm a little unsure about the panel. However
    SWMBO likes it (bedroom TV) and now wired rather than wifi so....

    Finally we got a new TV for the lounge - this time a LG smart TV and
    that is a winner. Better panel, good sound, Freeview and Freesat, and it
    just works. However its a bit of a *** when you need to do anything as
    the setup/access screen is unnecessarily complex and cluttered, but
    having said that it I've rarely need to do anything with it.

    I just don't understand why there is need for so much 'up front'
    complexity. Both the Samsung and the LG have their own servers - Samsung
    TV Plus and LG Channels respectively - and there is no complex access,
    just dial up he channel number you want and it works!

    Ultimately the 28in Panasonic non-smart we have - on a shelf behind me
    as I type and which is now over a decade old - has by a country mile the
    best screen and sound.

    Drives you mad, don't it?
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Java Jive@java@evij.com.invalid to uk.tech.digital-tv on Thu Oct 22 02:11:51 2026
    From Newsgroup: uk.tech.digital-tv

    On 2026-10-21 19:39, Woody wrote:

    Ultimately the 28in Panasonic non-smart we have - on a shelf behind me
    as I type and which is now over a decade old - has by a country mile the best screen and sound.

    Yes, I've always had liked their displays.

    Drives you mad, don't it?

    Yes. These days every time you buy anything like this, there's always a
    hell of a struggle to get the interface into a usable form, or even as
    in my case to get the thing simply to work as advertised.

    I think most probably I'm going to have to find some way to reflash the firmware, but the Panasonic site said this is not possible from a USB
    stick, only via the internet. A while ago, when I had less detailed information about how the initial configuration gets set up, I had a
    chat session with them online, but had to leave because of a delivery at
    the end of the drive, and by the time I'd returned their chat software
    had timed out. I'll try to contact them again tomorrow to see what can
    be done.
    --

    Fake news kills!

    I may be contacted via the contact address given on my website: www.macfh.co.uk

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Jeff Layman@Jeff@invalid.invalid to uk.tech.digital-tv on Thu Oct 22 08:24:41 2026
    From Newsgroup: uk.tech.digital-tv

    On 22/10/2026 02:11, Java Jive wrote:
    On 2026-10-21 19:39, Woody wrote:

    Ultimately the 28in Panasonic non-smart we have - on a shelf behind me
    as I type and which is now over a decade old - has by a country mile the
    best screen and sound.

    Yes, I've always had liked their displays.

    Drives you mad, don't it?

    Yes. These days every time you buy anything like this, there's always a
    hell of a struggle to get the interface into a usable form, or even as
    in my case to get the thing simply to work as advertised.

    I think most probably I'm going to have to find some way to reflash the firmware, but the Panasonic site said this is not possible from a USB
    stick, only via the internet. A while ago, when I had less detailed information about how the initial configuration gets set up, I had a
    chat session with them online, but had to leave because of a delivery at
    the end of the drive, and by the time I'd returned their chat software
    had timed out. I'll try to contact them again tomorrow to see what can
    be done.

    I've only had Panasonic TVs for years, with the current one about seven
    years old. I understand that they no longer make them in Japan <https://www.slashgear.com/1846438/panasonic-tvs-who-makes-where-built/>.
    Does the back of the TV state where yours was made, JJ? Mine was made in Japan, but uses Firefox OS. It looks like Samsung and LG use their own Linux-based OS rather than Android, but I'm not exactly happy about
    privacy with those manufacturers. I'm not sure if I'm watching TV, or
    they're "watching me" watching TV if you see what I mean! Philips appear
    to use a range of OSs, but I've never really considered purchasing their
    TVs. Anyone here got a recent Philips TV?

    I expect that you've seen this thread: <https://www.avforums.com/threads/2025-panasonic-z90b-oled-tv-discussion-help-experiences.2532197/>

    I'm guessing that they now have no problem with "interrupted firmware updates", which may be why you don't have to bother with downloading to
    a USB stick first, checking that the download is ok, and then running
    the update from the USB stick.
    --
    Jeff
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Java Jive@java@evij.com.invalid to uk.tech.digital-tv on Thu Oct 22 11:06:52 2026
    From Newsgroup: uk.tech.digital-tv

    On 2026-10-22 08:24, Jeff Layman wrote:
    On 22/10/2026 02:11, Java Jive wrote:
    On 2026-10-21 19:39, Woody wrote:

    Ultimately the 28in Panasonic non-smart we have - on a shelf behind me
    as I type and which is now over a decade old - has by a country mile the >>> best screen and sound.

    Yes, I've always had liked their displays.

    Drives you mad, don't it?

    Yes.-a These days every time you buy anything like this, there's always a
    hell of a struggle to get the interface into a usable form, or even as
    in my case to get the thing simply to work as advertised.

    I think most probably I'm going to have to find some way to reflash the
    firmware, but the Panasonic site said this is not possible from a USB
    stick, only via the internet.-a A while ago, when I had less detailed
    information about how the initial configuration gets set up, I had a
    chat session with them online, but had to leave because of a delivery at
    the end of the drive, and by the time I'd returned their chat software
    had timed out.-a I'll try to contact them again tomorrow to see what can
    be done.

    I've only had Panasonic TVs for years, with the current one about seven years old. I understand that they no longer make them in Japan <https://www.slashgear.com/1846438/panasonic-tvs-who-makes-where-built/>. Does the back of the TV state where yours was made, JJ?

    Surprisingly, mine was made in Poland:

    <www.macfh.co.uk/Temp/TV-42Z90BEB_Label.png>

    Mine was made in Japan, but uses Firefox OS. It looks like Samsung and LG use their own Linux-based OS rather than Android, but I'm not exactly happy about privacy with those manufacturers. I'm not sure if I'm watching TV, or they're "watching me" watching TV if you see what I mean! Philips appear to use a range of OSs, but I've never really considered purchasing their TVs. Anyone here got a recent Philips TV?

    I expect that you've seen this thread: <https://www.avforums.com/threads/2025-panasonic-z90b-oled-tv-discussion-help-experiences.2532197/>

    I'd not seen that page, but had seen the UK firmware update page linked
    from there.

    <https://av.jpn.support.panasonic.com/support/global/cs/tv/download/fw/eu_2025/down_eu_uk_cis_02.html>

    I'm guessing that they now have no problem with "interrupted firmware updates", which may be why you don't have to bother with downloading to
    a USB stick first, checking that the download is ok, and then running
    the update from the USB stick.

    Yeahbut, what if a power cut crashes an update in such a way as to
    prevent internet access?

    A last ditch recovery method is needed, and I suspect that one exists,
    they just don't want to tell us about it.
    --

    Fake news kills!

    I may be contacted via the contact address given on my website: www.macfh.co.uk

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Woody@harrogate3@ntlworld.com to uk.tech.digital-tv on Thu Oct 22 13:52:59 2026
    From Newsgroup: uk.tech.digital-tv

    On Thu 22/10/2026 08:24, Jeff Layman wrote:
    On 22/10/2026 02:11, Java Jive wrote:
    On 2026-10-21 19:39, Woody wrote:

    Ultimately the 28in Panasonic non-smart we have - on a shelf behind me
    as I type and which is now over a decade old - has by a country mile the >>> best screen and sound.

    Yes, I've always had liked their displays.

    Drives you mad, don't it?

    Yes.-a These days every time you buy anything like this, there's always a
    hell of a struggle to get the interface into a usable form, or even as
    in my case to get the thing simply to work as advertised.

    I think most probably I'm going to have to find some way to reflash the
    firmware, but the Panasonic site said this is not possible from a USB
    stick, only via the internet.-a A while ago, when I had less detailed
    information about how the initial configuration gets set up, I had a
    chat session with them online, but had to leave because of a delivery at
    the end of the drive, and by the time I'd returned their chat software
    had timed out.-a I'll try to contact them again tomorrow to see what can
    be done.

    I've only had Panasonic TVs for years, with the current one about seven years old. I understand that they no longer make them in Japan <https:// www.slashgear.com/1846438/panasonic-tvs-who-makes-where-built/>. Does
    the back of the TV state where yours was made, JJ? Mine was made in
    Japan, but uses Firefox OS. It looks like Samsung and LG use their own Linux-based OS rather than Android, but I'm not exactly happy about
    privacy with those manufacturers. I'm not sure if I'm watching TV, or they're "watching me" watching TV if you see what I mean! Philips appear
    to use a range of OSs, but I've never really considered purchasing their TVs. Anyone here got a recent Philips TV?

    I expect that you've seen this thread: <https://www.avforums.com/threads/2025-panasonic-z90b-oled-tv- discussion-help-experiences.2532197/>

    I'm guessing that they now have no problem with "interrupted firmware updates", which may be why you don't have to bother with downloading to
    a USB stick first, checking that the download is ok, and then running
    the update from the USB stick.


    Even Philips TV's are not Philips any more. They are made in China by a company the name of which escapes me but begins with F - might be the
    outfit that make Apple phones. The Philips name is licenced but that is
    their only connection.
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Jeff Layman@Jeff@invalid.invalid to uk.tech.digital-tv on Thu Oct 22 14:43:28 2026
    From Newsgroup: uk.tech.digital-tv

    On 22/10/2026 13:52, Woody wrote:
    On Thu 22/10/2026 08:24, Jeff Layman wrote:
    On 22/10/2026 02:11, Java Jive wrote:
    On 2026-10-21 19:39, Woody wrote:

    Ultimately the 28in Panasonic non-smart we have - on a shelf behind me >>>> as I type and which is now over a decade old - has by a country mile the >>>> best screen and sound.

    Yes, I've always had liked their displays.

    Drives you mad, don't it?

    Yes.-a These days every time you buy anything like this, there's always a >>> hell of a struggle to get the interface into a usable form, or even as
    in my case to get the thing simply to work as advertised.

    I think most probably I'm going to have to find some way to reflash the
    firmware, but the Panasonic site said this is not possible from a USB
    stick, only via the internet.-a A while ago, when I had less detailed
    information about how the initial configuration gets set up, I had a
    chat session with them online, but had to leave because of a delivery at >>> the end of the drive, and by the time I'd returned their chat software
    had timed out.-a I'll try to contact them again tomorrow to see what can >>> be done.

    I've only had Panasonic TVs for years, with the current one about seven
    years old. I understand that they no longer make them in Japan <https://
    www.slashgear.com/1846438/panasonic-tvs-who-makes-where-built/>. Does
    the back of the TV state where yours was made, JJ? Mine was made in
    Japan, but uses Firefox OS. It looks like Samsung and LG use their own
    Linux-based OS rather than Android, but I'm not exactly happy about
    privacy with those manufacturers. I'm not sure if I'm watching TV, or
    they're "watching me" watching TV if you see what I mean! Philips appear
    to use a range of OSs, but I've never really considered purchasing their
    TVs. Anyone here got a recent Philips TV?

    I expect that you've seen this thread:
    <https://www.avforums.com/threads/2025-panasonic-z90b-oled-tv-
    discussion-help-experiences.2532197/>

    I'm guessing that they now have no problem with "interrupted firmware
    updates", which may be why you don't have to bother with downloading to
    a USB stick first, checking that the download is ok, and then running
    the update from the USB stick.


    Even Philips TV's are not Philips any more. They are made in China by a company the name of which escapes me but begins with F - might be the
    outfit that make Apple phones. The Philips name is licenced but that is
    their only connection.

    Looks like it's TP Vision (a subsidiary of TPV Technology, China) <https://en.wikipedia.org/wiki/TP_Vision>

    Unfortunately, it appears that they weren't (aren't?) exactly ethical
    when it comes to privacy, and could have been one of the first to start monitoring the owner's watching habits: <https://en.wikipedia.org/wiki/TP_Vision#Privacy>
    --
    Jeff
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Jeff Layman@Jeff@invalid.invalid to uk.tech.digital-tv on Thu Oct 22 14:54:54 2026
    From Newsgroup: uk.tech.digital-tv

    On 22/10/2026 11:06, Java Jive wrote:
    On 2026-10-22 08:24, Jeff Layman wrote:

    I'm guessing that they now have no problem with "interrupted firmware
    updates", which may be why you don't have to bother with downloading to
    a USB stick first, checking that the download is ok, and then running
    the update from the USB stick.

    Yeahbut, what if a power cut crashes an update in such a way as to
    prevent internet access?

    A last ditch recovery method is needed, and I suspect that one exists,
    they just don't want to tell us about it.

    Even allowing for the cost of RAM, I would have thought that they're
    using temporary internal storage to hold the update (probably <1GB). If
    the internal storage detects that it isn't holding the full update,
    perhaps because of an internet crash, it doesn't try to run it.
    --
    Jeff
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Java Jive@java@evij.com.invalid to uk.tech.digital-tv on Thu Oct 22 15:50:01 2026
    From Newsgroup: uk.tech.digital-tv

    On 2026-10-22 14:54, Jeff Layman wrote:

    On 22/10/2026 11:06, Java Jive wrote:

    On 2026-10-22 08:24, Jeff Layman wrote:

    I'm guessing that they now have no problem with "interrupted firmware
    updates", which may be why you don't have to bother with downloading to
    a USB stick first, checking that the download is ok, and then running
    the update from the USB stick.

    Yeahbut, what if a power cut crashes an update in such a way as to
    prevent internet access?

    A last ditch recovery method is needed, and I suspect that one exists,
    they just don't want to tell us about it.

    Even allowing for the cost of RAM, I would have thought that they're
    using temporary internal storage to hold the update (probably <1GB). If
    the internal storage detects that it isn't holding the full update,
    perhaps because of an internet crash, it doesn't try to run it.

    But what happens if the power fails while the re-flash is actually
    occurring?
    --

    Fake news kills!

    I may be contacted via the contact address given on my website: www.macfh.co.uk

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Andy Burns@usenet@andyburns.uk to uk.tech.digital-tv on Thu Oct 22 15:51:39 2026
    From Newsgroup: uk.tech.digital-tv

    Woody wrote:

    Even Philips TV's are not Philips any more.

    The LED lights aren't either, what do they still make?

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Jeff Layman@Jeff@invalid.invalid to uk.tech.digital-tv on Thu Oct 22 16:38:12 2026
    From Newsgroup: uk.tech.digital-tv

    On 22/10/2026 15:50, Java Jive wrote:
    On 2026-10-22 14:54, Jeff Layman wrote:

    On 22/10/2026 11:06, Java Jive wrote:

    On 2026-10-22 08:24, Jeff Layman wrote:

    I'm guessing that they now have no problem with "interrupted firmware
    updates", which may be why you don't have to bother with downloading to >>>> a USB stick first, checking that the download is ok, and then running
    the update from the USB stick.

    Yeahbut, what if a power cut crashes an update in such a way as to
    prevent internet access?

    A last ditch recovery method is needed, and I suspect that one exists,
    they just don't want to tell us about it.

    Even allowing for the cost of RAM, I would have thought that they're
    using temporary internal storage to hold the update (probably <1GB). If
    the internal storage detects that it isn't holding the full update,
    perhaps because of an internet crash, it doesn't try to run it.

    But what happens if the power fails while the re-flash is actually
    occurring?

    You're probably USCWAP, but then that could happen to any mains-powered computer-based equipment, whether it's using a direct internet
    connection, internal storage, or a USB stick to update.
    --
    Jeff
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Java Jive@java@evij.com.invalid to uk.tech.digital-tv on Thu Oct 22 17:02:36 2026
    From Newsgroup: uk.tech.digital-tv

    On 2026-10-22 16:38, Jeff Layman wrote:
    On 22/10/2026 15:50, Java Jive wrote:
    On 2026-10-22 14:54, Jeff Layman wrote:

    On 22/10/2026 11:06, Java Jive wrote:

    On 2026-10-22 08:24, Jeff Layman wrote:

    I'm guessing that they now have no problem with "interrupted firmware >>>>> updates", which may be why you don't have to bother with
    downloading to
    a USB stick first, checking that the download is ok, and then running >>>>> the update from the USB stick.

    Yeahbut, what if a power cut crashes an update in such a way as to
    prevent internet access?

    A last ditch recovery method is needed, and I suspect that one exists, >>>> they just don't want to tell us about it.

    Even allowing for the cost of RAM, I would have thought that they're
    using temporary internal storage to hold the update (probably <1GB). If
    the internal storage detects that it isn't holding the full update,
    perhaps because of an internet crash, it doesn't try to run it.

    But what happens if the power fails while the re-flash is actually
    occurring?

    You're probably USCWAP, but then that could happen to any mains-powered computer-based equipment, whether it's using a direct internet
    connection, internal storage, or a USB stick to update.

    The point is that if you are able to use a USB, you can simply start
    again, if you need it to make an internet connection, you may not be
    able to.
    --

    Fake news kills!

    I may be contacted via the contact address given on my website: www.macfh.co.uk

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Jeff Layman@Jeff@invalid.invalid to uk.tech.digital-tv on Thu Oct 22 22:18:42 2026
    From Newsgroup: uk.tech.digital-tv

    On 22/10/2026 17:02, Java Jive wrote:
    On 2026-10-22 16:38, Jeff Layman wrote:
    On 22/10/2026 15:50, Java Jive wrote:

    But what happens if the power fails while the re-flash is actually
    occurring?

    You're probably USCWAP, but then that could happen to any mains-powered
    computer-based equipment, whether it's using a direct internet
    connection, internal storage, or a USB stick to update.

    The point is that if you are able to use a USB, you can simply start
    again, if you need it to make an internet connection, you may not be
    able to.

    Indeed, but with the move in a few years to streaming-only TV, even if
    you could make the update from a USB stick, with the internet down there
    won't be anything to watch!
    --
    Jeff
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Woody@harrogate3@ntlworld.com to uk.tech.digital-tv on Thu Oct 22 22:44:56 2026
    From Newsgroup: uk.tech.digital-tv

    On Thu 22/10/2026 15:51, Andy Burns wrote:
    Woody wrote:

    Even Philips TV's are not Philips any more.

    The LED lights aren't either, what do they still make?


    Considerable quantities of medical electronics systems - CT/MRI scanners
    to name but two.

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Java Jive@java@evij.com.invalid to uk.tech.digital-tv on Thu Nov 5 18:03:14 2026
    From Newsgroup: uk.tech.digital-tv

    On 2026-10-21 18:52, Java Jive wrote:

    So back to 'Freely', which doesn't seem to work at all.-a On this TV 'Freely' is supposedly installed as a System App, not an Operator or
    User App, but some aspects of the OS have not been updated accordingly,
    for example the message at the end of scanning clearly show an
    expectation that it should be installable as a Operator or User app, but official documentation suggests that it's not.-a If I go into
    'Applications' in the configuration options, Freely is not listed as
    being installed.-a If I go into 'Live TV' in the configuration options, there is an option 'Manage Channels - 123 Channels', but if I choose
    this, the only option is 'Prime', to which I'm not subscribed. If I go
    into the Amazon App Store and search for 'free', 'freely tv' is listed
    as a result, but choosing it leads only to a repeat of the rigmarole
    from pressing the 'Freely' button on the remote.

    Somehow, I've now got a slightly different pathway, but the same end
    result. I managed to find and install an app called Freely, which now
    is listed among the installed apps. However, running it still leads to
    the same failure dialog as when pressing Freely on the remote, and at
    the end of scanning:

    "Install Freely on your TV ... providers in the UK - all for free
    Install/Cancel"
    Select 'Install'.
    "Operator App Installation
    Search and install available Operator Apps ...
    No supported Operator App found.
    Confirm"
    Select 'Confirm'.

    I've also tried
    sending it to my TV from the Amazon store, but the result is always the same.-a The whole thing seems to be a mucking fuddle.

    There is one slightly unusual thing about my system that might explain
    all this. Because my broadband comes over the Three network, and does
    not support IPv6, neither does my LAN. It could be this that is causing problems for me. I've exchanged chats and emails with Panasonic
    support, and they are looking into it.
    --

    Fake news kills!

    I may be contacted via the contact address given on my website: www.macfh.co.uk

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From SH@I.love.spam@spam.co.uk to uk.tech.digital-tv on Thu Nov 5 19:58:12 2026
    From Newsgroup: uk.tech.digital-tv

    On 05/11/2026 18:03, Java Jive wrote:
    On 2026-10-21 18:52, Java Jive wrote:

    So back to 'Freely', which doesn't seem to work at all.-a On this TV
    'Freely' is supposedly installed as a System App, not an Operator or
    User App, but some aspects of the OS have not been updated
    accordingly, for example the message at the end of scanning clearly
    show an expectation that it should be installable as a Operator or
    User app, but official documentation suggests that it's not.-a If I go
    into 'Applications' in the configuration options, Freely is not listed
    as being installed.-a If I go into 'Live TV' in the configuration
    options, there is an option 'Manage Channels - 123 Channels', but if I
    choose this, the only option is 'Prime', to which I'm not subscribed.
    If I go into the Amazon App Store and search for 'free', 'freely tv'
    is listed as a result, but choosing it leads only to a repeat of the
    rigmarole from pressing the 'Freely' button on the remote.

    Somehow, I've now got a slightly different pathway, but the same end result.-a I managed to find and install an app called Freely, which now
    is listed among the installed apps.-a However, running it still leads to
    the same failure dialog as when pressing Freely on the remote, and at
    the end of scanning:

    -a-a-a "Install Freely on your TV ... providers in the UK - all for free
    -a-a-a Install/Cancel"
    Select 'Install'.
    -a-a-a "Operator App Installation
    -a-a-a Search and install available Operator Apps ...
    -a-a-a No supported Operator App found.
    -a-a-a Confirm"
    Select 'Confirm'.

    I've also tried sending it to my TV from the Amazon store, but the
    result is always the same.-a The whole thing seems to be a mucking fuddle.

    There is one slightly unusual thing about my system that might explain
    all this.-a Because my broadband comes over the Three network, and does
    not support IPv6, neither does my LAN.-a It could be this that is causing problems for me.-a I've exchanged chats and emails with Panasonic
    support, and they are looking into it.

    So would you recommend this TV to someone like me who wants support
    Freeview, Freesat, Freely, in-house DVB-T2 CCTV modulators and also to
    receive Astra1, Hotbird, Hispasat, Eutelsat 5 West, ALl the usual BBC
    iPlayer, ITVHub, 4OD, Five, Netflix, Disney and IPTV support via M3U files?
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Java Jive@java@evij.com.invalid to uk.tech.digital-tv on Thu Nov 5 20:50:47 2026
    From Newsgroup: uk.tech.digital-tv

    On 2026-11-05 19:58, SH wrote:

    So would you recommend this TV to someone like me who wants support Freeview, Freesat, Freely, in-house DVB-T2 CCTV modulators and also to receive Astra1, Hotbird, Hispasat, Eutelsat 5 West, ALl the usual BBC iPlayer, ITVHub, 4OD, Five, Netflix, Disney and IPTV support via M3U files?

    Although screens are to some extent a matter of taste, as far as I am concerned I can recommend the screen without hesitation. I said in my
    OP that I couldn't comment on receiving satellite TV from this, so your mentioning it suggests to me that you're taking the piss, but BTAIM the
    specs suggest that anything up to and including DiSEqC 1.0 should work.
    As for in-house CCTV modulators presumably you know more about them than
    I would, as they are in your house, and again this suggests that you're
    taking the piss. All the free Internet TV that I've been able to try
    works with the notable exception of Freely, as explained in my OP.
    --

    Fake news kills!

    I may be contacted via the contact address given on my website: www.macfh.co.uk

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From SH@I.love.spam@spam.co.uk to uk.tech.digital-tv on Fri Nov 6 09:48:38 2026
    From Newsgroup: uk.tech.digital-tv

    On 05/11/2026 20:50, Java Jive wrote:
    On 2026-11-05 19:58, SH wrote:

    So would you recommend this TV to someone like me who wants support
    Freeview, Freesat, Freely, in-house DVB-T2 CCTV modulators and also to
    receive Astra1, Hotbird, Hispasat, Eutelsat 5 West, ALl the usual BBC
    iPlayer, ITVHub, 4OD, Five, Netflix, Disney and IPTV support via M3U
    files?

    Although screens are to some extent a matter of taste, as far as I am concerned I can recommend the screen without hesitation.-a I said in my
    OP that I couldn't comment on receiving satellite TV from this, so your mentioning it suggests to me that you're taking the piss, but BTAIM the specs suggest that anything up to and including DiSEqC 1.0 should work.
    As for in-house CCTV modulators presumably you know more about them than
    I would, as they are in your house, and again this suggests that you're taking the piss.-a All the free Internet TV that I've been able to try
    works with the notable exception of Freely, as explained in my OP.


    not taking the piss at all.....

    Not all T2 TV-s work with my in house DVB-T2 modulators, something to do
    with MPEG4 or HEVC support, I have 8 TV's in my house.

    Some of my TV's don't support DiSEqC at all, so they are stuck on Freesat.

    The others can support DiSEqC 1.1 but they cannot support PLS Gold as
    well as PLS Root (the latter is required to get the Italian & French TV channels from Eutelsat 5.0 West.) ANother issue is that high FEC rates
    such as 9/10 or 8/9 are not supported.

    I have my own TVHeadend server here along with Jellyfin server that
    alone has 12 IP based tuners on it. That combo has access to all the
    freeview, freesat, non-freesat satellite, in-house CCTV etc and its all
    served up as IPTV streams over my house network. So do you know if
    Jellyfin is available as an app?

    4 of the tuners on the IP based network can support PLS Gold and FEC
    rates as high as 9/10.

    As for Freely, I'm on gigabit fibre which also supports IP v6 so I
    *might* have a different experience than you.

    My main difficulty was finding a TV that has DVB-T2, DVB-S2 AND Freely
    onboard as they seem to be rare beasts. I know that Freeview and Freesat
    has an uncertain future, but need the DVB-T2 support for the inhouse
    CCTV and the DVB-S2 with DiSEqC support for the non-freesat channels as hopefully they will continue a bit longer than Freesat.
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Java Jive@java@evij.com.invalid to uk.tech.digital-tv on Fri Nov 6 18:10:32 2026
    From Newsgroup: uk.tech.digital-tv

    On 2026-11-06 09:48, SH wrote:

    not taking the piss at all.....

    In that case, apologies.

    Not all T2 TV-s work with my in house DVB-T2 modulators, something to do with MPEG4 or HEVC support,-a-a I have 8 TV's in my house.

    I can't answer that for you without having the same gear as you. I'm
    afraid the specs aren't that helpful either:

    https://www.panasonic.com/uk/consumer/televisions/4K-OLED-TV/tv-42z90beb.html#specs
    "Digital Tuner DVB-T/T2/DVB-S2/DVB-C"

    I have my own TVHeadend server here along with Jellyfin server that
    alone has 12 IP based tuners on it. That combo has access to all the freeview, freesat, non-freesat satellite, in-house CCTV etc and its all served up as IPTV streams over my house network. So do you know if
    Jellyfin is available as an app?

    Yes, I've just checked for you that it's available to install, but
    didn't try to install it.

    As for Freely, I'm on gigabit fibre which also supports IP v6 so I
    *might* have a different experience than you.

    Be interesting to see. I presume that there must be a rational reason
    why I can't seem to get it to install itself. Where others have had
    problems, they seemed to be just the usual networking and internet
    access problems, which certainly are not the problem here. That leaves
    only the IPv4/6 problem as being a likely possible cause.

    My main difficulty was finding a TV that has DVB-T2, DVB-S2 AND Freely onboard as they seem to be rare beasts. I know that Freeview and Freesat
    has an uncertain future, but need the DVB-T2 support for the inhouse
    CCTV and the DVB-S2 with DiSEqC support for the non-freesat channels as hopefully they will continue a bit longer than Freesat.

    Well this would seem to fit the bill if Freely was actually working.

    However, a possibly more important problem is that there are very few of
    these TVs available in the country now, because Panasonic have begun to
    have their TVs manufactured by another firm, and are going to be just a
    name badging henceforth. AFAIAA, these were the last model of TVs that
    fit your description above that Panasonic actually manufactured themselves.

    In a previous thread Theo linked to a refurb 55" model on eBay, but I
    can't get anything on the eBay site to work in FF ATM, not even a search
    from the home page (perhaps the infamous PHP problem?):
    https://www.ebay.co.uk/itm/206050575525

    55" would have been too big for me anyway, so at the time, August, I
    spent some time searching for the smallest model in the range, 42". I
    found 1 in Germany which I judged I probably wouldn't be able to get to
    the UK for a reasonable cost, 1 in the Far East for a knock down price
    but massive shipping costs, but finally found two actually in the UK, of
    which I bought one. However, as I was beyond the limit of the firm's
    own delivery service, I had myself to finance and arrange collection
    from them and delivery to me here in the Highlands of Scotland by
    ParcelForce, price including suitable insurance was around -u50-60. If
    you want to know where I bought that 42" model, where from the website I
    think they may still have one left, PM me using the contact address on
    my website.
    --

    Fake news kills!

    I may be contacted via the contact address given on my website: www.macfh.co.uk

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From SH@I.love.spam@spam.co.uk to uk.tech.digital-tv on Fri Nov 6 20:30:57 2026
    From Newsgroup: uk.tech.digital-tv

    On 06/11/2026 18:10, Java Jive wrote:
    On 2026-11-06 09:48, SH wrote:

    not taking the piss at all.....

    In that case, apologies.

    Not all T2 TV-s work with my in house DVB-T2 modulators, something to
    do with MPEG4 or HEVC support,-a-a I have 8 TV's in my house.

    I can't answer that for you without having the same gear as you.-a I'm afraid the specs aren't that helpful either:

    https://www.panasonic.com/uk/consumer/televisions/4K-OLED-TV/ tv-42z90beb.html#specs
    "Digital Tuner-a-a-a DVB-T/T2/DVB-S2/DVB-C"

    I have my own TVHeadend server here along with Jellyfin server that
    alone has 12 IP based tuners on it. That combo has access to all the
    freeview, freesat, non-freesat satellite, in-house CCTV etc and its
    all served up as IPTV streams over my house network. So do you know if
    Jellyfin is available as an app?

    Yes, I've just checked for you that it's available to install, but
    didn't try to install it.

    As for Freely, I'm on gigabit fibre which also supports IP v6 so I
    *might* have a different experience than you.

    Be interesting to see.-a I presume that there must be a rational reason
    why I can't seem to get it to install itself.-a Where others have had problems, they seemed to be just the usual networking and internet
    access problems, which certainly are not the problem here.-a That leaves only the IPv4/6 problem as being a likely possible cause.

    My main difficulty was finding a TV that has DVB-T2, DVB-S2 AND Freely
    onboard as they seem to be rare beasts. I know that Freeview and
    Freesat has an uncertain future, but need the DVB-T2 support for the
    inhouse CCTV and the DVB-S2 with DiSEqC support for the non-freesat
    channels as hopefully they will continue a bit longer than Freesat.

    Well this would seem to fit the bill if Freely was actually working.

    However, a possibly more important problem is that there are very few of these TVs available in the country now, because Panasonic have begun to
    have their TVs manufactured by another firm, and are going to be just a
    name badging henceforth.-a AFAIAA, these were the last model of TVs that
    fit your description above that Panasonic actually manufactured themselves.

    In a previous thread Theo linked to a refurb 55" model on eBay, but I
    can't get anything on the eBay site to work in FF ATM, not even a search from the home page (perhaps the infamous PHP problem?):
    -a-a-a https://www.ebay.co.uk/itm/206050575525

    55" would have been too big for me anyway, so at the time, August, I
    spent some time searching for the smallest model in the range, 42".-a I found 1 in Germany which I judged I probably wouldn't be able to get to
    the UK for a reasonable cost, 1 in the Far East for a knock down price
    but massive shipping costs, but finally found two actually in the UK, of which I bought one.-a However, as I was beyond the limit of the firm's
    own delivery service, I had myself to finance and arrange collection
    from them and delivery to me here in the Highlands of Scotland by ParcelForce, price including suitable insurance was around -u50-60.-a If
    you want to know where I bought that 42" model, where from the website I think they may still have one left, PM me using the contact address on
    my website.



    Do you by any chance run your own DNS like pihole, adguard home or
    technitium?

    I have found that apps and Roku sticks do not run first time after installation, always reporting an error.

    What I ended up having to do was create a hotspot on my smartphone,
    allow the Roku stick or Wi-Fi enabled TV set and then the Roku or App
    will then run.

    Then I turn off the mobile phone hotspot and get the Roku or WIfi TV to reconnect back to my home network. No more problem thereafter.

    I think there must be like a first time initialisation or a registration serial code exchange which was being blocked by my DNS even though it
    was not clear from the logs what *exactly* was being dropped.

    Another possibility is it was trying to contact a pair of public DNS
    before it would then accept the IP addresses of my own DNS which are of
    the form 192.168.xxx.yyy (all public DNS are blocked at the router level.)

    The reason why I have a home DNS is to cut out the adverts, trackers,
    dodgy websites and referrer URLS like www.awin.com

    Currently I have 3,841,722 URLs in the block list and around 43.4% of
    DNS lookups are rejected at my DNS.

    Smart TV's are notorious for being "talkative" out to the open internet
    and use ACR to report back what the TV is actually showing...... All
    very Orwellian! Hence my own DNS.....
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Davey@davey@example.invalid to uk.tech.digital-tv on Fri Nov 6 21:15:23 2026
    From Newsgroup: uk.tech.digital-tv

    On Thu, 22 Oct 2026 13:52:59 +0100
    Woody <harrogate3@ntlworld.com> wrote:
    On Thu 22/10/2026 08:24, Jeff Layman wrote:
    On 22/10/2026 02:11, Java Jive wrote:
    On 2026-10-21 19:39, Woody wrote:

    Ultimately the 28in Panasonic non-smart we have - on a shelf
    behind me as I type and which is now over a decade old - has by a
    country mile the best screen and sound.

    Yes, I've always had liked their displays.

    Drives you mad, don't it?

    Yes.-a These days every time you buy anything like this, there's
    always a hell of a struggle to get the interface into a usable
    form, or even as in my case to get the thing simply to work as
    advertised.

    I think most probably I'm going to have to find some way to
    reflash the firmware, but the Panasonic site said this is not
    possible from a USB stick, only via the internet.-a A while ago,
    when I had less detailed information about how the initial
    configuration gets set up, I had a chat session with them online,
    but had to leave because of a delivery at the end of the drive,
    and by the time I'd returned their chat software had timed out.
    I'll try to contact them again tomorrow to see what can be done.

    I've only had Panasonic TVs for years, with the current one about
    seven years old. I understand that they no longer make them in
    Japan <https:// www.slashgear.com/1846438/panasonic-tvs-who-makes-where-built/>.
    Does the back of the TV state where yours was made, JJ? Mine was
    made in Japan, but uses Firefox OS. It looks like Samsung and LG
    use their own Linux-based OS rather than Android, but I'm not
    exactly happy about privacy with those manufacturers. I'm not sure
    if I'm watching TV, or they're "watching me" watching TV if you see
    what I mean! Philips appear to use a range of OSs, but I've never
    really considered purchasing their TVs. Anyone here got a recent
    Philips TV?

    I expect that you've seen this thread: <https://www.avforums.com/threads/2025-panasonic-z90b-oled-tv- discussion-help-experiences.2532197/>

    I'm guessing that they now have no problem with "interrupted
    firmware updates", which may be why you don't have to bother with downloading to a USB stick first, checking that the download is ok,
    and then running the update from the USB stick.


    Even Philips TV's are not Philips any more. They are made in China by
    a company the name of which escapes me but begins with F - might be
    the outfit that make Apple phones. The Philips name is licenced but
    that is their only connection.
    Foxconn?
    --
    Davey.
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Java Jive@java@evij.com.invalid to uk.tech.digital-tv on Fri Nov 6 22:13:59 2026
    From Newsgroup: uk.tech.digital-tv

    On 2026-11-06 20:30, SH wrote:

    Do you by any chance run your own DNS like pihole, adguard home or technitium?

    No. My broadband setup is as follows ...

    My router is a BT Home Hub 5a hacked to run OpenWRT with a BT Assure 4G
    (a rebadged Huawei_E3372h) USB 4G dongle mounted in a window facing the nearest mobile mast and plugged via an extension lead into the router. Depending on the time of day, it gives between 15-20Mbps. It has an Id
    Mobile SIM in it, Id Mobile being an MVNO for the Three network.

    I have found that apps and Roku sticks do not run first time after installation, always reporting an error.

    What I ended up having to do was create a hotspot on my smartphone,
    allow the Roku stick or Wi-Fi enabled TV set and then the Roku or App
    will then run.

    Well, that was suggested by Panasonic, but both my mobiles have Spusu
    SIMs, which being another MVNO over Three, I didn't try because I didn't expect it to work differently from Id Mobile. However, given that you suggested it as well, I thought I might as well try it.

    And, F___ Me, IT WORKED! I now have Freely working over my normal
    internet connection.

    Thank you!
    --

    Fake news kills!

    I may be contacted via the contact address given on my website: www.macfh.co.uk

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Java Jive@java@evij.com.invalid to uk.tech.digital-tv on Sat Nov 7 01:26:36 2026
    From Newsgroup: uk.tech.digital-tv

    On 2026-11-06 18:10, Java Jive wrote:

    In a previous thread Theo linked to a refurb 55" model on eBay, but I
    can't get anything on the eBay site to work in FF ATM, not even a search from the home page (perhaps the infamous PHP problem?):
    https://www.ebay.co.uk/itm/206050575525

    The eBay site is now working again, but the one Theo linked presumably
    has long gone.

    There are two from the same range up there, but the first has a badly
    scuffed and scratched screen, and the second is rather pricey and is
    from the same supplier who sent one to me so badly packaged that it
    arrived with an impacted screen and I insisted that they pay for its
    return, which TBF they did.
    --

    Fake news kills!

    I may be contacted via the contact address given on my website: www.macfh.co.uk

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Spike@aero.spike@mail.com to uk.tech.digital-tv on Sat Nov 7 09:07:33 2026
    From Newsgroup: uk.tech.digital-tv

    Java Jive <java@evij.com.invalid> wrote:

    rCa..but both my mobiles have Spusu
    SIMs, which being another MVNO over Three, I didn't try because I didn't expect it to work differently from Id Mobile. However, given that you suggested it as well, I thought I might as well try it.

    Spusu runs on the EE network.
    --
    Spike
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From SH@I.love.spam@spam.co.uk to uk.tech.digital-tv on Sat Nov 7 10:32:13 2026
    From Newsgroup: uk.tech.digital-tv

    On 06/11/2026 22:13, Java Jive wrote:
    On 2026-11-06 20:30, SH wrote:

    Do you by any chance run your own DNS like pihole, adguard home or
    technitium?

    No.-a My broadband setup is as follows ...

    My router is a BT Home Hub 5a hacked to run OpenWRT with a BT Assure 4G
    (a rebadged Huawei_E3372h) USB 4G dongle mounted in a window facing the nearest mobile mast and plugged via an extension lead into the router. Depending on the time of day, it gives between 15-20Mbps.-a It has an Id Mobile SIM in it, Id Mobile being an MVNO for the Three network.

    That is slow.... even when my mobile phones drop to 4G, I usually can
    get around 40 mbit/s across Smarty(3), Lebara(vodafone), Tesco(O2) and
    1P mobile (EE).

    it might be worth your while to invest in a directional 4G antenna form
    the lives of Solwise provided you have an antenna connector socket on
    your 4g modem?

    I have come across an issue where certain makes and models of 4G
    antennas do not support all the frequencies 3 uses so keep an eye out
    for that if you do go down the external antenna route.

    As it happens, 3 offer a mobile internet device which is basically
    *everything in a box including the SIM* which you mount on an aerial
    pole and point it to the mast, and its powered via PoE from the Eero and
    its an ethernet cable from it, so no coaxial cable losses between the 4g antenna and the 4g modem.

    See
    https://www.three.co.uk/broadband/home-broadband/5g-outdoor-hub#settingup
    You should be able to get 3 if you are able to get idMobile. You
    never know, you might find an offer in Black Friday or Cyber Monday sales?

    There is a signal strength meter on the side of the external unit which
    helps at installation and the coverage checker is here: https://www.three.co.uk/shop/broadband/coverage-checker

    Also if you want to explore other mobile phone networks, try the BIDB
    site at https://bidb.uk/ and pop in your postcode.

    SH.



    I have found that apps and Roku sticks do not run first time after
    installation, always reporting an error.

    What I ended up having to do was create a hotspot on my smartphone,
    allow the Roku stick or Wi-Fi enabled TV set and then the Roku or App
    will then run.

    Well, that was suggested by Panasonic, but both my mobiles have Spusu
    SIMs, which being another MVNO over Three, I didn't try because I didn't expect it to work differently from Id Mobile.-a However, given that you suggested it as well, I thought I might as well try it.

    And, F___ Me, IT WORKED!-a I now have Freely working over my normal
    internet connection.

    Thank you!


    my home internet is Vodafone fibre running at 900 Mbit/s. a 8 gbit/s
    fibre is now available....

    As mentioned by Spike, Spusu does indeed run as a MVNO on EE. And as
    you've indicated, IdMobile runs on 3.

    MVNO's use different APN (Access point name) servers, not the physical network's own APN, so in turn could also then be pointing to different
    DNSes and also to different proxy servers.

    By way of example, BT provide a proxy server called Cleanfeed which has
    a blocklist of illegal sites. so an ISP can choose to use Cleanfeed or
    build their own as part of their service offering. So different proxy
    servers will inevitably be set up differently.

    So two MVNO's running on the same physical network will not always be
    using the same APN, same DNS or same Proxies.

    I'm not a fan of using "free" public DNS as effectively you are losing
    your privacy by sharing data about where you visit with the DNS
    provide... which is why Google provide their own "free" DNS.

    MY private DNS if asked for a website it does not know about, talks
    directly to the root TLD (Top level domain) servers thus bypassing the
    public DNS completely.

    anyway, I am pleased for you that you've got your Freely issue sorted :-)
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Chris Green@cl@isbd.net to uk.tech.digital-tv on Sat Nov 7 12:38:01 2026
    From Newsgroup: uk.tech.digital-tv

    SH <I.love.spam@spam.co.uk> wrote:
    I'm not a fan of using "free" public DNS as effectively you are losing
    your privacy by sharing data about where you visit with the DNS
    provide... which is why Google provide their own "free" DNS.

    MY private DNS if asked for a website it does not know about, talks
    directly to the root TLD (Top level domain) servers thus bypassing the public DNS completely.

    Isn't that a bit anti-social in that, if everyone did the same, the TLD
    servers would be overloaded.

    I have cacheing DNS (dnsmasq) running on my router and for 'upstream' DNS
    it uses my ISP's DNS.
    --
    Chris Green
    -+
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From SH@i.love@spam.com to uk.tech.digital-tv on Sat Nov 7 16:40:55 2026
    From Newsgroup: uk.tech.digital-tv

    On 07/11/2026 12:38, Chris Green wrote:
    SH <I.love.spam@spam.co.uk> wrote:
    I'm not a fan of using "free" public DNS as effectively you are losing
    your privacy by sharing data about where you visit with the DNS
    provide... which is why Google provide their own "free" DNS.

    MY private DNS if asked for a website it does not know about, talks
    directly to the root TLD (Top level domain) servers thus bypassing the
    public DNS completely.

    Isn't that a bit anti-social in that, if everyone did the same, the TLD servers would be overloaded.

    I have cacheing DNS (dnsmasq) running on my router and for 'upstream' DNS
    it uses my ISP's DNS.


    my DNS also have caching. SO the only time I use the root TLDs is for
    new places I might wander over to.

    It also provides some protection against hacked public DNS or redirects
    to malicious or poisoned DNS.

    Its a feature available to any Linux based system if you install UNBOUND.

    SH
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Chris Green@cl@isbd.net to uk.tech.digital-tv on Sat Nov 7 16:50:38 2026
    From Newsgroup: uk.tech.digital-tv

    SH <i.love@spam.com> wrote:
    On 07/11/2026 12:38, Chris Green wrote:
    SH <I.love.spam@spam.co.uk> wrote:
    I'm not a fan of using "free" public DNS as effectively you are losing
    your privacy by sharing data about where you visit with the DNS
    provide... which is why Google provide their own "free" DNS.

    MY private DNS if asked for a website it does not know about, talks
    directly to the root TLD (Top level domain) servers thus bypassing the
    public DNS completely.

    Isn't that a bit anti-social in that, if everyone did the same, the TLD servers would be overloaded.

    I have cacheing DNS (dnsmasq) running on my router and for 'upstream' DNS it uses my ISP's DNS.


    my DNS also have caching. SO the only time I use the root TLDs is for
    new places I might wander over to.

    ... and every time the DNS expires.
    --
    Chris Green
    -+
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Java Jive@java@evij.com.invalid to uk.tech.digital-tv on Sat Nov 7 18:54:32 2026
    From Newsgroup: uk.tech.digital-tv

    On 2026-11-07 10:32, SH wrote:

    On 06/11/2026 22:13, Java Jive wrote:

    My router is a BT Home Hub 5a hacked to run OpenWRT with a BT Assure
    4G (a rebadged Huawei_E3372h) USB 4G dongle mounted in a window facing
    the nearest mobile mast and plugged via an extension lead into the
    router. Depending on the time of day, it gives between 15-20Mbps.-a It
    has an Id Mobile SIM in it, Id Mobile being an MVNO for the Three
    network.

    That is slow.... even when my mobile phones drop to 4G, I usually can
    get around 40 mbit/s across Smarty(3), Lebara(vodafone), Tesco(O2) and
    1P mobile (EE).

    it might be worth your while to invest in a directional 4G antenna form
    the lives of Solwise provided you have an antenna connector socket on
    your 4g modem?

    I have come across an issue where certain makes and models of 4G
    antennas do not support all the frequencies 3 uses so keep an eye out
    for that if you do go down the external antenna route.

    As it happens, 3 offer a mobile internet device which is basically *everything in a box including the SIM* which you mount on an aerial
    pole and point it to the mast, and its powered via PoE from the Eero and
    its an ethernet cable from it, so no coaxial cable losses between the 4g antenna and the 4g modem.

    See https://www.three.co.uk/broadband/home-broadband/5g-outdoor-hub#settingup -a-a You should be able to get 3 if you are able to get idMobile. You never know, you might find an offer in Black Friday or Cyber Monday sales?

    There is a signal strength meter on the side of the external unit which helps at installation and the coverage checker is here: https://www.three.co.uk/shop/broadband/coverage-checker

    No 5G here from anyone here. Further, I would presume that I can only
    get that device with a Pay Monthly contract from Three, but couldn't
    check because their site wouldn't work in FF, which is exactly the sort
    of reason why I left them previously, after they 'upgraded' their
    website and app which necessitated existing users re-registering and re-entering all their account details, and their new 'upgraded' site
    didn't work in one browser so I had to do it all again in another, after
    at their behest uninstalling their old app from my old tablet their new 'upgraded' app wouldn't install on it, then, the final straw, when it
    came to doing it all over again for the second account, I had to use a different email address. As someone trained in data programming, this
    told me that they hadn't a fucking clue what they were doing, because
    they obviously weren't keeping their data in Third Normal Form (TNF), a
    very basic data programming error.

    Also if you want to explore other mobile phone networks, try the BIDB
    site at https://bidb.uk/ and pop in your postcode.

    Curiously, at first I misread the legend on their map gaining an
    erroneous impression that 3G was still working here, meaning I should
    still be able to make a call from my old tablet, which is 4G but can not
    dial over 4G, so I tried it, and it successfully rang my mobile. When
    at my cousin's in Glenfinnan, it can't do that. Then I looked at the
    map again and realised that I'd misread the legend, so I presume that 3G
    is in fact still working here, despite what it says on their map.

    You denigrate my 15-20Mbps, but it's 10x faster at about 3/4 of the
    price I was then getting via ADSL, which moreover was frequently failing altogether, and it seemed to be almost impossible ever to get an
    OpenReach engineer out. We submitted a request for FTTC around this
    area when Lairg was done, and a couple of years later tried again and as
    a result we have an FTTC green cabinet about 2-2.5 miles away, but no
    further fibre expansion appears to be planned. There is another much
    faster wireless broadband option through a local firm who have a
    transmitter the other side of the loch, but it's double the -u15 I'm
    paying Id Mobile.

    As mentioned by Spike, Spusu does indeed run as a MVNO on EE. And as
    you've indicated, IdMobile runs on 3.

    Spike is plonked here, but you're both right. I'm not quite sure how originally I came to believe that it was running on Three, but I think
    it must have been quite a while ago and until now hadn't been challenged
    on my error.

    MVNO's use different APN (Access point name) servers, not the physical network's own APN, so in turn could also then be pointing to different
    DNSes and also to different proxy servers.

    By way of example, BT provide a proxy server called Cleanfeed which has
    a blocklist of illegal sites. so an ISP can choose to use Cleanfeed or
    build their own as part of their service offering. So different proxy servers will inevitably be set up differently.

    So two MVNO's running on the same physical network will not always be
    using the same APN, same DNS or same Proxies.

    Yes, I realised after completing my last post that different MVNOs may
    well configure their networks differently.

    anyway, I am pleased for you that you've got your Freely issue sorted :-)

    Tx again for your suggestion that helped with that.
    --

    Fake news kills!

    I may be contacted via the contact address given on my website: www.macfh.co.uk

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From SH@I.love.spam@spam.co.uk to uk.tech.digital-tv on Sun Nov 8 19:50:46 2026
    From Newsgroup: uk.tech.digital-tv

    On 07/11/2026 18:54, Java Jive wrote:
    On 2026-11-07 10:32, SH wrote:

    On 06/11/2026 22:13, Java Jive wrote:

    My router is a BT Home Hub 5a hacked to run OpenWRT with a BT Assure
    4G (a rebadged Huawei_E3372h) USB 4G dongle mounted in a window
    facing the nearest mobile mast and plugged via an extension lead into
    the router. Depending on the time of day, it gives between
    15-20Mbps.-a It has an Id Mobile SIM in it, Id Mobile being an MVNO
    for the Three network.

    If my memory serves me right, that E3372h dongle has two little plastic trapdoors down on edge. if you open them up, you will hopefully find two antenna connector sockets. They will be CRC9 or TS-5 sockets. so one
    could buy a MIMO antenna.

    Choices:

    1. Poynting XPOL-A0002
    - Directional, cross-polarised MIMO
    - Outdoor wall or pole mounting
    - Designed for 4G LTE
    - Requires two suitable antenna cables/adapters.
    Solwise XPOL-A0002

    2. Poynting XPOL-A0001
    - Omnidirectional
    - Cross-polarised MIMO
    - No precise alignment required
    - Good if the signal arrives via reflections or multiple masts.
    Solwise XPOL-A0001

    Both are available on the Solwise website

    No 5G here from anyone here.-a Further, I would presume that I can only
    get that device with a Pay Monthly contract from Three, but couldn't
    check because their site wouldn't work in FF, which is exactly the sort
    of reason why I left them previously, after they 'upgraded' their
    website and app which necessitated existing users re-registering and re- entering all their account details, and their new 'upgraded' site didn't work in one browser so I had to do it all again in another, after at
    their behest uninstalling their old app from my old tablet their new 'upgraded' app wouldn't install on it, then, the final straw, when it
    came to doing it all over again for the second account, I had to use a different email address.-a As someone trained in data programming, this
    told me that they hadn't a fucking clue what they were doing, because
    they obviously weren't keeping their data in Third Normal Form (TNF), a
    very basic data programming error.

    How interesting.... I use FF too and had no problems browsing the Three website


    You denigrate my 15-20Mbps, but it's 10x faster at about 3/4 of the
    price I was then getting via ADSL, which moreover was frequently failing altogether, and it seemed to be almost impossible ever to get an
    OpenReach engineer out.-a We submitted a request for FTTC around this
    area when Lairg was done, and a couple of years later tried again and as
    a result we have an FTTC green cabinet about 2-2.5 miles away, but no further fibre expansion appears to be planned.-a There is another much faster wireless broadband option through a local firm who have a
    transmitter the other side of the loch, but it's double the -u15 I'm
    paying Id Mobile.

    I have a farming friend and he was on ADSL and got just 10 mbit/s on a
    good day. No chance of FTTC or even FTTRN let alone FTTP/FTTH.

    I actually went around his farm with a 5g phone and 4 sims and found
    that 3 was the fastest at a certain point on his farm where I was
    getting over 40 mbit/s. So I suggested either that with a 4g router, an unlimited data SIM and an external aerial or get Starlink.

    He got starlink and now gets over 200 mbit/s. He is now happier than a
    pig in muck!

    Incidentally, there are mast sharing agreements between Vodafone & O2
    via Vantage Towers and, also between EE & 3 via MBNL.

    So out of interest, have you ever tried the Spusu SIM in the dongle?

    I do find speedtesting tends to go in the following order EE(fastest) -
    Voda - o2 - 3(slowest) around here.

    In remote areas there is the SRN which is a shared rural network where
    all 4 nets co-pay and co-share the SRN masts. So you may well be served
    by a SRN mast?

    MVNO's use different APN (Access point name) servers, not the physical
    network's own APN, so in turn could also then be pointing to different
    DNSes and also to different proxy servers.

    By way of example, BT provide a proxy server called Cleanfeed which
    has a blocklist of illegal sites. so an ISP can choose to use
    Cleanfeed or build their own as part of their service offering. So
    different proxy servers will inevitably be set up differently.

    So two MVNO's running on the same physical network will not always be
    using the same APN, same DNS or same Proxies.

    Yes, I realised after completing my last post that different MVNOs may
    well configure their networks differently.


    The only way that the app or Roku stick could avoid being logged by my
    DNS is they must have been attempting to "phone home" to a specific hard
    coded IP address rather than a URL which appears to be blocked on
    Vodafone Gigafast but wasn't on 1p Mobile (EE). That specific IP address
    must be some kind of authentication server to activate & enable the Roku
    / App to be authorised before being let loose on the rest of the internet.

    Next time I set up a new app or new Roku, I will have to get Wireshark
    set up and mirror one of the ethernet switch ports to the one being used
    by the Roku / App so I can she what it is trying to contact IP address wise.

    actually come to think of it, IP v6 is disabled on my home network but
    it isn't on 1p Mobile. SO perhaps the authentication service is on a IP
    v6 only address? There is TEREDO tunnelling that should take care of a
    IP v4 device wanting to contact a IP v6 address?
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Spike@aero.spike@mail.com to uk.tech.digital-tv on Sun Nov 8 22:36:42 2026
    From Newsgroup: uk.tech.digital-tv

    SH <I.love.spam@spam.co.uk> wrote:

    [rCa]

    2. Poynting XPOL-A0001
    - Omnidirectional
    - Cross-polarised MIMO
    - No precise alignment required
    - Good if the signal arrives via reflections or multiple masts.

    On that last pointrCa

    If a signal arrives at an antenna from multiple reflections, there is the possibility that they could add destructively and the resultant signal
    received be significantly reduced. The same holds true for signals from multiple masts - if the path lengths from two masts differ by half a wavelength, then they will add destructively, assuming they were
    transmitting in phase.

    Trial and error is the only way to ensure good received signal strength.
    --
    Spike
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Java Jive@java@evij.com.invalid to uk.tech.digital-tv on Mon Nov 9 00:50:49 2026
    From Newsgroup: uk.tech.digital-tv

    On 2026-11-08 19:50, SH wrote:

    How interesting.... I use FF too and had no problems browsing the Three website

    Following the link you gave, going to the top menu bar, clicking on any
    of the three options, the first of which is 'Shop', does absolutely
    nothing in FF 15.44.0esr with YesScript2 running but not working on that
    site, and UBlockOrigin either enabled, which reported 20 or so hits, or disabled.

    You denigrate my 15-20Mbps, but it's 10x faster at about 3/4 of the
    price I was then getting via ADSL, which moreover was frequently
    failing altogether, and it seemed to be almost impossible ever to get
    an OpenReach engineer out.-a We submitted a request for FTTC around
    this area when Lairg was done, and a couple of years later tried again
    and as a result we have an FTTC green cabinet about 2-2.5 miles away,
    but no further fibre expansion appears to be planned.-a There is
    another much faster wireless broadband option through a local firm who
    have a transmitter the other side of the loch, but it's double the -u15
    I'm paying Id Mobile.

    I have a farming friend and he was on ADSL and got just 10 mbit/s on a
    good day.-a No chance of FTTC or even FTTRN let alone FTTP/FTTH.

    I actually went around his farm with a 5g phone and 4 sims and found
    that 3 was the fastest at a certain point on his farm where I was
    getting over 40 mbit/s. So I suggested either that with a 4g router, an unlimited data SIM and an external aerial or get Starlink.

    He got starlink and now gets over 200 mbit/s. He is now happier than a
    pig in muck!

    Incidentally, there are mast sharing agreements between Vodafone & O2
    via Vantage Towers and, also between EE & 3 via MBNL.

    So out of interest, have you ever tried the Spusu SIM in the dongle?

    No, unfortunately Spusu do not do unlimited deals. EE do, but they're
    around double what I'm currently paying.

    I do find speedtesting tends to go in the following order EE(fastest) -
    Voda - o2 - 3(slowest) around here.

    In remote areas there is the SRN which is a shared rural network where
    all 4 nets co-pay and co-share the SRN masts. So you may well be served
    by a SRN mast?

    Dunno. Originally our mobile signal came from the same mast as the TV
    relay, on a hill called The Ord SW of Lairg. Then some years back, as
    part of EE taking on the Emergency Services coverage, there was a plan
    to put one by the Loch side road, but we all complained that it would be
    an eyesore in a spot where tourists stop apparently for no other reason
    than to take photos, and anyway wouldn't give us very good coverage as
    there is a slight hill between most of the local houses and the proposed location that the mast wouldn't have been tall enough to see over, so
    instead they placed it between Lairg and Dalchork, away from the road
    but at a higher elevation, where it can be seen from the majority of our houses, and our reception improved noticeably. We considered that a win
    both ways.

    actually come to think of it, IP v6 is disabled on my home network but
    it isn't on 1p Mobile. SO perhaps the authentication service is on a IP
    v6 only address?-a There is TEREDO tunnelling that should take care of a
    IP v4 device wanting to contact a IP v6 address?

    But none of my PCs can see any IPv6 address; I presume that's why the
    Teredo Tunnelling devices all have an exclamation mark in Device Manager.
    --

    Fake news kills!

    I may be contacted via the contact address given on my website: www.macfh.co.uk

    --- Synchronet 3.22a-Linux NewsLink 1.2