• Re: Looking for a decent VOIP provider for a small business, 4 phones and 1 remote one

    From Postman Pat@at@the-post-office-not.com to uk.telecom on Thu Oct 29 12:56:43 2026
    From Newsgroup: uk.telecom

    Almost a year later I am having to revisit this issue, and I am
    looking for recommendations.

    The main A&A VOIP system is working most of the time. Sometimes call
    transfers fail but not much.

    I now find, yet again, that the 5th "office" phone which is at my
    house no longer rings on incoming calls. A&A are unhelpful, saying in
    their usual arrogant way that it won't work through NAT. Well I know
    that which is why I have port 5060 open and forwarded to the phone's
    internal LAN IP. And this works. It stopped working at one point and
    then started, and now I've found it stopped working again.

    I am fed up with this and want to move the whole VOIP stuff to another
    firm.

    Is Voipfone.co.uk still OK? I am at home with them, in fibre, and
    there has been no downtime so I have had no interaction with them.

    We have four Snom phones at the office and one at my house. A&A are
    running a "virtual PBX" so each of the phones has its own IP. Some
    have told me this is highly unusual.

    Many thanks :)



    Postman Pat <at@the-post-office-not.com> wrote:

    This sounds trivial but for some reason it isn't.

    We have FTTP with Andrews & Arnold; been with them for some years.

    We also have a VOIP system with 5 Snom POE phones. One of these 5 is
    at my house.

    Everything is on fixed IPs.

    For the 4 phones, A&A assign four IPs. This is some sort of "managed
    PBX" which they implement on their servers. Everybody I talk to laughs
    at having four IPs for four phones :)

    A 5th IP is used for our LAN. The router is a Draytek 2960 with
    pass-through for the four phones, port 5060.

    The system has mostly worked but with frequent weird behaviour. For a
    long time, call transfers would fail. A&A tracked this down to timing >problems on inter-server handovers. More recently, we have the whole
    "ring group" ringing but when the call is answered the other phones
    keep ringing, until somebody goes round them all and picks them up and
    puts them back down.

    If we had a lot of incoming calls, the system would be unworkable, so
    I don't understand how they get away with this. They supplied all the
    phones too.

    At home I have a "landline" with an old Panasonic 3x8 PBX and have the
    number with Voipfone.co.uk and a u50 Grandstream box. That works
    perfectly. I have enquired with Voipfone about the business stuff but
    they never replied so probably not interested.

    But clearly "going analog" with a similar setup, and four old style
    phones and an old PBX, would work great. For 30 years we had a Siemens
    ISDN phone system which was 100.000% reliable. But then how would one
    set up the 5th phone at my house which is on the same ring group?

    A&A is a good ISP but they have a serious "attitude issue" whereby the >customer is a bit stupid. I think this is the result of many years of >everybody in Usenet saying they are the best UK ISP for business, and
    it has gone to their heads :) Well I certainly would not use say
    Vodafone (OK for a phone but a script monkey call centre in India,
    like most) but I find Voipfone OK for my home FTTP (they do FTTP as
    well as basic VOIP).

    I am all ears for any recommendations :)
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Richmond@dnomhcir@gmx.com to uk.telecom on Thu Oct 29 13:35:18 2026
    From Newsgroup: uk.telecom

    Postman Pat <at@the-post-office-not.com> writes:

    We have four Snom phones at the office and one at my house. A&A are
    running a "virtual PBX" so each of the phones has its own IP. Some
    have told me this is highly unusual.


    It may be unusual, but it is the way SIP was originally designed to
    work, which is why A&A likes it that way. (I think).

    Your 5th phone is connected via a draytech router, maybe you could try switching on SIP ALG on that router? A&A doesn't like SIP ALG because it
    can be implemented badly, but it works fine on my Zyxel router.

    I found the configuration of VOIP using its own IP though a NAT router
    rather complicated because you have to open ports for RTP/RTCP.

    Do you find all outbound calls work? I found that some didn't and it
    depended on the recipients phone system, until I switched on SIP ALG.

    https://support.aa.net.uk/VoIP_Firewall
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Chris Green@cl@isbd.net to uk.telecom on Thu Oct 29 13:46:23 2026
    From Newsgroup: uk.telecom

    Postman Pat <at@the-post-office-not.com> wrote:
    Almost a year later I am having to revisit this issue, and I am
    looking for recommendations.

    The main A&A VOIP system is working most of the time. Sometimes call transfers fail but not much.

    I now find, yet again, that the 5th "office" phone which is at my
    house no longer rings on incoming calls. A&A are unhelpful, saying in
    their usual arrogant way that it won't work through NAT. Well I know
    that which is why I have port 5060 open and forwarded to the phone's
    internal LAN IP. And this works. It stopped working at one point and
    then started, and now I've found it stopped working again.

    I am fed up with this and want to move the whole VOIP stuff to another
    firm.

    Is Voipfone.co.uk still OK? I am at home with them, in fibre, and
    there has been no downtime so I have had no interaction with them.

    We have four Snom phones at the office and one at my house. A&A are
    running a "virtual PBX" so each of the phones has its own IP. Some
    have told me this is highly unusual.

    Wouldn't the best/simplest answer be to get IPV6 working? Then there is
    simply no issue with NAT.

    I've recently moved quite a few things to IPV6 and have been pleasantly surprised how simple it has been.
    --
    Chris Green
    -+
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Postman Pat@at@the-post-office-not.com to uk.telecom on Thu Oct 29 14:48:39 2026
    From Newsgroup: uk.telecom


    Richmond <dnomhcir@gmx.com> wrote:

    Postman Pat <at@the-post-office-not.com> writes:

    We have four Snom phones at the office and one at my house. A&A are
    running a "virtual PBX" so each of the phones has its own IP. Some
    have told me this is highly unusual.


    It may be unusual, but it is the way SIP was originally designed to
    work, which is why A&A likes it that way. (I think).

    Your 5th phone is connected via a draytech router, maybe you could try >switching on SIP ALG on that router? A&A doesn't like SIP ALG because it
    can be implemented badly, but it works fine on my Zyxel router.

    I found the configuration of VOIP using its own IP though a NAT router
    rather complicated because you have to open ports for RTP/RTCP.

    Do you find all outbound calls work? I found that some didn't and it
    depended on the recipients phone system, until I switched on SIP ALG.

    Yes, outbound calls work fine.

    https://support.aa.net.uk/VoIP_Firewall

    I saw that but can't see what has changed. The phone is on the correct
    internal LAN IP (just gone into its config) and the router is set up
    as it always was.

    Something has changed...
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Postman Pat@at@the-post-office-not.com to uk.telecom on Thu Oct 29 15:31:48 2026
    From Newsgroup: uk.telecom

    I've been onto Voipfone and they can do a good package, 5 quid per
    phone, and a virtual PBX also. They also do not use port forwarding;
    their phones do a keep alive every 60s. That is a lot cleaner.

    Problem is, our phone will get cut off for about a week.

    The only alternative is to move the whole lot from A&A to Voipfone.
    Problem with that is that I will have the same ISP for home and
    office, which is not a good idea.


    Richmond <dnomhcir@gmx.com> wrote:

    Postman Pat <at@the-post-office-not.com> writes:

    We have four Snom phones at the office and one at my house. A&A are
    running a "virtual PBX" so each of the phones has its own IP. Some
    have told me this is highly unusual.


    It may be unusual, but it is the way SIP was originally designed to
    work, which is why A&A likes it that way. (I think).

    Your 5th phone is connected via a draytech router, maybe you could try >switching on SIP ALG on that router? A&A doesn't like SIP ALG because it
    can be implemented badly, but it works fine on my Zyxel router.

    I found the configuration of VOIP using its own IP though a NAT router
    rather complicated because you have to open ports for RTP/RTCP.

    Do you find all outbound calls work? I found that some didn't and it
    depended on the recipients phone system, until I switched on SIP ALG.

    https://support.aa.net.uk/VoIP_Firewall
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Theo@theom+news@chiark.greenend.org.uk to uk.telecom on Fri Oct 30 12:08:37 2026
    From Newsgroup: uk.telecom

    Chris Green <cl@isbd.net> wrote:
    Postman Pat <at@the-post-office-not.com> wrote:
    Almost a year later I am having to revisit this issue, and I am
    looking for recommendations.

    The main A&A VOIP system is working most of the time. Sometimes call transfers fail but not much.

    I now find, yet again, that the 5th "office" phone which is at my
    house no longer rings on incoming calls. A&A are unhelpful, saying in
    their usual arrogant way that it won't work through NAT. Well I know
    that which is why I have port 5060 open and forwarded to the phone's internal LAN IP. And this works. It stopped working at one point and
    then started, and now I've found it stopped working again.

    I'm surprised this works, since the outgoing SIP (or RTP?) packets will have your LAN address embedded in them, which the A&A server doesn't know what to
    do with.

    The SIP ALG should inspect the packets passing through the router and
    rewrite them with the correct public IP.

    I've used A&A on a variety of broadband connections with a variety of
    provider routers (and double NAT through two routers), and at most it needed the SIP ALG turning on in the router settings.

    Wouldn't the best/simplest answer be to get IPV6 working? Then there is simply no issue with NAT.

    Yes, I think A&A assume you don't need NAT because they offer you IPv6. As you're an A&A broadband customer you by definition have IPv6 on your connection. It would seem to make sense to do the thing they offer support for.

    (or is the problem your home broadband is a different provider who doesn't
    have IPv6? As above even IPv4 double-NAT has never been a problem for me)

    Theo
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Postman Pat@at@the-post-office-not.com to uk.telecom on Fri Oct 30 16:45:42 2026
    From Newsgroup: uk.telecom


    Theo <theom+news@chiark.greenend.org.uk> wrote:

    Chris Green <cl@isbd.net> wrote:
    Postman Pat <at@the-post-office-not.com> wrote:
    Almost a year later I am having to revisit this issue, and I am
    looking for recommendations.

    The main A&A VOIP system is working most of the time. Sometimes call
    transfers fail but not much.

    I now find, yet again, that the 5th "office" phone which is at my
    house no longer rings on incoming calls. A&A are unhelpful, saying in
    their usual arrogant way that it won't work through NAT. Well I know
    that which is why I have port 5060 open and forwarded to the phone's
    internal LAN IP. And this works. It stopped working at one point and
    then started, and now I've found it stopped working again.

    I'm surprised this works, since the outgoing SIP (or RTP?) packets will have >your LAN address embedded in them, which the A&A server doesn't know what to >do with.

    Outgoing calls have always worked. The phone is configured with an A&A
    server URL etc.

    The SIP ALG should inspect the packets passing through the router and
    rewrite them with the correct public IP.

    I've been reading up on this.

    It seems that with ALG you do *not* enable port forwarding, and the
    router works out the phone's private IP by inspecting its *outgoing* (presumably keep-alive) packets. So if it gets a 5060 packet, it knows
    where to send it.

    But then I don't get the opportunity to enable the forwarding only
    from A&A IP ranges, which is obviously crucial otherwise all of china
    will be in there hammering port 5060 ;)

    So currently I have both port forwarding (with the above firewall
    rule) and SIP ALG and the phone rings OK.

    Voipfone have a much cleaner system where their phones keep alive
    every 60s so not port forwarding or any other router config is needed.

    I've used A&A on a variety of broadband connections with a variety of >provider routers (and double NAT through two routers), and at most it needed >the SIP ALG turning on in the router settings.

    Digging into this, it looks like A&A may have changed their server
    config:

    From Claude: If the router hasnAt changed, then the change was on the
    other side, so the provider is the likelier explanation. A typical
    candidate is how their servers handle NAT. Many SIP providers quietly
    correct for private addresses in the Contact and SDP headers, by
    replying to the address and port the packet actually came from. If
    they tightened or changed that behaviour, phones behind NAT without an
    ALG would stop working, and enabling the ALG would fix them, exactly
    as you saw.

    A&A would never admit that though ;)

    I *am* concerned about security. AFAICT the inbound IP firewall rule
    prevents VOIP phone fraud, but if ALG allows incoming packets to
    bypass NAT, that is bad because they could be malformed.

    Wouldn't the best/simplest answer be to get IPV6 working? Then there is
    simply no issue with NAT.

    Yes, I think A&A assume you don't need NAT because they offer you IPv6. As >you're an A&A broadband customer you by definition have IPv6 on your >connection. It would seem to make sense to do the thing they offer support >for.

    I don't want to touch IPV6. I have other stuff set up which doesn't
    support it, and life is too short :)

    (or is the problem your home broadband is a different provider who doesn't >have IPv6? As above even IPv4 double-NAT has never been a problem for me)

    Yes my home fibre is Voipfone and that phone is on A&A.

    Voipfone can take over the office number and I am sure their system is
    much better (their support is certainly excellent) but the number
    would apparently go dead for 7 days, which is not acceptable. To avoid
    this, I would need to transfer the whole office to Voipfone but then I
    have to reconfig a lot of stuff - which I can do if needed.
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Chris Green@cl@isbd.net to uk.telecom on Fri Oct 30 17:19:25 2026
    From Newsgroup: uk.telecom

    Postman Pat <at@the-post-office-not.com> wrote:

    Wouldn't the best/simplest answer be to get IPV6 working? Then there is
    simply no issue with NAT.

    Yes, I think A&A assume you don't need NAT because they offer you IPv6. As >you're an A&A broadband customer you by definition have IPv6 on your >connection. It would seem to make sense to do the thing they offer support >for.

    I don't want to touch IPV6. I have other stuff set up which doesn't
    support it, and life is too short :)

    Enabling/confguring IPV6 doesn't stop IPV4 working.
    --
    Chris Green
    -+
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Richmond@dnomhcir@gmx.com to uk.telecom on Fri Oct 30 17:38:56 2026
    From Newsgroup: uk.telecom

    Postman Pat <at@the-post-office-not.com> writes:

    Theo <theom+news@chiark.greenend.org.uk> wrote:

    Chris Green <cl@isbd.net> wrote:
    Postman Pat <at@the-post-office-not.com> wrote:
    Almost a year later I am having to revisit this issue, and I am
    looking for recommendations.

    The main A&A VOIP system is working most of the time. Sometimes call
    transfers fail but not much.

    I now find, yet again, that the 5th "office" phone which is at my
    house no longer rings on incoming calls. A&A are unhelpful, saying in
    their usual arrogant way that it won't work through NAT. Well I know
    that which is why I have port 5060 open and forwarded to the phone's
    internal LAN IP. And this works. It stopped working at one point and
    then started, and now I've found it stopped working again.

    I'm surprised this works, since the outgoing SIP (or RTP?) packets will have >>your LAN address embedded in them, which the A&A server doesn't know what to >>do with.

    Outgoing calls have always worked. The phone is configured with an A&A
    server URL etc.

    The SIP ALG should inspect the packets passing through the router and >>rewrite them with the correct public IP.

    I've been reading up on this.

    It seems that with ALG you do *not* enable port forwarding, and the
    router works out the phone's private IP by inspecting its *outgoing* (presumably keep-alive) packets. So if it gets a 5060 packet, it knows
    where to send it.

    But then I don't get the opportunity to enable the forwarding only
    from A&A IP ranges, which is obviously crucial otherwise all of china
    will be in there hammering port 5060 ;)

    So currently I have both port forwarding (with the above firewall
    rule) and SIP ALG and the phone rings OK.

    Voipfone have a much cleaner system where their phones keep alive
    every 60s so not port forwarding or any other router config is needed.

    I've used A&A on a variety of broadband connections with a variety of >>provider routers (and double NAT through two routers), and at most it needed >>the SIP ALG turning on in the router settings.

    Digging into this, it looks like A&A may have changed their server
    config:

    From Claude: If the router hasnrCOt changed, then the change was on the
    other side, so the provider is the likelier explanation. A typical
    candidate is how their servers handle NAT. Many SIP providers quietly
    correct for private addresses in the Contact and SDP headers, by
    replying to the address and port the packet actually came from. If
    they tightened or changed that behaviour, phones behind NAT without an
    ALG would stop working, and enabling the ALG would fix them, exactly
    as you saw.

    A&A would never admit that though ;)

    I *am* concerned about security. AFAICT the inbound IP firewall rule
    prevents VOIP phone fraud, but if ALG allows incoming packets to
    bypass NAT, that is bad because they could be malformed.

    Wouldn't the best/simplest answer be to get IPV6 working? Then there is
    simply no issue with NAT.

    Yes, I think A&A assume you don't need NAT because they offer you IPv6. As >>you're an A&A broadband customer you by definition have IPv6 on your >>connection. It would seem to make sense to do the thing they offer support >>for.

    I don't want to touch IPV6. I have other stuff set up which doesn't
    support it, and life is too short :)

    (or is the problem your home broadband is a different provider who doesn't >>have IPv6? As above even IPv4 double-NAT has never been a problem for me)

    Yes my home fibre is Voipfone and that phone is on A&A.

    Voipfone can take over the office number and I am sure their system is
    much better (their support is certainly excellent) but the number
    would apparently go dead for 7 days, which is not acceptable. To avoid
    this, I would need to transfer the whole office to Voipfone but then I
    have to reconfig a lot of stuff - which I can do if needed.

    Maybe A&A does not like the phone's IP address not being on their
    network? I have managed to make calls using Linphone on Android. And for
    it to ring there is an option in that app to send keep alive
    messages. The phone has its own ipv6 address but I disabled ipv6 in the settings of Linphone to make it work.

    There is an option on the A&A control pages to disable use of the phone
    number from other IP addresses as a security measure. It is off by
    default so it should work from your home IP.

    You could try getting it to work with Linphone and also maybe depending
    on your router plug in a traditional phone to the router and see if that
    works.

    You could switch on SIP ALG just to see if it works.
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Theo@theom+news@chiark.greenend.org.uk to uk.telecom on Fri Oct 30 17:45:11 2026
    From Newsgroup: uk.telecom

    Postman Pat <at@the-post-office-not.com> wrote:

    Theo <theom+news@chiark.greenend.org.uk> wrote:

    The SIP ALG should inspect the packets passing through the router and >rewrite them with the correct public IP.

    I've been reading up on this.

    It seems that with ALG you do *not* enable port forwarding, and the
    router works out the phone's private IP by inspecting its *outgoing* (presumably keep-alive) packets. So if it gets a 5060 packet, it knows
    where to send it.

    But then I don't get the opportunity to enable the forwarding only
    from A&A IP ranges, which is obviously crucial otherwise all of china
    will be in there hammering port 5060 ;)

    I think the idea is that the SIP ALG sees a local device connecting to A&A
    port 5060, and rewrites it with the public IP but also remembers the LAN IP. When media connections come back from A&A to your router, the ALG knows to forward them on to the phone's LAN IP.

    If somebody else sends you SIP or RTP traffic, it doesn't come from the A&A
    IP and the ALG doesn't forward it, so the firewall dumps it.

    That means you don't need to add extra firewall rules. As A&A say:

    "RTP is the actual media (e.g., the audio). On our platform the RTP will
    come from the same call server IP address as the SIP control messages. " https://support.aa.net.uk/VoIP_Firewall

    so just the SIP ALG should be enough to make sure only packets from A&A's server make it back to your SIP device.

    So currently I have both port forwarding (with the above firewall
    rule) and SIP ALG and the phone rings OK.

    I think your additional firewall rules may be making the problem worse, particularly if they're taking priority over the ALG.

    Although that page talks about complications around having multiple SIP
    devices - the ALG can't tell which device the incoming connection is for.
    That could be a problem.

    Voipfone have a much cleaner system where their phones keep alive
    every 60s so not port forwarding or any other router config is needed.

    I think A&A do that too? SIP clients stay connected, they don't drop off through inaction. I haven't done a packet capture, but with Gigaset
    endpoints things 'just work'.

    I've used A&A on a variety of broadband connections with a variety of >provider routers (and double NAT through two routers), and at most it needed >the SIP ALG turning on in the router settings.

    Digging into this, it looks like A&A may have changed their server
    config:

    From Claude: If the router hasn?t changed, then the change was on the
    other side, so the provider is the likelier explanation. A typical
    candidate is how their servers handle NAT. Many SIP providers quietly
    correct for private addresses in the Contact and SDP headers, by
    replying to the address and port the packet actually came from. If
    they tightened or changed that behaviour, phones behind NAT without an
    ALG would stop working, and enabling the ALG would fix them, exactly
    as you saw.

    A&A would never admit that though ;)

    Did something change? If anything, I'd expect A&A not to 'quietly correct'
    - given their NAT stance they would rather the connection doesn't work so
    the user sorts it out properly, rather than silently enabling bad behaviour.

    I *am* concerned about security. AFAICT the inbound IP firewall rule
    prevents VOIP phone fraud, but if ALG allows incoming packets to
    bypass NAT, that is bad because they could be malformed.

    I'm not seeing how it's worse than any other kind of NAT? A NAT+firewall
    only let packets in if somebody inside initiated them. If they didn't, it blocks them.

    When you connect to www.example.com TCP port 443, the response is let through because you sent out the first packet. If somebody on the internet tries to send a packet to my web browser, it won't succeed unless there is an entry
    in the NAT table recording that a packet was previously sent to them.

    If you're adding firewall rules to this mix, they need to be in addition to rather than instead of the NAT rules. eg you add additional filtering so
    that www.example.com can only send packets back to me if the connection is
    to their port 443 (ie the rule is IF existing_connection AND dest_IP==104.20.23.154 AND dest_port==443). It doesn't allow
    www.example.com access any time to your LAN, which you'd get if skipping the 'existing_connection' check.

    The SIP ALG is just a hack on top of NAT so that it rewrites the addresses inside the SIP/RTP packets as well as rewriting the headers. It also allows outgoing SIP and incoming RTP traffic from the same host to share the same
    NAT table entry (so a incoming RTP connection is allowed after an outgoing SIP).

    (AIUI anyway)

    If you're using a STUN server, it's another way for clients to find out
    their public IPs which handles the first part (ie clients can embed the
    correct public IP in their packets), but it does not touch the firewall's
    NAT rules so incoming media wouldn't be accepted without the ALG rules.

    Wouldn't the best/simplest answer be to get IPV6 working? Then there is
    simply no issue with NAT.

    Yes, I think A&A assume you don't need NAT because they offer you IPv6. As >you're an A&A broadband customer you by definition have IPv6 on your >connection. It would seem to make sense to do the thing they offer support >for.

    I don't want to touch IPV6. I have other stuff set up which doesn't
    support it, and life is too short :)

    Other stuff can carry on using IPv4 oblivious to the presence of IPv6. It's pretty simple to enable and, if you let it do its thing, 'just works'. If
    you want to nail it down then that's more work.

    (or is the problem your home broadband is a different provider who doesn't >have IPv6? As above even IPv4 double-NAT has never been a problem for me)

    Yes my home fibre is Voipfone and that phone is on A&A.

    Voipfone can take over the office number and I am sure their system is
    much better (their support is certainly excellent) but the number
    would apparently go dead for 7 days, which is not acceptable. To avoid
    this, I would need to transfer the whole office to Voipfone but then I
    have to reconfig a lot of stuff - which I can do if needed.

    I suspect A&A will actually work for you fine and perhaps you have overcomplicated it which is the source of problem?

    Theo
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Richmond@dnomhcir@gmx.com to uk.telecom on Sat Oct 31 15:44:29 2026
    From Newsgroup: uk.telecom

    Postman Pat <at@the-post-office-not.com> writes:

    Almost a year later I am having to revisit this issue, and I am
    looking for recommendations.

    Maybe you could use a VPN to bypass all your local hazards directly into
    the office network? I don't know how you would do that exactly, maybe
    set up an old computer to VPN and plug the VOIP phone into the ethernet
    port.
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Postman Pat@at@the-post-office-not.com to uk.telecom on Tue Nov 3 13:48:36 2026
    From Newsgroup: uk.telecom

    Thank you :)

    I enabled SIP ALG, so that is in addition to 5060 forwarding to the
    phone's internal LAN IP (which is also fixed in the phone config) and
    the phone rings OK now.

    I still fail to see how SIP ALG *alone* can forward 5060 on incoming
    calls while allowing in only A&A IPs. This is a Draytek router without
    any remote or internal ("plug and play crap") config.

    If I get any more hassle I will move the whole lot to Voipfone.
    Simpler and non-arrogant... I am with them at another location and
    have had zero downtime in 3 years (fibre + Grandstream VOIP).




    Theo <theom+news@chiark.greenend.org.uk> wrote:

    Postman Pat <at@the-post-office-not.com> wrote:

    Theo <theom+news@chiark.greenend.org.uk> wrote:

    The SIP ALG should inspect the packets passing through the router and
    rewrite them with the correct public IP.

    I've been reading up on this.

    It seems that with ALG you do *not* enable port forwarding, and the
    router works out the phone's private IP by inspecting its *outgoing*
    (presumably keep-alive) packets. So if it gets a 5060 packet, it knows
    where to send it.

    But then I don't get the opportunity to enable the forwarding only
    from A&A IP ranges, which is obviously crucial otherwise all of china
    will be in there hammering port 5060 ;)

    I think the idea is that the SIP ALG sees a local device connecting to A&A >port 5060, and rewrites it with the public IP but also remembers the LAN IP. >When media connections come back from A&A to your router, the ALG knows to >forward them on to the phone's LAN IP.

    If somebody else sends you SIP or RTP traffic, it doesn't come from the A&A >IP and the ALG doesn't forward it, so the firewall dumps it.

    That means you don't need to add extra firewall rules. As A&A say:

    "RTP is the actual media (e.g., the audio). On our platform the RTP will >come from the same call server IP address as the SIP control messages. " >https://support.aa.net.uk/VoIP_Firewall

    so just the SIP ALG should be enough to make sure only packets from A&A's >server make it back to your SIP device.

    So currently I have both port forwarding (with the above firewall
    rule) and SIP ALG and the phone rings OK.

    I think your additional firewall rules may be making the problem worse, >particularly if they're taking priority over the ALG.

    Although that page talks about complications around having multiple SIP >devices - the ALG can't tell which device the incoming connection is for. >That could be a problem.

    Voipfone have a much cleaner system where their phones keep alive
    every 60s so not port forwarding or any other router config is needed.

    I think A&A do that too? SIP clients stay connected, they don't drop off >through inaction. I haven't done a packet capture, but with Gigaset >endpoints things 'just work'.

    I've used A&A on a variety of broadband connections with a variety of
    provider routers (and double NAT through two routers), and at most it needed
    the SIP ALG turning on in the router settings.

    Digging into this, it looks like A&A may have changed their server
    config:

    From Claude: If the router hasn?t changed, then the change was on the
    other side, so the provider is the likelier explanation. A typical
    candidate is how their servers handle NAT. Many SIP providers quietly
    correct for private addresses in the Contact and SDP headers, by
    replying to the address and port the packet actually came from. If
    they tightened or changed that behaviour, phones behind NAT without an
    ALG would stop working, and enabling the ALG would fix them, exactly
    as you saw.

    A&A would never admit that though ;)

    Did something change? If anything, I'd expect A&A not to 'quietly correct'
    - given their NAT stance they would rather the connection doesn't work so
    the user sorts it out properly, rather than silently enabling bad behaviour.

    I *am* concerned about security. AFAICT the inbound IP firewall rule
    prevents VOIP phone fraud, but if ALG allows incoming packets to
    bypass NAT, that is bad because they could be malformed.

    I'm not seeing how it's worse than any other kind of NAT? A NAT+firewall >only let packets in if somebody inside initiated them. If they didn't, it >blocks them.

    When you connect to www.example.com TCP port 443, the response is let through >because you sent out the first packet. If somebody on the internet tries to >send a packet to my web browser, it won't succeed unless there is an entry
    in the NAT table recording that a packet was previously sent to them.

    If you're adding firewall rules to this mix, they need to be in addition to >rather than instead of the NAT rules. eg you add additional filtering so >that www.example.com can only send packets back to me if the connection is
    to their port 443 (ie the rule is IF existing_connection AND >dest_IP==104.20.23.154 AND dest_port==443). It doesn't allow
    www.example.com access any time to your LAN, which you'd get if skipping the >'existing_connection' check.

    The SIP ALG is just a hack on top of NAT so that it rewrites the addresses >inside the SIP/RTP packets as well as rewriting the headers. It also allows >outgoing SIP and incoming RTP traffic from the same host to share the same >NAT table entry (so a incoming RTP connection is allowed after an outgoing >SIP).

    (AIUI anyway)

    If you're using a STUN server, it's another way for clients to find out
    their public IPs which handles the first part (ie clients can embed the >correct public IP in their packets), but it does not touch the firewall's
    NAT rules so incoming media wouldn't be accepted without the ALG rules.

    Wouldn't the best/simplest answer be to get IPV6 working? Then there is >> >> simply no issue with NAT.

    Yes, I think A&A assume you don't need NAT because they offer you IPv6. As >> >you're an A&A broadband customer you by definition have IPv6 on your
    connection. It would seem to make sense to do the thing they offer support >> >for.

    I don't want to touch IPV6. I have other stuff set up which doesn't
    support it, and life is too short :)

    Other stuff can carry on using IPv4 oblivious to the presence of IPv6. It's >pretty simple to enable and, if you let it do its thing, 'just works'. If >you want to nail it down then that's more work.

    (or is the problem your home broadband is a different provider who doesn't >> >have IPv6? As above even IPv4 double-NAT has never been a problem for me) >>
    Yes my home fibre is Voipfone and that phone is on A&A.

    Voipfone can take over the office number and I am sure their system is
    much better (their support is certainly excellent) but the number
    would apparently go dead for 7 days, which is not acceptable. To avoid
    this, I would need to transfer the whole office to Voipfone but then I
    have to reconfig a lot of stuff - which I can do if needed.

    I suspect A&A will actually work for you fine and perhaps you have >overcomplicated it which is the source of problem?

    Theo
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Theo@theom+news@chiark.greenend.org.uk to uk.telecom on Tue Nov 3 15:34:24 2026
    From Newsgroup: uk.telecom

    Postman Pat <at@the-post-office-not.com> wrote:
    Thank you :)

    I enabled SIP ALG, so that is in addition to 5060 forwarding to the
    phone's internal LAN IP (which is also fixed in the phone config) and
    the phone rings OK now.

    I still fail to see how SIP ALG *alone* can forward 5060 on incoming
    calls while allowing in only A&A IPs. This is a Draytek router without
    any remote or internal ("plug and play crap") config.

    Roughly speaking, although it may differ from vendor to vendor (and may do other stuff in addition):

    1. Phone on LAN makes outgoing connection to SIP server port 5060, saying it
    is available on RTP port range aaaa-bbbb.

    2. NAT rewrites the IP on the packet headers from phone's LAN IP to
    public IP, creates an entry in the NAT table to remember the state of this connection for its duration. (this is what NAT does for every connection)

    3. SIP ALG rewrites the IP address inside the SIP connection to be the
    public IP, not the LAN IP

    4. SIP ALG creates a temporary firewall rule to forward incoming RTP
    traffic from the SIP server's source IP to the phone's LAN IP, based on the ports described in the SIP connection

    5. Incoming audio: SIP server opens an RTP connection to the router in the appropriate port range, using the same source IP as the initial SIP
    connection.

    6. Using the temporary firewall rule, router forwards RTP traffic to the phone's LAN IP

    7. Phone receives and sends audio

    8. <phone call happens>

    9. Phone deregisters by closing SIP connection (perhaps it was turned off)

    10. Server closes RTP connection

    10. NAT drops NAT table entries for connections

    11. SIP ALG deletes temporary firewall rule

    Any point from 4 onwards if an attacker tries to connect, their source
    IP will not match the source IP in the temporary firewall rule and
    their connection will be blocked. Before point 4 they would be blocked by default.

    A key issue here is the temporary firewall rule in step 4 only works if this SIP server is talking to a single SIP endpoint on the LAN. If you have multiple SIP clients on the LAN then the firewall sees an incoming
    connection and has no means to identify which SIP client it is for,
    resulting in one way audio and/or no rings. That problem is solved by IPv6, but it's also solved by setting the RTP ports in each client to be
    different. That way the firewall knows that RTP to ports aaaa-bbbb goes to client 1 and cccc-dddd goes to client 2, ie you end up with two temporary firewall rules.

    (a separate one-way calling issue is clients on mobiles going to sleep and
    not being ready to receive the connection when a call is incoming, but
    that's not relevant here)

    If I get any more hassle I will move the whole lot to Voipfone.
    Simpler and non-arrogant... I am with them at another location and
    have had zero downtime in 3 years (fibre + Grandstream VOIP).

    I've had zero downtime with A&A VOIP in ~10 years... aside from the
    internet connection which they don't control.

    TBH, given how much of a hack the above is and the weird stuff the router vendor could be doing, which is impossible to packet-capture if it's also
    your DSL modem in the same ISP-locked-down box, I'm not surprised they would much rather you use IPv6 and have a limited time to debug IPv4 problems.

    I think a lot of it would also be solved if you're running the SIP client on the router, ie with a public IPv4, like most ISP boxes are running their own VOIP. Then you aren't putting it behind NAT and it all works sensibly. So
    a router with maybe a DECT base and an analogue socket avoids a lot of NAT issues, ie VOIP is never going over the LAN.

    That said, I've used A&A with Gigaset boxes behind numerous ISPs and it's
    'just worked'; the most I've had to do is turn on the SIP ALG setting in the ISP router.

    Theo
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Postman Pat@at@the-post-office-not.com to uk.telecom on Wed Nov 4 14:48:04 2026
    From Newsgroup: uk.telecom

    Thank you again. SIP ALG is a horrible hack.

    The bit I wondered about was

    4. SIP ALG creates a temporary firewall rule to forward incoming RTP
    traffic from the SIP server's source IP to the phone's LAN IP, based on the >ports described in the SIP connection

    which will work only if the VOIP server always uses the same IP. A&A
    gave me several IP ranges which I have set up in the NAT port
    forwarding.

    This, no SIP ALG config, worked for probably 2-3 years, and stopped
    only recently. So I have to wonder - what's changed??

    As an aside, I had *incoming* VOIP working with a Nokia 808 (year
    2014). Nokia were heavily into the corporate sphere and got this stuff
    working. The phone obviously had to keep-alive (I recall configuring a
    STUN server or some such). The weak link was the home wifi... Nowadays
    the phone companies sell "wifi calling" which does the same job.


    Theo <theom+news@chiark.greenend.org.uk> wrote:

    Postman Pat <at@the-post-office-not.com> wrote:
    Thank you :)

    I enabled SIP ALG, so that is in addition to 5060 forwarding to the
    phone's internal LAN IP (which is also fixed in the phone config) and
    the phone rings OK now.

    I still fail to see how SIP ALG *alone* can forward 5060 on incoming
    calls while allowing in only A&A IPs. This is a Draytek router without
    any remote or internal ("plug and play crap") config.

    Roughly speaking, although it may differ from vendor to vendor (and may do >other stuff in addition):

    1. Phone on LAN makes outgoing connection to SIP server port 5060, saying it >is available on RTP port range aaaa-bbbb.

    2. NAT rewrites the IP on the packet headers from phone's LAN IP to
    public IP, creates an entry in the NAT table to remember the state of this >connection for its duration. (this is what NAT does for every connection)

    3. SIP ALG rewrites the IP address inside the SIP connection to be the >public IP, not the LAN IP

    4. SIP ALG creates a temporary firewall rule to forward incoming RTP
    traffic from the SIP server's source IP to the phone's LAN IP, based on the >ports described in the SIP connection

    5. Incoming audio: SIP server opens an RTP connection to the router in the >appropriate port range, using the same source IP as the initial SIP >connection.

    6. Using the temporary firewall rule, router forwards RTP traffic to the >phone's LAN IP

    7. Phone receives and sends audio

    8. <phone call happens>

    9. Phone deregisters by closing SIP connection (perhaps it was turned off)

    10. Server closes RTP connection

    10. NAT drops NAT table entries for connections

    11. SIP ALG deletes temporary firewall rule

    Any point from 4 onwards if an attacker tries to connect, their source
    IP will not match the source IP in the temporary firewall rule and
    their connection will be blocked. Before point 4 they would be blocked by >default.

    A key issue here is the temporary firewall rule in step 4 only works if this >SIP server is talking to a single SIP endpoint on the LAN. If you have >multiple SIP clients on the LAN then the firewall sees an incoming
    connection and has no means to identify which SIP client it is for,
    resulting in one way audio and/or no rings. That problem is solved by IPv6, >but it's also solved by setting the RTP ports in each client to be
    different. That way the firewall knows that RTP to ports aaaa-bbbb goes to >client 1 and cccc-dddd goes to client 2, ie you end up with two temporary >firewall rules.

    (a separate one-way calling issue is clients on mobiles going to sleep and >not being ready to receive the connection when a call is incoming, but
    that's not relevant here)

    If I get any more hassle I will move the whole lot to Voipfone.
    Simpler and non-arrogant... I am with them at another location and
    have had zero downtime in 3 years (fibre + Grandstream VOIP).

    I've had zero downtime with A&A VOIP in ~10 years... aside from the
    internet connection which they don't control.

    TBH, given how much of a hack the above is and the weird stuff the router >vendor could be doing, which is impossible to packet-capture if it's also >your DSL modem in the same ISP-locked-down box, I'm not surprised they would >much rather you use IPv6 and have a limited time to debug IPv4 problems.

    I think a lot of it would also be solved if you're running the SIP client on >the router, ie with a public IPv4, like most ISP boxes are running their own >VOIP. Then you aren't putting it behind NAT and it all works sensibly. So
    a router with maybe a DECT base and an analogue socket avoids a lot of NAT >issues, ie VOIP is never going over the LAN.

    That said, I've used A&A with Gigaset boxes behind numerous ISPs and it's >'just worked'; the most I've had to do is turn on the SIP ALG setting in the >ISP router.

    Theo
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Theo@theom+news@chiark.greenend.org.uk to uk.telecom on Wed Nov 4 16:50:10 2026
    From Newsgroup: uk.telecom

    Postman Pat <at@the-post-office-not.com> wrote:
    Thank you again. SIP ALG is a horrible hack.

    The bit I wondered about was

    4. SIP ALG creates a temporary firewall rule to forward incoming RTP >traffic from the SIP server's source IP to the phone's LAN IP, based on the >ports described in the SIP connection

    which will work only if the VOIP server always uses the same IP. A&A
    gave me several IP ranges which I have set up in the NAT port
    forwarding.

    Yes. A&A say they do that:

    "On our platform the RTP will come from the same call server IP address as
    the SIP control messages."
    https://support.aa.net.uk/VoIP_Firewall

    Their server currently advertises multiple IPs:
    $ host voiceless.aa.net.uk
    voiceless.aa.net.uk has address 81.187.30.116
    voiceless.aa.net.uk has address 81.187.30.118
    voiceless.aa.net.uk has IPv6 address 2001:8b0:0:30::5060:1
    voiceless.aa.net.uk has IPv6 address 2001:8b0:0:30::5060:3

    but they're saying that when you pick one to connect to, the audio will come back from the same one.

    That also means that two phones behind the same NAT may work if one
    registers on .116 and the other on .118, as the SIP ALG can create distinct firewall rules for them, but if the round-robin DNS happens that they both
    land on the same IP then one may not work.

    You can see why there are so many variables they just don't want to get involved with debugging :-(

    This, no SIP ALG config, worked for probably 2-3 years, and stopped
    only recently. So I have to wonder - what's changed??

    Not sure. They do say that the IP range for firewalling purposes is broader than the IPs they publish in the DNS, which suggests they are free to change advertised IPs without needing changes at the customer end.

    As an aside, I had *incoming* VOIP working with a Nokia 808 (year
    2014). Nokia were heavily into the corporate sphere and got this stuff working. The phone obviously had to keep-alive (I recall configuring a
    STUN server or some such). The weak link was the home wifi... Nowadays
    the phone companies sell "wifi calling" which does the same job.

    Likewise I've found Gigaset fairly bulletproof. They actually don't have
    too many VOIP settings, which makes them easier to configure than the old
    PAP2T I used to use.

    Theo
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Richmond@dnomhcir@gmx.com to uk.telecom on Wed Nov 4 17:06:36 2026
    From Newsgroup: uk.telecom

    Theo <theom+news@chiark.greenend.org.uk> writes:


    That also means that two phones behind the same NAT may work if one
    registers on .116 and the other on .118, as the SIP ALG can create
    distinct firewall rules for them, but if the round-robin DNS happens
    that they both land on the same IP then one may not work.


    I don't know if it would help but I have two phones connected to the
    router, and in the settings on the router under SIP service provider, I
    have two different Outbound Proxy Ports, 5061 and 5062. SIP ALG is
    enabled. But the two phones use different VOIP providers, one uses AA
    the other uses Voipfone. It all seems to work.
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Theo@theom+news@chiark.greenend.org.uk to uk.telecom on Wed Nov 4 17:34:09 2026
    From Newsgroup: uk.telecom

    Richmond <dnomhcir@gmx.com> wrote:
    Theo <theom+news@chiark.greenend.org.uk> writes:


    That also means that two phones behind the same NAT may work if one registers on .116 and the other on .118, as the SIP ALG can create
    distinct firewall rules for them, but if the round-robin DNS happens
    that they both land on the same IP then one may not work.


    I don't know if it would help but I have two phones connected to the
    router, and in the settings on the router under SIP service provider, I
    have two different Outbound Proxy Ports, 5061 and 5062. SIP ALG is
    enabled. But the two phones use different VOIP providers, one uses AA
    the other uses Voipfone. It all seems to work.

    The problem is if both phones are talking to the same service provider IP. When the service provider IP wants to make a connection towards you, your router can't tell which phone to forward it to.

    If you have different service provider IPs (which you will using different companies), the router can use the source IP to work out which phone
    previously contacted that IP and so forward it correctly.

    ie if phone 1 last talked to the A&A server, then an incoming connection
    from the A&A server should be forwarded to phone 1. If phone 2 talked to
    the Voipfone server, incoming connections from Voipfone should go to phone
    2. But if phone 2 was also talking to the same A&A server, the router
    doesn't know whether to send the connection to phone 1 or phone 2.

    The wrinkle above is that the 'same server' may not actually be the same IP
    due to DNS load-balancing. If phone 1 is talking to .116 and phone 2 to
    .118 then the router can tell them apart and everything works. But if phone
    2 looked up voiceless.aa.net.uk and got .116 which phone 1 was already
    talking to, then the router can't tell them apart. Maybe by default it
    always sends the incoming connection to the first device it saw (phone 1),
    in which case phone 2 won't get incoming audio.

    There are lots of variables and if you can't packet-capture the WAN port of
    the router it's hard to work out what's happening.

    Theo
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Pancho@Pancho.Jones@protonmail.com to uk.telecom on Thu Nov 5 13:38:12 2026
    From Newsgroup: uk.telecom

    On 29/10/2026 12:56, Postman Pat wrote:

    I am all ears for any recommendations :)

    I, and many others here, used Sipgate for many years. The only thing
    they ever did wrong to me was stop offering the service I was using.

    If you are willing to pay, I would assume they still offer a good service
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Pancho@Pancho.Jones@protonmail.com to uk.telecom on Thu Nov 5 13:45:19 2026
    From Newsgroup: uk.telecom

    On 30/10/2026 12:08, Theo wrote:


    Yes, I think A&A assume you don't need NAT because they offer you IPv6. As you're an A&A broadband customer you by definition have IPv6 on your connection. It would seem to make sense to do the thing they offer support for.


    Yeahbut, my old hardware, Gigaset N300, A580, etc doesn't do IPv6.
    Did people here buy new hardware for VoIP IPv6? I'm at my son's house
    now, he has CGNAT, so I was forced to go IPv6 for some things, but A&A
    VoIP seems to work fine over CGNAT IPv4. (Caveat still early days)
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Woody@harrogate3@ntlworld.com to uk.telecom on Thu Nov 5 16:43:08 2026
    From Newsgroup: uk.telecom

    On Thu 05/11/2026 13:38, Pancho wrote:
    On 29/10/2026 12:56, Postman Pat wrote:

    I am all ears for any recommendations :)

    I, and many others here, used Sipgate for many years. The only thing
    they ever did wrong to me was stop offering the service I was using.

    If you are willing to pay, I would assume they still offer a good service


    I had several accounts with them, one was for comms with family
    (daughter) who only had a mobile. I still have the line I used at my end
    so that calls were free and it still works and is still free. Sadly all
    of the other lines have long since died.

    Has to be said that Sipgate were (and for me still are) very quick and
    helpful if I had/have any queries. What is more I used the lines with
    SPA2102 before they were Linksys, PAP2T when Linksys (and thence Cisco)
    bought them which worked and still work very well. The nice thing about Sipgate is that they use ports in the 40000 range which keeps them away
    from 5060 and up.
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Richmond@dnomhcir@gmx.com to uk.telecom on Fri Nov 6 12:53:52 2026
    From Newsgroup: uk.telecom

    Theo <theom+news@chiark.greenend.org.uk> writes:

    Richmond <dnomhcir@gmx.com> wrote:
    Theo <theom+news@chiark.greenend.org.uk> writes:


    That also means that two phones behind the same NAT may work if one
    registers on .116 and the other on .118, as the SIP ALG can create
    distinct firewall rules for them, but if the round-robin DNS
    happens that they both land on the same IP then one may not work.


    I don't know if it would help but I have two phones connected to the
    router, and in the settings on the router under SIP service provider,
    I have two different Outbound Proxy Ports, 5061 and 5062. SIP ALG is
    enabled. But the two phones use different VOIP providers, one uses AA
    the other uses Voipfone. It all seems to work.

    The problem is if both phones are talking to the same service provider
    IP. When the service provider IP wants to make a connection towards
    you, your router can't tell which phone to forward it to.

    If you have different service provider IPs (which you will using
    different companies), the router can use the source IP to work out
    which phone previously contacted that IP and so forward it correctly.

    ie if phone 1 last talked to the A&A server, then an incoming
    connection from the A&A server should be forwarded to phone 1. If
    phone 2 talked to the Voipfone server, incoming connections from
    Voipfone should go to phone 2. But if phone 2 was also talking to the
    same A&A server, the router doesn't know whether to send the
    connection to phone 1 or phone 2.

    The wrinkle above is that the 'same server' may not actually be the
    same IP due to DNS load-balancing. If phone 1 is talking to .116 and
    phone 2 to .118 then the router can tell them apart and everything
    works. But if phone 2 looked up voiceless.aa.net.uk and got .116
    which phone 1 was already talking to, then the router can't tell them
    apart. Maybe by default it always sends the incoming connection to
    the first device it saw (phone 1), in which case phone 2 won't get
    incoming audio.

    There are lots of variables and if you can't packet-capture the WAN
    port of the router it's hard to work out what's happening.

    Theo

    I've installed Linphone on an Amazon tablet and using this, I was able
    to phone my home phone number from my home phone number and leave a
    message. To get Linphone working though I had to disable IPv6. So I
    think this verifies that SIP ALG is kicking in with IPv4, but IPv6 is
    blocked by the firewall because I haven't set up any rules. It might be
    a good way to test things though.
    --- Synchronet 3.22a-Linux NewsLink 1.2