• VOIP phones

    From Scott@newsgroups@gefion.myzen.co.uk to uk.telecom on Thu Oct 15 21:19:57 2026
    From Newsgroup: uk.telecom

    I have a router beside my desk with a standard phone plugged into it.
    Do corded VOIP phones exist and would they offer any benefit?
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Brian Gregory@void-invalid-dead-dontuse@email.invalid to uk.telecom on Thu Oct 15 23:03:11 2026
    From Newsgroup: uk.telecom

    On 15/10/2026 21:19, Scott wrote:
    I have a router beside my desk with a standard phone plugged into it.
    Do corded VOIP phones exist and would they offer any benefit?

    Yes they do.
    I have two Snom D120 (wired) phones. (At present I only use one.
    Connecting more than one to a VoIP service designed for a single ATA is complicated)

    Sometimes using an analogue phone with any ATA (Analog Telephone
    Adapter) that allows an ordinary analogue phone to connect to VoIP
    results in poor sound and/or some echo which can mostly be avoided by
    using a VoIP phone.

    If you use a VoIP phone dialling from a memory will connect instantly,
    it often works more like using a mobile than an analogue phone so
    typically you enter or recall a number and press a GO or green or a tick
    (reU) button. Calling via an ATA usually takes a few seconds more than the time it takes the analogue phone to send the DTMF, because there is a
    usually a timeout to detect that you've stopped adding more digits to
    the number.

    However if you want to use a VoIP phone instead of an ISP provided ATA
    you'll need to find out the required settings for the phone and also how
    to disable the ATA in the router and configure it to pass the VoIP
    through to your VoIP phone.
    --
    Brian Gregory (in England).
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Woody@harrogate3@ntlworld.com to uk.telecom on Fri Oct 16 08:56:03 2026
    From Newsgroup: uk.telecom

    On Thu 15/10/2026 23:03, Brian Gregory wrote:
    On 15/10/2026 21:19, Scott wrote:
    I have a router beside my desk with a standard phone plugged into it.
    Do corded VOIP phones exist and would they offer any benefit?

    Yes they do.
    I have two Snom D120 (wired) phones. (At present I only use one.
    Connecting more than one to a VoIP service designed for a single ATA is complicated)

    Sometimes using an analogue phone with any ATA (Analog Telephone
    Adapter) that allows an ordinary analogue phone to connect to VoIP
    results in poor sound and/or some echo which can mostly be avoided by
    using a VoIP phone.

    If you use a VoIP phone dialling from a memory will connect instantly,
    it often works more like using a mobile than an analogue phone so
    typically you enter or recall a number and press a GO or green or a tick (reU) button. Calling via an ATA usually takes a few seconds more than the time it takes the analogue phone to send the DTMF, because there is a usually a timeout to detect that you've stopped adding more digits to
    the number.

    However if you want to use a VoIP phone instead of an ISP provided ATA you'll need to find out the required settings for the phone and also how
    to disable the ATA in the router and configure it to pass the VoIP
    through to your VoIP phone.


    I have a Panasonic desktop VoIP phone which works a treat - or rather it
    did when I installed it for my late f-in-l. I also have a couple of
    Linksys PAP2T or SPA2102 ATA's with which I have had no problem - save
    that whilst we were away earlier this year the PSU expired and something
    it did faulted the ATA - I could receive calls but if I wanted to make a
    call I only got a single tone instead of a proper dial tome.

    Other VoIP phones are such as Yealink/YeaStar, Grandstream (who also do
    ATAs) and D-Link. For set-up parameters just look at a few VoIP service providers and if necessary ring them and ask if they will supply
    operating parameters so you can used your own ATA - IME many will.


    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From David Wade@g4ugm@dave.invalid to uk.telecom on Fri Oct 16 09:26:04 2026
    From Newsgroup: uk.telecom

    On 15/10/2026 23:03, Brian Gregory wrote:
    On 15/10/2026 21:19, Scott wrote:
    I have a router beside my desk with a standard phone plugged into it.
    Do corded VOIP phones exist and would they offer any benefit?


    If you mean a device plugs into the local LAN and talks VOIP yes these
    exist. However they can't be used with EE ot BT routers as these are
    locked down.

    Yes they do.
    I have two Snom D120 (wired) phones. (At present I only use one.
    Connecting more than one to a VoIP service designed for a single ATA is complicated)


    You might want to look at a used Fritz!Box router with VOIP as they can
    act as a SIP server and mini PABX. You can of course also run Asterisk
    on a PI or similar.


    Sometimes using an analogue phone with any ATA (Analog Telephone
    Adapter) that allows an ordinary analogue phone to connect to VoIP
    results in poor sound and/or some echo which can mostly be avoided by
    using a VoIP phone.

    If you use a VoIP phone dialling from a memory will connect instantly,
    it often works more like using a mobile than an analogue phone so
    typically you enter or recall a number and press a GO or green or a tick (reU) button. Calling via an ATA usually takes a few seconds more than the time it takes the analogue phone to send the DTMF, because there is a usually a timeout to detect that you've stopped adding more digits to
    the number.

    However if you want to use a VoIP phone instead of an ISP provided ATA you'll need to find out the required settings for the phone and also how
    to disable the ATA in the router and configure it to pass the VoIP
    through to your VoIP phone.

    It depends on the router and VOIP service. So if its a BT or EE router
    you are locked into BT devices and can't add a "corded" SIP phone.

    If its a Fritz!box from ZEN that can act as a SIP server and mini PABX.
    So by having multiple SIP phones connected by Ethernet you can have your
    own internal phone system with extension dialing. As its also a DECT
    base station you can do the same with DECT

    Dave
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Richmond@dnomhcir@gmx.com to uk.telecom on Fri Oct 16 10:05:38 2026
    From Newsgroup: uk.telecom

    Brian Gregory <void-invalid-dead-dontuse@email.invalid> writes:


    Sometimes using an analogue phone with any ATA (Analog Telephone
    Adapter) that allows an ordinary analogue phone to connect to VoIP
    results in poor sound and/or some echo which can mostly be avoided by
    using a VoIP phone.


    Does the sound quality of VOIP depend on the ISPs network and the
    compression protocol it accepts? and also the recipients network.
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Chris Green@cl@isbd.net to uk.telecom on Fri Oct 16 10:06:15 2026
    From Newsgroup: uk.telecom

    Woody <harrogate3@ntlworld.com> wrote:
    On Thu 15/10/2026 23:03, Brian Gregory wrote:
    On 15/10/2026 21:19, Scott wrote:
    I have a router beside my desk with a standard phone plugged into it.
    Do corded VOIP phones exist and would they offer any benefit?

    Yes they do.
    I have two Snom D120 (wired) phones. (At present I only use one. Connecting more than one to a VoIP service designed for a single ATA is complicated)

    Sometimes using an analogue phone with any ATA (Analog Telephone
    Adapter) that allows an ordinary analogue phone to connect to VoIP
    results in poor sound and/or some echo which can mostly be avoided by using a VoIP phone.

    If you use a VoIP phone dialling from a memory will connect instantly,
    it often works more like using a mobile than an analogue phone so typically you enter or recall a number and press a GO or green or a tick (reU) button. Calling via an ATA usually takes a few seconds more than the time it takes the analogue phone to send the DTMF, because there is a usually a timeout to detect that you've stopped adding more digits to
    the number.

    However if you want to use a VoIP phone instead of an ISP provided ATA you'll need to find out the required settings for the phone and also how to disable the ATA in the router and configure it to pass the VoIP
    through to your VoIP phone.


    I have a Panasonic desktop VoIP phone which works a treat - or rather it
    did when I installed it for my late f-in-l. I also have a couple of
    Linksys PAP2T or SPA2102 ATA's with which I have had no problem - save
    that whilst we were away earlier this year the PSU expired and something
    it did faulted the ATA - I could receive calls but if I wanted to make a call I only got a single tone instead of a proper dial tome.

    Other VoIP phones are such as Yealink/YeaStar, Grandstream (who also do ATAs) and D-Link. For set-up parameters just look at a few VoIP service providers and if necessary ring them and ask if they will supply
    operating parameters so you can used your own ATA - IME many will.

    You can get secondhand Yealink VOIP phones very cheaply. I bought a
    Yealink SIP-T42S for about -u15 a while ago on eBay and it works very
    nicely.
    --
    Chris Green
    -+
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Marco Moock@mm@dorfdsl.de to uk.telecom on Fri Oct 16 11:49:50 2026
    From Newsgroup: uk.telecom

    Am 16.10.26 um 11:05 schrieb Richmond:
    Does the sound quality of VOIP depend on the ISPs network and the
    compression protocol it accepts? and also the recipients network.

    Of course. There are different codecs and your ISP might convert them if needed.

    The recipient's device and used codec is also relevant, as the lowest
    standard will define the speech quality.
    --
    Gru|f
    Marco

    Spam bitte an abfalleimer2001@stinkedores.dorfdsl.de
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From The Natural Philosopher@tnp@invalid.invalid to uk.telecom on Fri Oct 16 11:53:59 2026
    From Newsgroup: uk.telecom

    On 15/10/2026 21:19, Scott wrote:
    I have a router beside my desk with a standard phone plugged into it.
    Do corded VOIP phones exist and would they offer any benefit?

    ? what is a corded voip phone -+

    I have a PABX plugged into my VOIP router ports.
    --
    rCLThose who can make you believe absurdities, can make you commit atrocities.rCY

    rCo Voltaire, Questions sur les Miracles |a M. Claparede, Professeur de Th|-ologie |a Gen|?ve, par un Proposant: Ou Extrait de Diverses Lettres de
    M. de Voltaire

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From The Natural Philosopher@tnp@invalid.invalid to uk.telecom on Fri Oct 16 11:58:33 2026
    From Newsgroup: uk.telecom

    On 16/10/2026 10:05, Richmond wrote:
    Brian Gregory <void-invalid-dead-dontuse@email.invalid> writes:


    Sometimes using an analogue phone with any ATA (Analog Telephone
    Adapter) that allows an ordinary analogue phone to connect to VoIP
    results in poor sound and/or some echo which can mostly be avoided by
    using a VoIP phone.


    Does the sound quality of VOIP depend on the ISPs network and the
    compression protocol it accepts? and also the recipients network.

    IME with first Cisco and then Draytek routers with VOIP ports, the only degradation below 'better than POTS by a large margin' was packet loss
    causing breakup and distortion when my (now ex) wife was watching a
    video across the internet and I was downloading a software update. On ADSL

    In all cases it was way better than a crackly landline
    --
    rCLThose who can make you believe absurdities, can make you commit atrocities.rCY

    rCo Voltaire, Questions sur les Miracles |a M. Claparede, Professeur de Th|-ologie |a Gen|?ve, par un Proposant: Ou Extrait de Diverses Lettres de
    M. de Voltaire

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From The Natural Philosopher@tnp@invalid.invalid to uk.telecom on Fri Oct 16 12:03:23 2026
    From Newsgroup: uk.telecom

    On 16/10/2026 10:49, Marco Moock wrote:
    Am 16.10.26 um 11:05 schrieb Richmond:
    Does the sound quality of VOIP depend on the ISPs network and the
    compression protocol it accepts? and also the recipients network.

    Of course. There are different codecs and your ISP might convert them if needed.

    The ISP is not involved in inspeccting packets passing through it or
    changing their protocols.

    The codecs in use are a function of the endpoints, which are other VOIP
    phones

    VOIP has NOTHING to do with the ISP at all. Unless they are running
    their own SIP server and/or POTS gateway

    Or shuffling packet queus based on whether there is a viOPp packet in them


    The recipient's device and used codec is also relevant, as the lowest standard will define the speech quality.


    That is ALL that is relevant, that and the bandwidth, packet loss and
    latency between the devices

    None of which is necessaruly ISP specific
    --
    In a Time of Universal Deceit, Telling the Truth Is a Revolutionary Act.

    - George Orwell

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Andy Burns@usenet@andyburns.uk to uk.telecom on Fri Oct 16 12:05:54 2026
    From Newsgroup: uk.telecom

    The Natural Philosopher wrote:

    VOIP has NOTHING to do with the ISP at all. Unless they are running
    their own SIP server and/or POTS gateway

    I think you're right to assume that most ISPs outsource the VoIP, but
    not all do (e.g. AAISP)

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Richmond@dnomhcir@gmx.com to uk.telecom on Fri Oct 16 12:30:40 2026
    From Newsgroup: uk.telecom

    Andy Burns <usenet@andyburns.uk> writes:

    The Natural Philosopher wrote:

    VOIP has NOTHING to do with the ISP at all. Unless they are running
    their own SIP server and/or POTS gateway

    I think you're right to assume that most ISPs outsource the VoIP, but
    not all do (e.g. AAISP)

    I am with AAISP. But I see Voipfone is also an ISP. And anyone who runs
    a SIP registrar/proxy to handle registration and call routing is
    technically an ISP.
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Scott@newsgroups@gefion.myzen.co.uk to uk.telecom on Fri Oct 16 12:57:36 2026
    From Newsgroup: uk.telecom

    On Fri, 16 Oct 2026 11:58:33 +0100, The Natural Philosopher <tnp@invalid.invalid> wrote:

    On 16/10/2026 10:05, Richmond wrote:
    Brian Gregory <void-invalid-dead-dontuse@email.invalid> writes:


    Sometimes using an analogue phone with any ATA (Analog Telephone
    Adapter) that allows an ordinary analogue phone to connect to VoIP
    results in poor sound and/or some echo which can mostly be avoided by
    using a VoIP phone.


    Does the sound quality of VOIP depend on the ISPs network and the
    compression protocol it accepts? and also the recipients network.

    IME with first Cisco and then Draytek routers with VOIP ports, the only >degradation below 'better than POTS by a large margin' was packet loss >causing breakup and distortion when my (now ex) wife was watching a
    video

    A situation you obviously dealt with decisively :-)
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Scott@newsgroups@gefion.myzen.co.uk to uk.telecom on Fri Oct 16 13:03:59 2026
    From Newsgroup: uk.telecom

    On Fri, 16 Oct 2026 09:26:04 +0100, David Wade <g4ugm@dave.invalid>
    wrote:

    On 15/10/2026 23:03, Brian Gregory wrote:
    On 15/10/2026 21:19, Scott wrote:
    I have a router beside my desk with a standard phone plugged into it.
    Do corded VOIP phones exist and would they offer any benefit?


    If you mean a device plugs into the local LAN and talks VOIP yes these >exist. However they can't be used with EE ot BT routers as these are
    locked down.

    Yes they do.
    I have two Snom D120 (wired) phones. (At present I only use one.
    Connecting more than one to a VoIP service designed for a single ATA is
    complicated)


    You might want to look at a used Fritz!Box router with VOIP as they can
    act as a SIP server and mini PABX. You can of course also run Asterisk
    on a PI or similar.


    Sometimes using an analogue phone with any ATA (Analog Telephone
    Adapter) that allows an ordinary analogue phone to connect to VoIP
    results in poor sound and/or some echo which can mostly be avoided by
    using a VoIP phone.

    If you use a VoIP phone dialling from a memory will connect instantly,
    it often works more like using a mobile than an analogue phone so
    typically you enter or recall a number and press a GO or green or a tick
    (?) button. Calling via an ATA usually takes a few seconds more than the
    time it takes the analogue phone to send the DTMF, because there is a
    usually a timeout to detect that you've stopped adding more digits to
    the number.

    However if you want to use a VoIP phone instead of an ISP provided ATA
    you'll need to find out the required settings for the phone and also how
    to disable the ATA in the router and configure it to pass the VoIP
    through to your VoIP phone.

    It depends on the router and VOIP service. So if its a BT or EE router
    you are locked into BT devices and can't add a "corded" SIP phone.

    If its a Fritz!box from ZEN that can act as a SIP server and mini PABX.
    So by having multiple SIP phones connected by Ethernet you can have your
    own internal phone system with extension dialing. As its also a DECT
    base station you can do the same with DECT

    As it happens, it is a FRITZ!Box and Zen is my ISP. Does this mean I
    can plug it into a LAN port (not FON) and will it work out of the box?
    Does SIP phone require a power supply?
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Brian Gregory@void-invalid-dead-dontuse@email.invalid to uk.telecom on Fri Oct 16 15:42:53 2026
    From Newsgroup: uk.telecom

    On 16/10/2026 12:03, The Natural Philosopher wrote:
    VOIP has NOTHING to do with the ISP at all. Unless they are running
    their own SIP server and/or POTS gateway

    Which obviously they are, since his analogue phone was plugged into his router.


    Or shuffling packet queues based on whether there is a VoIP packet in them
    (typos in above line corrected)

    Which ISPs that run their own VoIP do do, otherwise the VoIP would not
    be reliable when the internet was being used for a big download. It's up
    to your router to allow outgoing VoIP to jump the queue when a big
    upload is in progress.

    (Big here just means enough data is flowing to "max out" your connection)


    The recipient's device and used codec is also relevant, as the lowest
    standard will define the speech quality.


    That is ALL that is relevant, that and the bandwidth, packet loss-a and latency between the devices

    None of which is necessaruly ISP specific

    A lot of it *is* mostly dependant on the VoIP service and ISP you use.
    --
    Brian Gregory (in England).
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From David Wade@g4ugm@dave.invalid to uk.telecom on Fri Oct 16 15:44:21 2026
    From Newsgroup: uk.telecom

    On 16/10/2026 13:03, Scott wrote:
    On Fri, 16 Oct 2026 09:26:04 +0100, David Wade <g4ugm@dave.invalid>
    wrote:

    On 15/10/2026 23:03, Brian Gregory wrote:
    On 15/10/2026 21:19, Scott wrote:
    I have a router beside my desk with a standard phone plugged into it.
    Do corded VOIP phones exist and would they offer any benefit?


    If you mean a device plugs into the local LAN and talks VOIP yes these
    exist. However they can't be used with EE ot BT routers as these are
    locked down.

    Yes they do.
    I have two Snom D120 (wired) phones. (At present I only use one.
    Connecting more than one to a VoIP service designed for a single ATA is
    complicated)


    You might want to look at a used Fritz!Box router with VOIP as they can
    act as a SIP server and mini PABX. You can of course also run Asterisk
    on a PI or similar.


    Sometimes using an analogue phone with any ATA (Analog Telephone
    Adapter) that allows an ordinary analogue phone to connect to VoIP
    results in poor sound and/or some echo which can mostly be avoided by
    using a VoIP phone.

    If you use a VoIP phone dialling from a memory will connect instantly,
    it often works more like using a mobile than an analogue phone so
    typically you enter or recall a number and press a GO or green or a tick >>> (?) button. Calling via an ATA usually takes a few seconds more than the >>> time it takes the analogue phone to send the DTMF, because there is a
    usually a timeout to detect that you've stopped adding more digits to
    the number.

    However if you want to use a VoIP phone instead of an ISP provided ATA
    you'll need to find out the required settings for the phone and also how >>> to disable the ATA in the router and configure it to pass the VoIP
    through to your VoIP phone.

    It depends on the router and VOIP service. So if its a BT or EE router
    you are locked into BT devices and can't add a "corded" SIP phone.

    If its a Fritz!box from ZEN that can act as a SIP server and mini PABX.
    So by having multiple SIP phones connected by Ethernet you can have your
    own internal phone system with extension dialing. As its also a DECT
    base station you can do the same with DECT

    As it happens, it is a FRITZ!Box and Zen is my ISP. Does this mean I
    can plug it into a LAN port (not FON) and will it work out of the box?
    Does SIP phone require a power supply?

    No it needs to be configured both in the Fritz!Box and in the phone.
    Just check if you go to Telephony-> Devices in the Fritz you can add a
    device and add a network telephone.

    Then you put the details from that page into the phone.

    They do need power and as the Fritz does not do power over Ethernet
    sadly its another wall wart.

    There are also various options for an address book.

    Dave






    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Brian Gregory@void-invalid-dead-dontuse@email.invalid to uk.telecom on Fri Oct 16 16:04:02 2026
    From Newsgroup: uk.telecom

    On 16/10/2026 13:03, Scott wrote:
    As it happens, it is a FRITZ!Box and Zen is my ISP. Does this mean I
    can plug it into a LAN port (not FON) and will it work out of the box?
    Does SIP phone require a power supply?

    I'm with Zen.

    But I'm not using the Fritzbox. I couldn't cope with the weird names
    they call things that are presumably simplistic translations of their
    German names. But now I suspect my setup is also more complicated than
    the Fritzbox is capable of.

    Zen's, rather limited, information on setting up your own VoIP device is
    here:
    https://www.zen.co.uk/help-support/general-sip-settings/

    I set mine up using info in a blog I found before I knew about that page
    and I used UDP ports 10000-20000 for RTP while Zen says "Media Call
    Audio Addresses Ports - 20000 to 30000 UDP" so I guess you can actually
    use whatever you want in that case. Also it did seem to be easy enough
    to get it to work without port forwarding those ports, but I chose to
    port forward, but only UDP from Zen's VoIP servers (62.3.88.0/27).

    Also note that the Fritzbox provides some of the service like the
    answering machine which you won't get on Zen with most VoIP phones.
    --
    Brian Gregory (in England).
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Andy Burns@usenet@andyburns.uk to uk.telecom on Fri Oct 16 16:31:11 2026
    From Newsgroup: uk.telecom

    Brian Gregory wrote:

    The Natural Philosopher wrote:
    VOIP has NOTHING to do with the ISP at all. Unless they are running
    their own SIP server and/or POTS gateway

    Which obviously they are, since his analogue phone was plugged into his router.
    More likely the router separates off the VoIP traffic, and sends it to
    servers operated by (guessing) BT or Magrathea
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Scott@newsgroups@gefion.myzen.co.uk to uk.telecom on Fri Oct 16 16:40:29 2026
    From Newsgroup: uk.telecom

    On Fri, 16 Oct 2026 16:04:02 +0100, Brian Gregory <void-invalid-dead-dontuse@email.invalid> wrote:

    On 16/10/2026 13:03, Scott wrote:
    As it happens, it is a FRITZ!Box and Zen is my ISP. Does this mean I
    can plug it into a LAN port (not FON) and will it work out of the box?
    Does SIP phone require a power supply?

    I'm with Zen.

    But I'm not using the Fritzbox. I couldn't cope with the weird names
    they call things that are presumably simplistic translations of their
    German names. But now I suspect my setup is also more complicated than
    the Fritzbox is capable of.

    Zen's, rather limited, information on setting up your own VoIP device is >here:
    https://www.zen.co.uk/help-support/general-sip-settings/

    I set mine up using info in a blog I found before I knew about that page
    and I used UDP ports 10000-20000 for RTP while Zen says "Media Call
    Audio Addresses Ports - 20000 to 30000 UDP" so I guess you can actually
    use whatever you want in that case. Also it did seem to be easy enough
    to get it to work without port forwarding those ports, but I chose to
    port forward, but only UDP from Zen's VoIP servers (62.3.88.0/27).

    Also note that the Fritzbox provides some of the service like the
    answering machine which you won't get on Zen with most VoIP phones.

    I don't know if this helps or hinders but I already have a cordless
    VOIP phone (FRITZ!Fon) that links direct to the router (so I assume
    the basic set-up is in place). Now I am thinking about a corded VOIP
    (SIP) phone for my desk as the audio quality is not too good on the
    traditional phone I am using.
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Brian Gregory@void-invalid-dead-dontuse@email.invalid to uk.telecom on Fri Oct 16 17:12:09 2026
    From Newsgroup: uk.telecom

    On 16/10/2026 16:31, Andy Burns wrote:
    Brian Gregory wrote:

    The Natural Philosopher wrote:
    VOIP has NOTHING to do with the ISP at all. Unless they are running
    their own SIP server and/or POTS gateway

    Which obviously they are, since his analogue phone was plugged into
    his router.
    More likely the router separates off the VoIP traffic, and sends it to servers operated by (guessing) BT or Magrathea

    The reverse lookups of the IPs used are Zen names even if I don't use
    Zen's DNS, which I don't.
    --
    Brian Gregory (in England).
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Brian Gregory@void-invalid-dead-dontuse@email.invalid to uk.telecom on Fri Oct 16 17:15:34 2026
    From Newsgroup: uk.telecom

    On 16/10/2026 17:12, Brian Gregory wrote:
    On 16/10/2026 16:31, Andy Burns wrote:
    Brian Gregory wrote:

    The Natural Philosopher wrote:
    VOIP has NOTHING to do with the ISP at all. Unless they are running
    their own SIP server and/or POTS gateway

    Which obviously they are, since his analogue phone was plugged into
    his router.
    More likely the router separates off the VoIP traffic, and sends it to
    servers operated by (guessing) BT or Magrathea

    The reverse lookups of the IPs used are Zen names even if I don't use
    Zen's DNS, which I don't.

    But, come to think of it, I guess they could represent equipment
    provided by BT or Magrathea that's connected directly into Zen's networks.
    --
    Brian Gregory (in England).
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Brian Gregory@void-invalid-dead-dontuse@email.invalid to uk.telecom on Fri Oct 16 17:16:52 2026
    From Newsgroup: uk.telecom

    On 16/10/2026 16:40, Scott wrote:
    I don't know if this helps or hinders but I already have a cordless
    VOIP phone (FRITZ!Fon) that links direct to the router (so I assume
    the basic set-up is in place). Now I am thinking about a corded VOIP
    (SIP) phone for my desk as the audio quality is not too good on the traditional phone I am using.

    You will need Fritzbox documentation to find out about configuring a
    VoIP phone to connect to and use the Fritzbox as a kind of switchboard
    rather than to connect directly to Zen.
    --
    Brian Gregory (in England).
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Scott@newsgroups@gefion.myzen.co.uk to uk.telecom on Fri Oct 16 17:37:08 2026
    From Newsgroup: uk.telecom

    On Fri, 16 Oct 2026 17:16:52 +0100, Brian Gregory <void-invalid-dead-dontuse@email.invalid> wrote:

    On 16/10/2026 16:40, Scott wrote:
    I don't know if this helps or hinders but I already have a cordless
    VOIP phone (FRITZ!Fon) that links direct to the router (so I assume
    the basic set-up is in place). Now I am thinking about a corded VOIP
    (SIP) phone for my desk as the audio quality is not too good on the
    traditional phone I am using.

    You will need Fritzbox documentation to find out about configuring a
    VoIP phone to connect to and use the Fritzbox as a kind of switchboard >rather than to connect directly to Zen.

    Why can't it be connected in the same way as the FRITZ!Fon? Is SIP the
    same as VOIP?
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Andy Burns@usenet@andyburns.uk to uk.telecom on Fri Oct 16 17:41:53 2026
    From Newsgroup: uk.telecom

    Scott wrote:

    Why can't it be connected in the same way as the FRITZ!Fon? Is SIP the
    same as VOIP?

    Basically yes ... SIP is the signalling protocol and RTP is used for the actual audio/video.
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From David Wade@g4ugm@dave.invalid to uk.telecom on Fri Oct 16 17:59:35 2026
    From Newsgroup: uk.telecom

    On 16/10/2026 16:40, Scott wrote:
    On Fri, 16 Oct 2026 16:04:02 +0100, Brian Gregory <void-invalid-dead-dontuse@email.invalid> wrote:

    On 16/10/2026 13:03, Scott wrote:
    As it happens, it is a FRITZ!Box and Zen is my ISP. Does this mean I
    can plug it into a LAN port (not FON) and will it work out of the box?
    Does SIP phone require a power supply?

    I'm with Zen.

    But I'm not using the Fritzbox. I couldn't cope with the weird names
    they call things that are presumably simplistic translations of their
    German names. But now I suspect my setup is also more complicated than
    the Fritzbox is capable of.

    Zen's, rather limited, information on setting up your own VoIP device is
    here:
    https://www.zen.co.uk/help-support/general-sip-settings/

    I set mine up using info in a blog I found before I knew about that page
    and I used UDP ports 10000-20000 for RTP while Zen says "Media Call
    Audio Addresses Ports - 20000 to 30000 UDP" so I guess you can actually
    use whatever you want in that case. Also it did seem to be easy enough
    to get it to work without port forwarding those ports, but I chose to
    port forward, but only UDP from Zen's VoIP servers (62.3.88.0/27).

    Also note that the Fritzbox provides some of the service like the
    answering machine which you won't get on Zen with most VoIP phones.

    I don't know if this helps or hinders but I already have a cordless
    VOIP phone (FRITZ!Fon) that links direct to the router (so I assume
    the basic set-up is in place). Now I am thinking about a corded VOIP
    (SIP) phone for my desk as the audio quality is not too good on the traditional phone I am using.

    Personally I would try a DECT phone linked to the Fritz!box DECT Base. I
    have a Panasonic linked direct to my FritzBox and I think the call
    quality is better than the IP Phone I tried. You can do some tweaking of
    the audio in the Fritz...

    Dave
    p.s. this model

    https://www.ebay.co.uk/itm/237126660958

    Dave
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Scott@newsgroups@gefion.myzen.co.uk to uk.telecom on Fri Oct 16 18:41:10 2026
    From Newsgroup: uk.telecom

    On Fri, 16 Oct 2026 17:59:35 +0100, David Wade <g4ugm@dave.invalid>
    wrote:

    On 16/10/2026 16:40, Scott wrote:
    On Fri, 16 Oct 2026 16:04:02 +0100, Brian Gregory
    <void-invalid-dead-dontuse@email.invalid> wrote:

    On 16/10/2026 13:03, Scott wrote:
    As it happens, it is a FRITZ!Box and Zen is my ISP. Does this mean I
    can plug it into a LAN port (not FON) and will it work out of the box? >>>> Does SIP phone require a power supply?

    I'm with Zen.

    But I'm not using the Fritzbox. I couldn't cope with the weird names
    they call things that are presumably simplistic translations of their
    German names. But now I suspect my setup is also more complicated than
    the Fritzbox is capable of.

    Zen's, rather limited, information on setting up your own VoIP device is >>> here:
    https://www.zen.co.uk/help-support/general-sip-settings/

    I set mine up using info in a blog I found before I knew about that page >>> and I used UDP ports 10000-20000 for RTP while Zen says "Media Call
    Audio Addresses Ports - 20000 to 30000 UDP" so I guess you can actually
    use whatever you want in that case. Also it did seem to be easy enough
    to get it to work without port forwarding those ports, but I chose to
    port forward, but only UDP from Zen's VoIP servers (62.3.88.0/27).

    Also note that the Fritzbox provides some of the service like the
    answering machine which you won't get on Zen with most VoIP phones.

    I don't know if this helps or hinders but I already have a cordless
    VOIP phone (FRITZ!Fon) that links direct to the router (so I assume
    the basic set-up is in place). Now I am thinking about a corded VOIP
    (SIP) phone for my desk as the audio quality is not too good on the
    traditional phone I am using.

    Personally I would try a DECT phone linked to the Fritz!box DECT Base. I >have a Panasonic linked direct to my FritzBox and I think the call
    quality is better than the IP Phone I tried. You can do some tweaking of
    the audio in the Fritz...

    Dave
    p.s. this model

    https://www.ebay.co.uk/itm/237126660958

    Why would a DECT phone linked to the FRITZ!Box be better that a corded
    phone linked to the FRITZ!Box?
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From David Wade@g4ugm@dave.invalid to uk.telecom on Fri Oct 16 18:55:12 2026
    From Newsgroup: uk.telecom

    On 16/10/2026 18:41, Scott wrote:
    On Fri, 16 Oct 2026 17:59:35 +0100, David Wade <g4ugm@dave.invalid>
    wrote:

    On 16/10/2026 16:40, Scott wrote:
    On Fri, 16 Oct 2026 16:04:02 +0100, Brian Gregory
    <void-invalid-dead-dontuse@email.invalid> wrote:

    On 16/10/2026 13:03, Scott wrote:
    As it happens, it is a FRITZ!Box and Zen is my ISP. Does this mean I >>>>> can plug it into a LAN port (not FON) and will it work out of the box? >>>>> Does SIP phone require a power supply?

    I'm with Zen.

    But I'm not using the Fritzbox. I couldn't cope with the weird names
    they call things that are presumably simplistic translations of their
    German names. But now I suspect my setup is also more complicated than >>>> the Fritzbox is capable of.

    Zen's, rather limited, information on setting up your own VoIP device is >>>> here:
    https://www.zen.co.uk/help-support/general-sip-settings/

    I set mine up using info in a blog I found before I knew about that page >>>> and I used UDP ports 10000-20000 for RTP while Zen says "Media Call
    Audio Addresses Ports - 20000 to 30000 UDP" so I guess you can actually >>>> use whatever you want in that case. Also it did seem to be easy enough >>>> to get it to work without port forwarding those ports, but I chose to
    port forward, but only UDP from Zen's VoIP servers (62.3.88.0/27).

    Also note that the Fritzbox provides some of the service like the
    answering machine which you won't get on Zen with most VoIP phones.

    I don't know if this helps or hinders but I already have a cordless
    VOIP phone (FRITZ!Fon) that links direct to the router (so I assume
    the basic set-up is in place). Now I am thinking about a corded VOIP
    (SIP) phone for my desk as the audio quality is not too good on the
    traditional phone I am using.

    Personally I would try a DECT phone linked to the Fritz!box DECT Base. I
    have a Panasonic linked direct to my FritzBox and I think the call
    quality is better than the IP Phone I tried. You can do some tweaking of
    the audio in the Fritz...

    Dave
    p.s. this model

    https://www.ebay.co.uk/itm/237126660958

    Why would a DECT phone linked to the FRITZ!Box be better that a corded
    phone linked to the FRITZ!Box?

    Because many corded phones are pretty naff.

    Dave
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Brian Gregory@void-invalid-dead-dontuse@email.invalid to uk.telecom on Fri Oct 16 19:27:21 2026
    From Newsgroup: uk.telecom

    On 16/10/2026 18:55, David Wade wrote:
    On 16/10/2026 18:41, Scott wrote:
    On Fri, 16 Oct 2026 17:59:35 +0100, David Wade <g4ugm@dave.invalid>
    wrote:
    Why would a DECT phone linked to the FRITZ!Box be better that a corded
    phone linked to the FRITZ!Box?

    Because many corded phones are pretty naff.

    FWIW my Snom D120s are much clearer than any analogue phone I've ever used.
    --
    Brian Gregory (in England).
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Brian Gregory@void-invalid-dead-dontuse@email.invalid to uk.telecom on Fri Oct 16 19:30:07 2026
    From Newsgroup: uk.telecom

    On 16/10/2026 17:37, Scott wrote:
    On Fri, 16 Oct 2026 17:16:52 +0100, Brian Gregory <void-invalid-dead-dontuse@email.invalid> wrote:

    On 16/10/2026 16:40, Scott wrote:
    I don't know if this helps or hinders but I already have a cordless
    VOIP phone (FRITZ!Fon) that links direct to the router (so I assume
    the basic set-up is in place). Now I am thinking about a corded VOIP
    (SIP) phone for my desk as the audio quality is not too good on the
    traditional phone I am using.

    You will need Fritzbox documentation to find out about configuring a
    VoIP phone to connect to and use the Fritzbox as a kind of switchboard
    rather than to connect directly to Zen.

    Why can't it be connected in the same way as the FRITZ!Fon? Is SIP the
    same as VOIP?

    Oh! Is the FRITZ!Fon not DECT? Most are.
    If not and it's VoIP then do you know how its VoIP is configured?
    --
    Brian Gregory (in England).
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Marco Moock@mm@dorfdsl.de to uk.telecom on Fri Oct 16 20:34:14 2026
    From Newsgroup: uk.telecom

    Am 16.10.26 um 13:03 schrieb The Natural Philosopher:
    On 16/10/2026 10:49, Marco Moock wrote:
    Am 16.10.26 um 11:05 schrieb Richmond:
    Does the sound quality of VOIP depend on the ISPs network and the
    compression protocol it accepts? and also the recipients network.

    Of course. There are different codecs and your ISP might convert them
    if needed.

    The ISP is not involved in inspeccting packets passing through it or changing their protocols.

    As many people use the VoIP service from their ISP, I used that term. In
    case they use something else, that service will do the VoIP stuff. How
    is such a service provider properly called?

    The codecs in use are a function of the endpoints, which are other VOIP phones

    VOIP has NOTHING to do with the ISP at all. Unless they are running
    their own SIP server and/or POTS gateway

    They do that and most users use such a service. Direct VOIP calling is possible, but no normal users uses that. There was an idea to use DNS to
    get the remote's IP, but the telephone companies didn't like that.

    Or shuffling packet queus based on whether there is a viOPp packet in them


    The recipient's device and used codec is also relevant, as the lowest
    standard will define the speech quality.


    That is ALL that is relevant, that and the bandwidth, packet loss-a and latency between the devices

    In case there is a mismatch, a conversion needs to be done. Depending on
    how the telephone companies route the phone traffic, they might need to
    change to a lower codec.
    --
    Gru|f
    Marco

    Spam bitte an abfalleimer2001@stinkedores.dorfdsl.de
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Marco Moock@mm@dorfdsl.de to uk.telecom on Fri Oct 16 20:35:50 2026
    From Newsgroup: uk.telecom

    Am 16.10.26 um 17:31 schrieb Andy Burns:
    Brian Gregory wrote:

    The Natural Philosopher wrote:
    VOIP has NOTHING to do with the ISP at all. Unless they are running
    their own SIP server and/or POTS gateway

    Which obviously they are, since his analogue phone was plugged into
    his router.
    More likely the router separates off the VoIP traffic, and sends it to servers operated by (guessing) BT or Magrathea

    This is a description about Germany with VDSL:
    Some ISPs want it in a separate VLAN. Others run it over the same VLAN
    as the normal internet traffic.
    --
    Gru|f
    Marco

    Spam bitte an abfalleimer2001@stinkedores.dorfdsl.de
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Marco Moock@mm@dorfdsl.de to uk.telecom on Fri Oct 16 20:37:11 2026
    From Newsgroup: uk.telecom

    Am 16.10.26 um 16:44 schrieb David Wade:

    No it needs to be configured both in the Fritz!Box and in the phone.
    Just check if you go to Telephony-> Devices in the Fritz you can add a device and add a network telephone.

    You can also let the VoIP phone register at the SIP server.
    Although, the router's firewall needs to be configured to let the
    SIP/RTP packets through. Not very model supports such rulesets.
    --
    Gru|f
    Marco

    Spam bitte an abfalleimer2001@stinkedores.dorfdsl.de
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From The Natural Philosopher@tnp@invalid.invalid to uk.telecom on Fri Oct 16 21:06:09 2026
    From Newsgroup: uk.telecom

    On 16/10/2026 12:57, Scott wrote:
    On Fri, 16 Oct 2026 11:58:33 +0100, The Natural Philosopher <tnp@invalid.invalid> wrote:

    On 16/10/2026 10:05, Richmond wrote:
    Brian Gregory <void-invalid-dead-dontuse@email.invalid> writes:


    Sometimes using an analogue phone with any ATA (Analog Telephone
    Adapter) that allows an ordinary analogue phone to connect to VoIP
    results in poor sound and/or some echo which can mostly be avoided by
    using a VoIP phone.


    Does the sound quality of VOIP depend on the ISPs network and the
    compression protocol it accepts? and also the recipients network.

    IME with first Cisco and then Draytek routers with VOIP ports, the only
    degradation below 'better than POTS by a large margin' was packet loss
    causing breakup and distortion when my (now ex) wife was watching a
    video

    A situation you obviously dealt with decisively :-)

    Yaeh. Now I have no wife and fibre to the premises.
    Good upgrade
    --
    "Strange as it seems, no amount of learning can cure stupidity, and
    higher education positively fortifies it."

    - Stephen Vizinczey


    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From The Natural Philosopher@tnp@invalid.invalid to uk.telecom on Fri Oct 16 21:09:30 2026
    From Newsgroup: uk.telecom

    On 16/10/2026 13:03, Scott wrote:
    As it happens, it is a FRITZ!Box and Zen is my ISP. Does this mean I
    can plug it into a LAN port (not FON) and will it work out of the box?
    Does SIP phone require a power supply?

    The Fritzbox should have enough power to drive a basic analogue phone

    If it is compatible with the SIP service it just needs a connection to
    your LAN, and some power.
    --
    "Strange as it seems, no amount of learning can cure stupidity, and
    higher education positively fortifies it."

    - Stephen Vizinczey


    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From The Natural Philosopher@tnp@invalid.invalid to uk.telecom on Fri Oct 16 21:05:19 2026
    From Newsgroup: uk.telecom

    On 16/10/2026 12:30, Richmond wrote:
    Andy Burns <usenet@andyburns.uk> writes:

    The Natural Philosopher wrote:

    VOIP has NOTHING to do with the ISP at all. Unless they are running
    their own SIP server and/or POTS gateway

    I think you're right to assume that most ISPs outsource the VoIP, but
    not all do (e.g. AAISP)

    I am with AAISP. But I see Voipfone is also an ISP. And anyone who runs
    a SIP registrar/proxy to handle registration and call routing is
    technically an ISP.
    Not really. ISP is technically someone who provides access to the
    Internet, someone who runs a server on it is hardly an ISP
    --
    "Strange as it seems, no amount of learning can cure stupidity, and
    higher education positively fortifies it."

    - Stephen Vizinczey


    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From The Natural Philosopher@tnp@invalid.invalid to uk.telecom on Fri Oct 16 21:11:35 2026
    From Newsgroup: uk.telecom

    On 16/10/2026 16:31, Andy Burns wrote:
    Brian Gregory wrote:

    The Natural Philosopher wrote:
    VOIP has NOTHING to do with the ISP at all. Unless they are running
    their own SIP server and/or POTS gateway

    Which obviously they are, since his analogue phone was plugged into
    his router.
    More likely the router separates off the VoIP traffic, and sends it to servers operated by (guessing) BT or Magrathea

    Well exactly. MY sip capable router talks to a yonks old SIPGATE free
    service which still works
    --
    "Nature does not give up the winter because people dislike the cold."

    rCo Confucius

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From The Natural Philosopher@tnp@invalid.invalid to uk.telecom on Fri Oct 16 21:19:25 2026
    From Newsgroup: uk.telecom

    On 16/10/2026 17:41, Andy Burns wrote:
    Scott wrote:

    Why can't it be connected in the same way as the FRITZ!Fon? Is SIP the
    same as VOIP?

    Basically yes ... SIP is the signalling protocol and RTP is used for the actual audio/video.
    AIUI the sip server simply registers your phone number IP address and
    port number, so when someone wants to connect to your phone they know
    which port to access on which IP address

    It may act as a proxy too,

    But ideally it takes no part in sending voice packets
    Its more like a DNS server than a router.

    So e.g if you want to phone someone it says 'contact 176.4.35.1 on port
    9900' and so you do, and the other end says 'hi im a voip line' and you
    talk direct

    If its being mapped to a land line it needs a special gateway, but since everyone is going VOIP I expect less use of that. More likely a gateway
    to mobile.

    That is what costs money. Voip to Voip should be free
    --
    rCLI know that most men, including those at ease with problems of the greatest complexity, can seldom accept even the simplest and most
    obvious truth if it be such as would oblige them to admit the falsity of conclusions which they have delighted in explaining to colleagues, which
    they have proudly taught to others, and which they have woven, thread by thread, into the fabric of their lives.rCY

    rCo Leo Tolstoy

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From The Natural Philosopher@tnp@invalid.invalid to uk.telecom on Fri Oct 16 21:36:46 2026
    From Newsgroup: uk.telecom

    On 16/10/2026 18:55, David Wade wrote:
    On 16/10/2026 18:41, Scott wrote:
    On Fri, 16 Oct 2026 17:59:35 +0100, David Wade <g4ugm@dave.invalid>
    wrote:

    On 16/10/2026 16:40, Scott wrote:
    On Fri, 16 Oct 2026 16:04:02 +0100, Brian Gregory
    <void-invalid-dead-dontuse@email.invalid> wrote:

    On 16/10/2026 13:03, Scott wrote:
    As it happens, it is a FRITZ!Box and Zen is my ISP. Does this mean I >>>>>> can plug it into a LAN port (not FON) and will it work out of the >>>>>> box?
    Does SIP phone require a power supply?

    I'm with Zen.

    But I'm not using the Fritzbox. I couldn't cope with the weird names >>>>> they call things that are presumably simplistic translations of their >>>>> German names. But now I suspect my setup is also more complicated than >>>>> the Fritzbox is capable of.

    Zen's, rather limited, information on setting up your own VoIP
    device is
    here:
    https://www.zen.co.uk/help-support/general-sip-settings/

    I set mine up using info in a blog I found before I knew about that >>>>> page
    and I used UDP ports 10000-20000 for RTP while Zen says "Media Call
    Audio Addresses Ports - 20000 to 30000 UDP" so I guess you can
    actually
    use whatever you want in that case. Also it did seem to be easy enough >>>>> to get it to work without port forwarding those ports, but I chose to >>>>> port forward, but only UDP from Zen's VoIP servers (62.3.88.0/27).

    Also note that the Fritzbox provides some of the service like the
    answering machine which you won't get on Zen with most VoIP phones.

    I don't know if this helps or hinders but I already have a cordless
    VOIP phone (FRITZ!Fon) that links direct to the router (so I assume
    the basic set-up is in place). Now I am thinking about a corded VOIP
    (SIP) phone for my desk as the audio quality is not too good on the
    traditional phone I am using.

    Personally I would try a DECT phone linked to the Fritz!box DECT Base. I >>> have a Panasonic linked direct to my FritzBox and I think the call
    quality is better than the IP Phone I tried. You can do some tweaking of >>> the audio in the Fritz...

    Dave
    p.s. this model

    https://www.ebay.co.uk/itm/237126660958

    Why would a DECT phone linked to the FRITZ!Box be better that a corded
    phone linked to the FRITZ!Box?

    Because many corded phones are pretty naff.

    Golly., I have loads of old pre loved office and hotel desk phones with
    lovely features like redial last number and speaker mode. essential for
    those 'you are number 32 in the queue, please hold' occasions. Its got memories as well but ICBA with that.

    Great quality at under -u15 pre loved - Doro AUB300i. Used to retail
    around -u70. No idea where this one came from but its been my phone for
    nearly 30 years now

    I've got others that are similar to the old BT viscount range

    And even a new alcatel is really good value

    https://www.pmctelecom.co.uk/alcatel-t26-basic-telephone-black

    Whether you want a really good quality deskphone adapted to VOIP or some
    more expensive gadget infested cordless VOIP phone is up to you

    Personally, my telephony needs are tending towards zero

    texts, email and Whatsapp are far more in use

    Dave
    --
    "A point of view can be a dangerous luxury when substituted for insight
    and understanding".

    Marshall McLuhan


    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From The Natural Philosopher@tnp@invalid.invalid to uk.telecom on Fri Oct 16 21:37:26 2026
    From Newsgroup: uk.telecom

    On 16/10/2026 19:30, Brian Gregory wrote:
    On 16/10/2026 17:37, Scott wrote:
    On Fri, 16 Oct 2026 17:16:52 +0100, Brian Gregory
    <void-invalid-dead-dontuse@email.invalid> wrote:

    On 16/10/2026 16:40, Scott wrote:
    I don't know if this helps or hinders but I already have a cordless
    VOIP phone (FRITZ!Fon) that links direct to the router (so I assume
    the basic set-up is in place). Now I am thinking about a corded VOIP
    (SIP) phone for my desk as the audio quality is not too good on the
    traditional phone I am using.

    You will need Fritzbox documentation to find out about configuring a
    VoIP phone to connect to and use the Fritzbox as a kind of switchboard
    rather than to connect directly to Zen.

    Why can't it be connected in the same way as the FRITZ!Fon? Is SIP the
    same as VOIP?

    Oh! Is the FRITZ!Fon not DECT? Most are.
    If not and it's VoIP then do you know how its VoIP is configured?

    I expect most have a web interface
    --
    "Fanaticism consists in redoubling your effort when you have
    forgotten your aim."

    George Santayana

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From The Natural Philosopher@tnp@invalid.invalid to uk.telecom on Fri Oct 16 21:39:49 2026
    From Newsgroup: uk.telecom

    On 16/10/2026 19:34, Marco Moock wrote:
    Am 16.10.26 um 13:03 schrieb The Natural Philosopher:
    On 16/10/2026 10:49, Marco Moock wrote:
    Am 16.10.26 um 11:05 schrieb Richmond:
    Does the sound quality of VOIP depend on the ISPs network and the
    compression protocol it accepts? and also the recipients network.

    Of course. There are different codecs and your ISP might convert them
    if needed.

    The ISP is not involved in inspeccting packets passing through it or
    changing their protocols.

    As many people use the VoIP service from their ISP, I used that term. In case they use something else, that service will do the VoIP stuff. How
    is such a service provider properly called?

    The codecs in use are a function of the endpoints, which are other
    VOIP phones

    VOIP has NOTHING to do with the ISP at all. Unless they are running
    their own SIP server and/or POTS gateway

    They do that and most users use such a service. Direct VOIP calling is possible, but no normal users uses that. There was an idea to use DNS to
    get the remote's IP, but the telephone companies didn't like that.

    Or shuffling packet queus based on whether there is a viOPp packet in
    them


    The recipient's device and used codec is also relevant, as the lowest
    standard will define the speech quality.


    That is ALL that is relevant, that and the bandwidth, packet loss-a and
    latency between the devices

    In case there is a mismatch, a conversion needs to be done. Depending on
    how the telephone companies route the phone traffic, they might need to change to a lower codec.

    The end points negotiate that. And most voip to voip does not involve
    the SIP server
    VOIPto other shit involves and expensive VOIP gateway.

    SIP server is DNS for telephone numbers rather than web sites
    --
    "Fanaticism consists in redoubling your effort when you have
    forgotten your aim."

    George Santayana

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From The Natural Philosopher@tnp@invalid.invalid to uk.telecom on Fri Oct 16 21:49:52 2026
    From Newsgroup: uk.telecom

    On 16/10/2026 19:37, Marco Moock wrote:
    Am 16.10.26 um 16:44 schrieb David Wade:

    No it needs to be configured both in the Fritz!Box and in the phone.
    Just check if you go to Telephony-> Devices in the Fritz you can add a
    device and add a network telephone.

    You can also let the VoIP phone register at the SIP server.
    Although, the router's firewall needs to be configured to let the
    SIP/RTP packets through. Not very model supports such rulesets.

    Yes. essentially the fritzbox or the pure voiphone need to connect to a
    SIP server which as a record of their 'phone number' and registers an IP
    and port address ion it.

    The router has to allow incoming traffic to reach that port. Sometimes
    NAT will do it but mostly the router needs to map the frirzbox/voip
    phone ip address and port to a public ip address and port.

    My router contains the equoivalent of two fritz boxes as well as its
    normal fiunctions

    In use, to dial out, you contact the server with the number you want to contact, and that either tells you how to contact it directly via IP address/port, ifs its VOIP or directs you to a gateway to POTS or mobile services or proxies the connection to a remote number itself

    To receive a call you simply accept packets for your designated
    interface, which is in the public domain once you register with the sip
    server

    For the rash of BT transfers I would imagine you get a box or a router
    that is all completely preconfigured. BT regards most of its customer
    base as complete morons, and frankly only real morons are still with them...
    --
    The urge to save humanity is almost always a false front for the urge to
    rule.
    rCo H. L. Mencken, American journalist, 1880-1956

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Brian Gregory@void-invalid-dead-dontuse@email.invalid to uk.telecom on Fri Oct 16 22:55:09 2026
    From Newsgroup: uk.telecom

    On 16/10/2026 21:37, The Natural Philosopher wrote:
    On 16/10/2026 19:30, Brian Gregory wrote:
    On 16/10/2026 17:37, Scott wrote:
    On Fri, 16 Oct 2026 17:16:52 +0100, Brian Gregory
    <void-invalid-dead-dontuse@email.invalid> wrote:

    On 16/10/2026 16:40, Scott wrote:
    I don't know if this helps or hinders but I already have a cordless
    VOIP phone (FRITZ!Fon) that links direct to the router (so I assume
    the basic set-up is in place). Now I am thinking about a corded VOIP >>>>> (SIP) phone for my desk as the audio quality is not too good on the
    traditional phone I am using.

    You will need Fritzbox documentation to find out about configuring a
    VoIP phone to connect to and use the Fritzbox as a kind of switchboard >>>> rather than to connect directly to Zen.

    Why can't it be connected in the same way as the FRITZ!Fon? Is SIP the
    same as VOIP?

    Oh! Is the FRITZ!Fon not DECT? Most are.
    If not and it's VoIP then do you know how its VoIP is configured?

    I expect most have a web interface


    Google thinks all FRITZ!Fon are DECT, not VoIP.
    --
    Brian Gregory (in England).
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From J. P. Gilliver@G6JPG@255soft.uk to uk.telecom on Sat Oct 17 02:23:31 2026
    From Newsgroup: uk.telecom

    On 2026/10/16 10:49:50, Marco Moock wrote:
    Am 16.10.26 um 11:05 schrieb Richmond:
    Does the sound quality of VOIP depend on the ISPs network and the
    compression protocol it accepts? and also the recipients network.

    Of course. There are different codecs and your ISP might convert them if needed.

    The recipient's device and used codec is also relevant, as the lowest standard will define the speech quality.

    In some discussion on this matter a while back (external ATAs were the
    main consideration at that point), some people in the discussion said
    that some ATAs could handle a variety of compression/encoding protocols,
    and some said you could choose the one you wanted to use. (That
    discussion started out by comaparing the quality of VoIP to normal POTS,
    with some [people with hearing impairments] saying they couldn't get on
    with e. g. whatever mobile 'phones use, only normal 'phones; others
    pointed out that normal 'phones use an encoding/compression standard
    anyway, and even named it [I think it was a 5 or 6 character string of
    letters and numbers].)
    --
    J. P. Gilliver. UMRA: 1960/<1985 MB++G()ALIS-Ch++(p)Ar++T+H+Sh0!:`)DNAf
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From J. P. Gilliver@G6JPG@255soft.uk to uk.telecom on Sat Oct 17 02:34:38 2026
    From Newsgroup: uk.telecom

    On 2026/10/16 21:6:9, The Natural Philosopher wrote:
    []

    Yaeh. Now I have no wife and fibre to the premises.
    Good upgrade

    Wifeless wifi!
    --
    J. P. Gilliver. UMRA: 1960/<1985 MB++G()ALIS-Ch++(p)Ar++T+H+Sh0!:`)DNAf
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From J. P. Gilliver@G6JPG@255soft.uk to uk.telecom on Sat Oct 17 02:52:32 2026
    From Newsgroup: uk.telecom

    On 2026/10/16 9:26:4, David Wade wrote:
    On 15/10/2026 23:03, Brian Gregory wrote:
    On 15/10/2026 21:19, Scott wrote:
    I have a router beside my desk with a standard phone plugged into it.
    Do corded VOIP phones exist and would they offer any benefit?


    If you mean a device plugs into the local LAN and talks VOIP yes these exist. However they can't be used with EE ot BT routers as these are
    locked down.

    Thanks for the warning. Probably not a problem to me initially, as I'll
    almost certainly be using such (and will be with such routers), since I
    will otherwise have redundant 'phones I can't sell and have no desire to
    scrap.

    (Interesting side-thought: both EE and BT offer "adapters" for use "if
    your router is in an awkward place" - there are devices that just plug
    into a mains socket, and you plug your [analogue] 'phone into them, and
    they link to the router. Do they contain ATA hardware, or is that all in
    the router and their connection to the router is by some yet other
    protocol, possibly even analogue?)

    Also: when I first looked into VoIP, one of the options - cost-free, as
    opposed to having to buy either an ATA or a VoIP-enabled 'phone - was
    the entirely-software method, where you used your (e. g.) laptop's
    speaker and microphone, somewhat like a Skype/Zoom/whatever call (sound
    only, of course), I suppose. I've seen no mention of this lately - is it considerably inferior and just a get-started system while you're waiting
    for your ATA to be delivered, or ...? Also, can it be used with the
    BT/EE routers or do they block that too?


    Yes they do.
    I have two Snom D120 (wired) phones. (At present I only use one.
    Connecting more than one to a VoIP service designed for a single ATA is
    complicated)


    You might want to look at a used Fritz!Box router with VOIP as they can
    act as a SIP server and mini PABX. You can of course also run Asterisk
    on a PI or similar.

    So it's the router, not the ISP contract/whatever, that is the block/lock?

    []
    It depends on the router and VOIP service. So if its a BT or EE router
    you are locked into BT devices and can't add a "corded" SIP phone.

    Or, presumably, an external ATA (not that I can see why you'd want to as there's in effect one in the router), as that would in effect be a VoIP
    'phone.


    If its a Fritz!box from ZEN that can act as a SIP server and mini PABX.
    So by having multiple SIP phones connected by Ethernet you can have your
    own internal phone system with extension dialing. As its also a DECT
    base station you can do the same with DECT

    Dave

    They certainly - whether deliberately or not, and I think it's probably not-deliberately-but-they-don't-want-too-expend-any-effort-explaining -
    seem to be concealing what does what. Much like - especially in the
    early days - mobile companies confused the public about the difference
    between the hardware and the service.
    --
    J. P. Gilliver. UMRA: 1960/<1985 MB++G()ALIS-Ch++(p)Ar++T+H+Sh0!:`)DNAf
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From J. P. Gilliver@G6JPG@255soft.uk to uk.telecom on Sat Oct 17 02:57:31 2026
    From Newsgroup: uk.telecom

    On 2026/10/16 21:19:25, The Natural Philosopher wrote:
    []
    If its being mapped to a land line it needs a special gateway, but since everyone is going VOIP I expect less use of that. More likely a gateway
    to mobile.

    That is what costs money. Voip to Voip should be free


    Interesting point - but, initially at least, they've managed to arrange
    that it's _not_ free (though cheap), other than anytime contracts (which
    cost more so aren't free either).

    _Hopefully_, it'll be like broadband eventually: I remember when many,
    if not most, broadband contracts had usage caps; I doubt there are many,
    if any, such remaining now (for fibre or copper connections I mean,
    rather than over the mobile network where I think they mostly still are).
    --
    J. P. Gilliver. UMRA: 1960/<1985 MB++G()ALIS-Ch++(p)Ar++T+H+Sh0!:`)DNAf

    You can be tough without being rude - Nick Clegg, 2014 July
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From The Natural Philosopher@tnp@invalid.invalid to uk.telecom on Sat Oct 17 08:47:20 2026
    From Newsgroup: uk.telecom

    On 17/10/2026 02:23, J. P. Gilliver wrote:
    In some discussion on this matter a while back (external ATAs were the
    main consideration at that point), some people in the discussion said
    that some ATAs could handle a variety of compression/encoding protocols,
    and some said you could choose the one you wanted to use.

    I THINK that is correct. My router has tunable options for VOIP, AIUI
    the endpoint VOIP units (whatever they are ) negotiate a common
    standard, or at least acceptable ones in both direction. Mine is
    currently set to 'prefer' an 8kbps codec. This gives excellent results
    but faster options are avialable


    (That
    discussion started out by comaparing the quality of VoIP to normal POTS,
    with some [people with hearing impairments] saying they couldn't get on
    with e. g. whatever mobile 'phones use, only normal 'phones; others
    pointed out that normal 'phones use an encoding/compression standard
    anyway, and even named it [I think it was a 5 or 6 character string of letters and numbers].)

    'Normal' phones use a 64kbps fixed TDM . Crude by today's standards but
    very advanced when it first came out. I am fairly sure that conversion
    to and from analogue happens at the exchange.

    That is why modems could only ever reach 56Kbps or thereabouts and ISDN
    lines were 64kbps digital

    UK backbone is/was built of links that are multiples of this speed,

    Then I think it moved to frame relay, but the basic encoding didn't change
    VOIP phones use 'intelligent' codecs that can get te same or bvetter
    quality into e.g an 8kbps channel

    Mobile data rates are much much lower. Hundreds of calls need to be
    squeezed into a very limited RF spectrum. 8kbps is luxury. 1kbps is
    normal and in congested areas even less. To the point where it becomes unintelligible.

    Mobile is not VOIP. There is - or was - no IP involved. Different
    standards to meet different limitations. Mobiles are massively bandwidth limited, but even an ADSL links is way way faster than a mobile link
    *used* to be. I cant answer for 4G/5G

    So mobile is like VOIP is a completely false statement, Qualitry IS
    NOTHING like VOIP. Its like comparing Radio Caroline on the MW with a
    full power VHF radio signal
    --
    rCLPuritanism: The haunting fear that someone, somewhere, may be happy.rCY

    H.L. Mencken, A Mencken Chrestomathy

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From The Natural Philosopher@tnp@invalid.invalid to uk.telecom on Sat Oct 17 08:49:53 2026
    From Newsgroup: uk.telecom

    On 17/10/2026 02:57, J. P. Gilliver wrote:
    On 2026/10/16 21:19:25, The Natural Philosopher wrote:
    []
    If its being mapped to a land line it needs a special gateway, but since
    everyone is going VOIP I expect less use of that. More likely a gateway
    to mobile.

    That is what costs money. Voip to Voip should be free


    Interesting point - but, initially at least, they've managed to arrange
    that it's _not_ free (though cheap), other than anytime contracts (which
    cost more so aren't free either).

    _Hopefully_, it'll be like broadband eventually: I remember when many,
    if not most, broadband contracts had usage caps; I doubt there are many,
    if any, such remaining now (for fibre or copper connections I mean,
    rather than over the mobile network where I think they mostly still are).

    TBH I am not sure how long VOIP phones will last anyway. WE have
    [essentially] free whatsapp or skype messaging, and mobile phones with
    data connections.

    VOIP is replacing a technology that is already passing out of use.
    --
    rCLSome people like to travel by train because it combines the slowness of
    a car with the cramped public exposure of rC?an airplane.rCY

    Dennis Miller


    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Chris Green@cl@isbd.net to uk.telecom on Sat Oct 17 09:08:09 2026
    From Newsgroup: uk.telecom

    Brian Gregory <void-invalid-dead-dontuse@email.invalid> wrote:
    On 16/10/2026 21:37, The Natural Philosopher wrote:
    On 16/10/2026 19:30, Brian Gregory wrote:
    On 16/10/2026 17:37, Scott wrote:
    On Fri, 16 Oct 2026 17:16:52 +0100, Brian Gregory
    <void-invalid-dead-dontuse@email.invalid> wrote:

    On 16/10/2026 16:40, Scott wrote:
    I don't know if this helps or hinders but I already have a cordless >>>>> VOIP phone (FRITZ!Fon) that links direct to the router (so I assume >>>>> the basic set-up is in place). Now I am thinking about a corded VOIP >>>>> (SIP) phone for my desk as the audio quality is not too good on the >>>>> traditional phone I am using.

    You will need Fritzbox documentation to find out about configuring a >>>> VoIP phone to connect to and use the Fritzbox as a kind of switchboard >>>> rather than to connect directly to Zen.

    Why can't it be connected in the same way as the FRITZ!Fon? Is SIP the >>> same as VOIP?

    Oh! Is the FRITZ!Fon not DECT? Most are.
    If not and it's VoIP then do you know how its VoIP is configured?

    I expect most have a web interface


    Google thinks all FRITZ!Fon are DECT, not VoIP.

    But DECT and VOIP are not mutually exclusive, it's perfectly possible
    to have a VOIP system that uses DECT handsets. It's also possible to
    have both a DECT/VOIP system and a separate VOIP phone using the same
    router (I've done it!). The router doesn't really know or care if a
    device that's connected to it is VOIP or any other protocol.
    --
    Chris Green
    -+
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From David Wade@g4ugm@dave.invalid to uk.telecom on Sat Oct 17 09:29:21 2026
    From Newsgroup: uk.telecom

    On 17/10/2026 02:52, J. P. Gilliver wrote:
    On 2026/10/16 9:26:4, David Wade wrote:
    On 15/10/2026 23:03, Brian Gregory wrote:
    On 15/10/2026 21:19, Scott wrote:
    I have a router beside my desk with a standard phone plugged into it.
    Do corded VOIP phones exist and would they offer any benefit?


    If you mean a device plugs into the local LAN and talks VOIP yes these
    exist. However they can't be used with EE ot BT routers as these are
    locked down.

    Thanks for the warning. Probably not a problem to me initially, as I'll almost certainly be using such (and will be with such routers), since I
    will otherwise have redundant 'phones I can't sell and have no desire to scrap.

    But as you can't add ATAs either you need to hard wire these as POTS
    phones. You can get a cable that lets you link your existing house
    wiring into the pots port on the router.


    (Interesting side-thought: both EE and BT offer "adapters" for use "if
    your router is in an awkward place" - there are devices that just plug
    into a mains socket, and you plug your [analogue] 'phone into them, and
    they link to the router. Do they contain ATA hardware, or is that all in
    the router and their connection to the router is by some yet other
    protocol, possibly even analogue?)

    they appear to be DECT..


    Also: when I first looked into VoIP, one of the options - cost-free, as opposed to having to buy either an ATA or a VoIP-enabled 'phone - was
    the entirely-software method, where you used your (e. g.) laptop's
    speaker and microphone, somewhat like a Skype/Zoom/whatever call (sound
    only, of course), I suppose. I've seen no mention of this lately - is it considerably inferior and just a get-started system while you're waiting
    for your ATA to be delivered, or ...? Also, can it be used with the
    BT/EE routers or do they block that too?


    These generally use SIP so can't be used with BT/EE Digital Voice. Just
    be carefull when googling as BT does have "Digital Voice for Business"
    which is unlocked and does have apps available

    https://business.bt.com/calling-messaging-tools/voip/digital-voice-for-business/



    Yes they do.
    I have two Snom D120 (wired) phones. (At present I only use one.
    Connecting more than one to a VoIP service designed for a single ATA is
    complicated)


    You might want to look at a used Fritz!Box router with VOIP as they can
    act as a SIP server and mini PABX. You can of course also run Asterisk
    on a PI or similar.

    So it's the router, not the ISP contract/whatever, that is the block/lock?

    []
    It depends on the router and VOIP service. So if its a BT or EE router
    you are locked into BT devices and can't add a "corded" SIP phone.

    Or, presumably, an external ATA (not that I can see why you'd want to as there's in effect one in the router), as that would in effect be a VoIP 'phone.


    correct. If you are using the ZEN router with POTS phones extra ATAs
    each have there own "extension number" so you can make internal calls.

    you can add DECT phones ...


    If its a Fritz!box from ZEN that can act as a SIP server and mini PABX.
    So by having multiple SIP phones connected by Ethernet you can have your
    own internal phone system with extension dialing. As its also a DECT
    base station you can do the same with DECT

    Dave

    They certainly - whether deliberately or not, and I think it's probably not-deliberately-but-they-don't-want-too-expend-any-effort-explaining -
    seem to be concealing what does what. Much like - especially in the
    early days - mobile companies confused the public about the difference between the hardware and the service.

    Both BT and EE (I know same company) want everything to be "plug and
    play" and to achieve this they lock things down.
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From J. P. Gilliver@G6JPG@255soft.uk to uk.telecom on Sat Oct 17 09:32:17 2026
    From Newsgroup: uk.telecom

    On 2026/10/17 8:49:53, The Natural Philosopher wrote:
    On 17/10/2026 02:57, J. P. Gilliver wrote:
    On 2026/10/16 21:19:25, The Natural Philosopher wrote:
    []
    If its being mapped to a land line it needs a special gateway, but since >>> everyone is going VOIP I expect less use of that. More likely a gateway
    to mobile.

    That is what costs money. Voip to Voip should be free


    Interesting point - but, initially at least, they've managed to arrange
    that it's _not_ free (though cheap), other than anytime contracts (which
    cost more so aren't free either).

    _Hopefully_, it'll be like broadband eventually: I remember when many,
    if not most, broadband contracts had usage caps; I doubt there are many,
    if any, such remaining now (for fibre or copper connections I mean,
    rather than over the mobile network where I think they mostly still are).

    TBH I am not sure how long VOIP phones will last anyway. WE have [essentially] free whatsapp or skype messaging, and mobile phones with
    data connections.

    VOIP is replacing a technology that is already passing out of use.

    For private comm.s, perhaps (though I intend to continue using it). Most
    large businesses still use it, and government; yes, your local builder, plumber, etc., might use only a mobile, but insurance companies, pension companies, banks, government agencies ... will continue to use
    landline-type numbers.

    When listing builders etc., it reminded me of a thought I had recently:
    most taxi companies I see still have just their local number on the
    things on the roof of their cars, and similar. (Often an easy-to-use
    one, such as ending in three identical digits.) I was thinking, they'll
    have to start putting the area codes in; OK, local people will (probably
    - maybe decreasingly so?) know the local code, but people from outside
    the area - who might well be potential taxi customers - won't.
    (I suppose they'll all switch to mobiles anyway, but it may not be so
    easy to get memorable those.)
    --
    J. P. Gilliver. UMRA: 1960/<1985 MB++G()ALIS-Ch++(p)Ar++T+H+Sh0!:`)DNAf

    A lie doesn't become truth just because people believe it
    - https://www.youtube.com/watch?v=zYoH8796SFE
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Scott@newsgroups@gefion.myzen.co.uk to uk.telecom on Sat Oct 17 09:44:02 2026
    From Newsgroup: uk.telecom

    On Sat, 17 Oct 2026 09:08:09 +0100, Chris Green <cl@isbd.net> wrote:

    Brian Gregory <void-invalid-dead-dontuse@email.invalid> wrote:
    On 16/10/2026 21:37, The Natural Philosopher wrote:
    On 16/10/2026 19:30, Brian Gregory wrote:
    On 16/10/2026 17:37, Scott wrote:
    On Fri, 16 Oct 2026 17:16:52 +0100, Brian Gregory
    <void-invalid-dead-dontuse@email.invalid> wrote:

    On 16/10/2026 16:40, Scott wrote:
    I don't know if this helps or hinders but I already have a cordless
    VOIP phone (FRITZ!Fon) that links direct to the router (so I assume
    the basic set-up is in place). Now I am thinking about a corded VOIP >> >>>>> (SIP) phone for my desk as the audio quality is not too good on the
    traditional phone I am using.

    You will need Fritzbox documentation to find out about configuring a
    VoIP phone to connect to and use the Fritzbox as a kind of switchboard >> >>>> rather than to connect directly to Zen.

    Why can't it be connected in the same way as the FRITZ!Fon? Is SIP the >> >>> same as VOIP?

    Oh! Is the FRITZ!Fon not DECT? Most are.
    If not and it's VoIP then do you know how its VoIP is configured?

    I expect most have a web interface


    Google thinks all FRITZ!Fon are DECT, not VoIP.

    But DECT and VOIP are not mutually exclusive, it's perfectly possible
    to have a VOIP system that uses DECT handsets. It's also possible to
    have both a DECT/VOIP system and a separate VOIP phone using the same
    router (I've done it!). The router doesn't really know or care if a
    device that's connected to it is VOIP or any other protocol.

    I understood this (cordless) VOIP handset runs off the WiFi with
    nothing connected to the 'FON' port on the router - or are you saying
    the router may have DECT as well as WiFi built in?
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Scott@newsgroups@gefion.myzen.co.uk to uk.telecom on Sat Oct 17 09:49:20 2026
    From Newsgroup: uk.telecom

    On Fri, 16 Oct 2026 21:09:30 +0100, The Natural Philosopher <tnp@invalid.invalid> wrote:

    On 16/10/2026 13:03, Scott wrote:
    As it happens, it is a FRITZ!Box and Zen is my ISP. Does this mean I
    can plug it into a LAN port (not FON) and will it work out of the box?
    Does SIP phone require a power supply?

    The Fritzbox should have enough power to drive a basic analogue phone

    Yes it can but the audio quality is not very good (not as good at the
    cordless) and there is a loud buzzing noise.

    If it is compatible with the SIP service it just needs a connection to
    your LAN, and some power.

    I can do that with the cordless but I wondered about a corded phone
    for my desk (with the option of headphones) given that the router is
    only 1 metre away.
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Andy Burns@usenet@andyburns.uk to uk.telecom on Sat Oct 17 10:06:40 2026
    From Newsgroup: uk.telecom

    The Natural Philosopher wrote:

    Mobile is not VOIP. There is - or was - no IP involved.

    The only mobile that *isn't* VoIP is 2G.

    3G is gone.

    4G and 5G are pure IP networks, VoLTE is SIP/RTP over IP, VoNR is the equivalent for 5G.

    Granted, phones can for the short term choose to drop to 2G to do voice.

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Chris Green@cl@isbd.net to uk.telecom on Sat Oct 17 10:06:25 2026
    From Newsgroup: uk.telecom

    Scott <newsgroups@gefion.myzen.co.uk> wrote:
    On Sat, 17 Oct 2026 09:08:09 +0100, Chris Green <cl@isbd.net> wrote:

    Brian Gregory <void-invalid-dead-dontuse@email.invalid> wrote:
    On 16/10/2026 21:37, The Natural Philosopher wrote:
    On 16/10/2026 19:30, Brian Gregory wrote:
    On 16/10/2026 17:37, Scott wrote:
    On Fri, 16 Oct 2026 17:16:52 +0100, Brian Gregory
    <void-invalid-dead-dontuse@email.invalid> wrote:

    On 16/10/2026 16:40, Scott wrote:
    I don't know if this helps or hinders but I already have a cordless >> >>>>> VOIP phone (FRITZ!Fon) that links direct to the router (so I assume >> >>>>> the basic set-up is in place). Now I am thinking about a corded VOIP >> >>>>> (SIP) phone for my desk as the audio quality is not too good on the >> >>>>> traditional phone I am using.

    You will need Fritzbox documentation to find out about configuring a >> >>>> VoIP phone to connect to and use the Fritzbox as a kind of switchboard
    rather than to connect directly to Zen.

    Why can't it be connected in the same way as the FRITZ!Fon? Is SIP the >> >>> same as VOIP?

    Oh! Is the FRITZ!Fon not DECT? Most are.
    If not and it's VoIP then do you know how its VoIP is configured?

    I expect most have a web interface


    Google thinks all FRITZ!Fon are DECT, not VoIP.

    But DECT and VOIP are not mutually exclusive, it's perfectly possible
    to have a VOIP system that uses DECT handsets. It's also possible to
    have both a DECT/VOIP system and a separate VOIP phone using the same >router (I've done it!). The router doesn't really know or care if a
    device that's connected to it is VOIP or any other protocol.

    I understood this (cordless) VOIP handset runs off the WiFi with
    nothing connected to the 'FON' port on the router - or are you saying
    the router may have DECT as well as WiFi built in?

    I think you understand correctly. The VOIP handset just requires a way to communicate with the internet which it gets by using WiFi to the router.
    As I said the router doesn't care really what's connected, it just
    provides a link between the VOIP handset and the internet.

    The FON port on the router is (I think) a built in VOIP 'endpoint' that
    allows you to connect an old POTS phone to it.

    I think some FRITZ routers may **also** be DECT base stations so they
    provide a way for DECT handsets to connect, through the VOIP
    'endpoint' in the router to the internet.
    --
    Chris Green
    -+
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Scott@newsgroups@gefion.myzen.co.uk to uk.telecom on Sat Oct 17 10:28:02 2026
    From Newsgroup: uk.telecom

    On Sat, 17 Oct 2026 08:47:20 +0100, The Natural Philosopher <tnp@invalid.invalid> wrote:

    On 17/10/2026 02:23, J. P. Gilliver wrote:
    In some discussion on this matter a while back (external ATAs were the
    main consideration at that point), some people in the discussion said
    that some ATAs could handle a variety of compression/encoding protocols,
    and some said you could choose the one you wanted to use.

    I THINK that is correct. My router has tunable options for VOIP, AIUI
    the endpoint VOIP units (whatever they are ) negotiate a common
    standard, or at least acceptable ones in both direction. Mine is
    currently set to 'prefer' an 8kbps codec. This gives excellent results
    but faster options are avialable


    (That
    discussion started out by comaparing the quality of VoIP to normal POTS,
    with some [people with hearing impairments] saying they couldn't get on
    with e. g. whatever mobile 'phones use, only normal 'phones; others
    pointed out that normal 'phones use an encoding/compression standard
    anyway, and even named it [I think it was a 5 or 6 character string of
    letters and numbers].)

    'Normal' phones use a 64kbps fixed TDM . Crude by today's standards but >very advanced when it first came out. I am fairly sure that conversion
    to and from analogue happens at the exchange.

    That is why modems could only ever reach 56Kbps or thereabouts and ISDN >lines were 64kbps digital

    UK backbone is/was built of links that are multiples of this speed,

    Then I think it moved to frame relay, but the basic encoding didn't change >VOIP phones use 'intelligent' codecs that can get te same or bvetter
    quality into e.g an 8kbps channel

    Mobile data rates are much much lower. Hundreds of calls need to be
    squeezed into a very limited RF spectrum. 8kbps is luxury. 1kbps is
    normal and in congested areas even less. To the point where it becomes >unintelligible.

    Mobile is not VOIP. There is - or was - no IP involved. Different
    standards to meet different limitations. Mobiles are massively bandwidth >limited, but even an ADSL links is way way faster than a mobile link
    *used* to be. I cant answer for 4G/5G

    So mobile is like VOIP is a completely false statement, Qualitry IS
    NOTHING like VOIP. Its like comparing Radio Caroline on the MW with a
    full power VHF radio signal

    True. Reception of 648 kHz is not great in Glasgow. Should the aerial
    be half the wavelength: 232 metres? Vertical or horizontal :-)
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Marco Moock@mm@dorfdsl.de to uk.telecom on Sat Oct 17 11:28:15 2026
    From Newsgroup: uk.telecom

    Am 16.10.26 um 22:49 schrieb The Natural Philosopher:

    Yes. essentially the fritzbox or the pure voiphone need to connect to a
    SIP server which as a record of their 'phone number' and registers an IP
    and port address ion it.

    The router has to allow incoming traffic to reach that port. Sometimes
    NAT will do it but mostly the router needs to map the frirzbox/voip
    phone-a ip address and port to a public ip address and port.

    My router contains the equoivalent of two fritz boxes as well as its
    normal fiunctions

    In use, to dial out, you contact the server with the number you want to contact, and that either tells you how to contact it directly via IP address/port, ifs its VOIP or directs you to a gateway to POTS or mobile services or proxies the connection to a remote number itself

    The service I use (dus.net in Germany) routes all the traffic via their servers, so I only contact them. The telephone companies want it that
    way - so they can charge for the calls.
    --
    Gru|f
    Marco

    Spam bitte an abfalleimer2001@stinkedores.dorfdsl.de
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Marco Moock@mm@dorfdsl.de to uk.telecom on Sat Oct 17 11:29:43 2026
    From Newsgroup: uk.telecom

    Am 16.10.26 um 18:16 schrieb Brian Gregory:
    You will need Fritzbox documentation to find out about configuring a
    VoIP phone to connect to and use the Fritzbox as a kind of switchboard rather than to connect directly to Zen.

    That can be configured in the web interface. You need to add the SIP
    account, then add a new telephone (VoIP) that gets its own credentials.
    Those will be entered on the actual VoIP phone.
    --
    Gru|f
    Marco

    Spam bitte an abfalleimer2001@stinkedores.dorfdsl.de
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Marco Moock@mm@dorfdsl.de to uk.telecom on Sat Oct 17 11:31:39 2026
    From Newsgroup: uk.telecom

    Am 17.10.26 um 10:49 schrieb Scott:
    On Fri, 16 Oct 2026 21:09:30 +0100, The Natural Philosopher <tnp@invalid.invalid> wrote:

    On 16/10/2026 13:03, Scott wrote:
    As it happens, it is a FRITZ!Box and Zen is my ISP. Does this mean I
    can plug it into a LAN port (not FON) and will it work out of the box?
    Does SIP phone require a power supply?

    The Fritzbox should have enough power to drive a basic analogue phone

    Yes it can but the audio quality is not very good (not as good at the cordless) and there is a loud buzzing noise.

    The buzzing noise might be interference from elsewhere, I have 2 analog
    phone on my FB, one via a very long cable in the wall to my office.

    If it is compatible with the SIP service it just needs a connection to
    your LAN, and some power.

    I can do that with the cordless but I wondered about a corded phone
    for my desk (with the option of headphones) given that the router is
    only 1 metre away.

    Some VoIP phones support PoE, but you need a PoE injector, as the
    FritzBox does not support powering devices via PoE.
    --
    Gru|f
    Marco

    Spam bitte an abfalleimer2001@stinkedores.dorfdsl.de
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From David Wade@g4ugm@dave.invalid to uk.telecom on Sat Oct 17 10:56:11 2026
    From Newsgroup: uk.telecom

    On 17/10/2026 10:06, Chris Green wrote:
    Scott <newsgroups@gefion.myzen.co.uk> wrote:
    On Sat, 17 Oct 2026 09:08:09 +0100, Chris Green <cl@isbd.net> wrote:

    Brian Gregory <void-invalid-dead-dontuse@email.invalid> wrote:
    On 16/10/2026 21:37, The Natural Philosopher wrote:
    On 16/10/2026 19:30, Brian Gregory wrote:
    On 16/10/2026 17:37, Scott wrote:
    On Fri, 16 Oct 2026 17:16:52 +0100, Brian Gregory
    <void-invalid-dead-dontuse@email.invalid> wrote:

    On 16/10/2026 16:40, Scott wrote:
    I don't know if this helps or hinders but I already have a cordless >>>>>>>>> VOIP phone (FRITZ!Fon) that links direct to the router (so I assume >>>>>>>>> the basic set-up is in place). Now I am thinking about a corded VOIP >>>>>>>>> (SIP) phone for my desk as the audio quality is not too good on the >>>>>>>>> traditional phone I am using.

    You will need Fritzbox documentation to find out about configuring a >>>>>>>> VoIP phone to connect to and use the Fritzbox as a kind of switchboard >>>>>>>> rather than to connect directly to Zen.

    Why can't it be connected in the same way as the FRITZ!Fon? Is SIP the >>>>>>> same as VOIP?

    Oh! Is the FRITZ!Fon not DECT? Most are.
    If not and it's VoIP then do you know how its VoIP is configured?

    I expect most have a web interface


    Google thinks all FRITZ!Fon are DECT, not VoIP.

    But DECT and VOIP are not mutually exclusive, it's perfectly possible
    to have a VOIP system that uses DECT handsets. It's also possible to
    have both a DECT/VOIP system and a separate VOIP phone using the same
    router (I've done it!). The router doesn't really know or care if a
    device that's connected to it is VOIP or any other protocol.

    I understood this (cordless) VOIP handset runs off the WiFi with
    nothing connected to the 'FON' port on the router - or are you saying
    the router may have DECT as well as WiFi built in?

    I think you understand correctly. The VOIP handset just requires a way to communicate with the internet which it gets by using WiFi to the router.
    As I said the router doesn't care really what's connected, it just
    provides a link between the VOIP handset and the internet.

    The FON port on the router is (I think) a built in VOIP 'endpoint' that allows you to connect an old POTS phone to it.

    I think some FRITZ routers may **also** be DECT base stations so they
    provide a way for DECT handsets to connect, through the VOIP
    'endpoint' in the router to the internet.

    The ones Zen supplies are....

    Dave
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From David Wade@g4ugm@dave.invalid to uk.telecom on Sat Oct 17 11:03:15 2026
    From Newsgroup: uk.telecom

    On 17/10/2026 09:49, Scott wrote:
    On Fri, 16 Oct 2026 21:09:30 +0100, The Natural Philosopher <tnp@invalid.invalid> wrote:

    On 16/10/2026 13:03, Scott wrote:
    As it happens, it is a FRITZ!Box and Zen is my ISP. Does this mean I
    can plug it into a LAN port (not FON) and will it work out of the box?
    Does SIP phone require a power supply?

    The Fritzbox should have enough power to drive a basic analogue phone

    Yes it can but the audio quality is not very good (not as good at the cordless) and there is a loud buzzing noise.

    That is very odd. I have my old house wiring and a DECT base station
    plugged into the analogue phone port on one of my Fritz routers and
    don't get any buzzing.

    I also have a Panasonic DECT handset paired with another of my Fritz
    router. Again no buzzing. Good quality.


    If it is compatible with the SIP service it just needs a connection to
    your LAN, and some power.

    I can do that with the cordless but I wondered about a corded phone
    for my desk (with the option of headphones) given that the router is
    only 1 metre away.

    DECT then no cord on the desk. Good handsfree. Cheap.

    Dave
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Richmond@dnomhcir@gmx.com to uk.telecom on Sat Oct 17 11:41:31 2026
    From Newsgroup: uk.telecom

    Brian Gregory <void-invalid-dead-dontuse@email.invalid> writes:

    However if you want to use a VoIP phone instead of an ISP provided ATA
    you'll need to find out the required settings for the phone and also
    how to disable the ATA in the router and configure it to pass the VoIP through to your VoIP phone.

    Presumably you could have a different number on the VOIP phone, and the
    router should route calls to the appropriate port, phone port 1 or 2, or
    the Ethernet port.

    Or if all phones had the same number, then the router would route
    traffic to the one which made the call.

    What would happen for incoming calls? Would all the phones rings?
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From The Natural Philosopher@tnp@invalid.invalid to uk.telecom on Sat Oct 17 11:47:22 2026
    From Newsgroup: uk.telecom

    On 17/10/2026 09:44, Scott wrote:
    I understood this (cordless) VOIP handset runs off the WiFi with
    nothing connected to the 'FON' port on the router - or are you saying
    the router may have DECT as well as WiFi built in?

    I think what he was saying is that there exist ethernet or wifi voip
    adapters that do not feed an analogue phone, but feed a dect style one,
    which isnt wifi as such.
    --
    There is nothing a fleet of dispatchable nuclear power plants cannot do
    that cannot be done worse and more expensively and with higher carbon emissions and more adverse environmental impact by adding intermittent renewable energy.

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Chris Green@cl@isbd.net to uk.telecom on Sat Oct 17 11:44:11 2026
    From Newsgroup: uk.telecom

    Scott <newsgroups@gefion.myzen.co.uk> wrote:
    If it is compatible with the SIP service it just needs a connection to >your LAN, and some power.

    I can do that with the cordless but I wondered about a corded phone
    for my desk (with the option of headphones) given that the router is
    only 1 metre away.

    I have a secondhand Yealink SIP-T42S IP phone which cost the princely sum
    of -u15.98, it works very nicely and can be configured to use multiple
    VOIP providers. It just needs a connection to the internet (normally via
    your router). It needs a wired connection. You can get a WiFi dongle for
    it but that gets you into a tangle of version numbers and compatibility
    so the wired connection is much easier (especially if it's close to the router).
    --
    Chris Green
    -+
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From The Natural Philosopher@tnp@invalid.invalid to uk.telecom on Sat Oct 17 11:49:24 2026
    From Newsgroup: uk.telecom

    On 17/10/2026 10:06, Andy Burns wrote:
    The Natural Philosopher wrote:

    Mobile is not VOIP. There is - or was - no IP involved.

    The only mobile that *isn't* VoIP is 2G.

    3G is gone.

    4G and 5G are pure IP networks, VoLTE is SIP/RTP over IP, VoNR is the equivalent for 5G.

    Granted, phones can for the short term choose to drop to 2G to do voice.

    However, the codecs in use are NOT the same as a POTS replacement VOIP
    phone uses
    --
    There is nothing a fleet of dispatchable nuclear power plants cannot do
    that cannot be done worse and more expensively and with higher carbon emissions and more adverse environmental impact by adding intermittent renewable energy.

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From The Natural Philosopher@tnp@invalid.invalid to uk.telecom on Sat Oct 17 11:50:50 2026
    From Newsgroup: uk.telecom

    On 17/10/2026 10:28, Scott wrote:
    On Sat, 17 Oct 2026 08:47:20 +0100, The Natural Philosopher <tnp@invalid.invalid> wrote:

    So mobile is like VOIP is a completely false statement, Qualitry IS
    NOTHING like VOIP. Its like comparing Radio Caroline on the MW with a
    full power VHF radio signal

    True. Reception of 648 kHz is not great in Glasgow. Should the aerial
    be half the wavelength: 232 metres? Vertical or horizontal :-)

    Seriously yes. Horizontally, strung between poles like a telephone line
    --
    There is nothing a fleet of dispatchable nuclear power plants cannot do
    that cannot be done worse and more expensively and with higher carbon emissions and more adverse environmental impact by adding intermittent renewable energy.

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Chris Green@cl@isbd.net to uk.telecom on Sat Oct 17 12:15:25 2026
    From Newsgroup: uk.telecom

    Richmond <dnomhcir@gmx.com> wrote:
    Brian Gregory <void-invalid-dead-dontuse@email.invalid> writes:

    However if you want to use a VoIP phone instead of an ISP provided ATA you'll need to find out the required settings for the phone and also
    how to disable the ATA in the router and configure it to pass the VoIP through to your VoIP phone.

    Presumably you could have a different number on the VOIP phone, and the router should route calls to the appropriate port, phone port 1 or 2, or
    the Ethernet port.

    If it's a VOIP phone then the router isn't involved at all except to the
    extent of sending and receiving the VOIP data packets.


    Or if all phones had the same number, then the router would route
    traffic to the one which made the call.

    See above, the router isn't involved. This is one of the difficulties
    when using VOIP phones via a typical home router that does NAT. There
    isn't a simple way for the packets of data coming 'back' to find the VOIP handset. The A&A website has a better explanation of this problem than I
    will ever manage, and A&A dislike NAT for this very reason.


    What would happen for incoming calls? Would all the phones rings?

    If there's more than one VOIP phone registered to a VOIP number then all
    of them will ring (or receive the call anyway). They don't have to be connected via the same router or even be in the same country. I have a
    VOIP phone on my boat in France which receives calls at the same time as
    our VOIP phones at home in the UK as it's registered with the same number
    at the same VOIP provider.
    --
    Chris Green
    -+
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Richmond@dnomhcir@gmx.com to uk.telecom on Sat Oct 17 12:29:14 2026
    From Newsgroup: uk.telecom

    Chris Green <cl@isbd.net> writes:

    Richmond <dnomhcir@gmx.com> wrote:
    Brian Gregory <void-invalid-dead-dontuse@email.invalid> writes:

    However if you want to use a VoIP phone instead of an ISP provided ATA
    you'll need to find out the required settings for the phone and also
    how to disable the ATA in the router and configure it to pass the VoIP
    through to your VoIP phone.

    Presumably you could have a different number on the VOIP phone, and the
    router should route calls to the appropriate port, phone port 1 or 2, or
    the Ethernet port.

    If it's a VOIP phone then the router isn't involved at all except to the extent of sending and receiving the VOIP data packets.

    Well that's quite a lot of involvement isn't it?



    Or if all phones had the same number, then the router would route
    traffic to the one which made the call.

    See above, the router isn't involved. This is one of the difficulties
    when using VOIP phones via a typical home router that does NAT. There
    isn't a simple way for the packets of data coming 'back' to find the VOIP handset. The A&A website has a better explanation of this problem than I will ever manage, and A&A dislike NAT for this very reason.

    My router is involved. I have two phones with two different telephone
    numbers plugged into the two phone sockets on the router. To get this to
    work I enabled SIP ALG (which everyone hates). But it works. I think it
    would also work to route calls to a VOIP phone connected to the ethernet
    port but I haven't tested it. The phone would have its own ipv6 address
    so it shouldn't be difficult.

    AA says different things about SIP ALG, see here:

    https://support.aa.net.uk/VoIP_Firewall




    What would happen for incoming calls? Would all the phones rings?

    If there's more than one VOIP phone registered to a VOIP number then all
    of them will ring (or receive the call anyway). They don't have to be connected via the same router or even be in the same country. I have a
    VOIP phone on my boat in France which receives calls at the same time as
    our VOIP phones at home in the UK as it's registered with the same number
    at the same VOIP provider.

    I found Voipfone did not necessarily ring on the mobile app (softphone)
    but this is probably due to the configuration needing to keep it alive.
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From David Wade@g4ugm@dave.invalid to uk.telecom on Sat Oct 17 12:47:53 2026
    From Newsgroup: uk.telecom

    On 17/10/2026 12:15, Chris Green wrote:
    Richmond <dnomhcir@gmx.com> wrote:
    Brian Gregory <void-invalid-dead-dontuse@email.invalid> writes:

    However if you want to use a VoIP phone instead of an ISP provided ATA
    you'll need to find out the required settings for the phone and also
    how to disable the ATA in the router and configure it to pass the VoIP
    through to your VoIP phone.

    Presumably you could have a different number on the VOIP phone, and the
    router should route calls to the appropriate port, phone port 1 or 2, or
    the Ethernet port.

    If it's a VOIP phone then the router isn't involved at all except to the extent of sending and receiving the VOIP data packets.


    Assuming its a plain router, yes, but my Fritz!Box also acts as a SIP
    server so you can build a mini home PABX.



    Or if all phones had the same number, then the router would route
    traffic to the one which made the call.

    See above, the router isn't involved. This is one of the difficulties
    when using VOIP phones via a typical home router that does NAT. There
    isn't a simple way for the packets of data coming 'back' to find the VOIP handset. The A&A website has a better explanation of this problem than I will ever manage, and A&A dislike NAT for this very reason.

    What would happen for incoming calls? Would all the phones rings?

    If there's more than one VOIP phone registered to a VOIP number then all
    of them will ring (or receive the call anyway). They don't have to be connected via the same router or even be in the same country. I have a
    VOIP phone on my boat in France which receives calls at the same time as
    our VOIP phones at home in the UK as it's registered with the same number
    at the same VOIP provider.


    I have a similar setup in Spain

    Dave
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Scott@newsgroups@gefion.myzen.co.uk to uk.telecom on Sat Oct 17 12:49:34 2026
    From Newsgroup: uk.telecom

    On Sat, 17 Oct 2026 10:56:11 +0100, David Wade <g4ugm@dave.invalid>
    wrote:

    On 17/10/2026 10:06, Chris Green wrote:
    Scott <newsgroups@gefion.myzen.co.uk> wrote:
    On Sat, 17 Oct 2026 09:08:09 +0100, Chris Green <cl@isbd.net> wrote:

    Brian Gregory <void-invalid-dead-dontuse@email.invalid> wrote:
    On 16/10/2026 21:37, The Natural Philosopher wrote:
    On 16/10/2026 19:30, Brian Gregory wrote:
    On 16/10/2026 17:37, Scott wrote:
    On Fri, 16 Oct 2026 17:16:52 +0100, Brian Gregory
    <void-invalid-dead-dontuse@email.invalid> wrote:

    On 16/10/2026 16:40, Scott wrote:
    I don't know if this helps or hinders but I already have a cordless >>>>>>>>>> VOIP phone (FRITZ!Fon) that links direct to the router (so I assume >>>>>>>>>> the basic set-up is in place). Now I am thinking about a corded VOIP >>>>>>>>>> (SIP) phone for my desk as the audio quality is not too good on the >>>>>>>>>> traditional phone I am using.

    You will need Fritzbox documentation to find out about configuring a >>>>>>>>> VoIP phone to connect to and use the Fritzbox as a kind of switchboard
    rather than to connect directly to Zen.

    Why can't it be connected in the same way as the FRITZ!Fon? Is SIP the >>>>>>>> same as VOIP?

    Oh! Is the FRITZ!Fon not DECT? Most are.
    If not and it's VoIP then do you know how its VoIP is configured? >>>>>>>
    I expect most have a web interface


    Google thinks all FRITZ!Fon are DECT, not VoIP.

    But DECT and VOIP are not mutually exclusive, it's perfectly possible
    to have a VOIP system that uses DECT handsets. It's also possible to
    have both a DECT/VOIP system and a separate VOIP phone using the same
    router (I've done it!). The router doesn't really know or care if a
    device that's connected to it is VOIP or any other protocol.

    I understood this (cordless) VOIP handset runs off the WiFi with
    nothing connected to the 'FON' port on the router - or are you saying
    the router may have DECT as well as WiFi built in?

    I think you understand correctly. The VOIP handset just requires a way to
    communicate with the internet which it gets by using WiFi to the router.
    As I said the router doesn't care really what's connected, it just
    provides a link between the VOIP handset and the internet.

    The FON port on the router is (I think) a built in VOIP 'endpoint' that
    allows you to connect an old POTS phone to it.

    I think some FRITZ routers may **also** be DECT base stations so they
    provide a way for DECT handsets to connect, through the VOIP
    'endpoint' in the router to the internet.

    The ones Zen supplies are....

    Does this mean my FRITZ!Fon is DECT and not WiFi? Does this improve or
    worsen its range?
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Scott@newsgroups@gefion.myzen.co.uk to uk.telecom on Sat Oct 17 12:56:13 2026
    From Newsgroup: uk.telecom

    On Sat, 17 Oct 2026 11:50:50 +0100, The Natural Philosopher <tnp@invalid.invalid> wrote:

    On 17/10/2026 10:28, Scott wrote:
    On Sat, 17 Oct 2026 08:47:20 +0100, The Natural Philosopher
    <tnp@invalid.invalid> wrote:

    So mobile is like VOIP is a completely false statement, Qualitry IS
    NOTHING like VOIP. Its like comparing Radio Caroline on the MW with a
    full power VHF radio signal

    True. Reception of 648 kHz is not great in Glasgow. Should the aerial
    be half the wavelength: 232 metres? Vertical or horizontal :-)

    Seriously yes. Horizontally, strung between poles like a telephone line

    It was serious because I am puzzled. When I visited Droitwich I was
    told the polarisation was vertical. Is MW different in this respect?
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From The Natural Philosopher@tnp@invalid.invalid to uk.telecom on Sat Oct 17 13:32:56 2026
    From Newsgroup: uk.telecom

    On 17/10/2026 12:56, Scott wrote:
    On Sat, 17 Oct 2026 11:50:50 +0100, The Natural Philosopher <tnp@invalid.invalid> wrote:

    On 17/10/2026 10:28, Scott wrote:
    On Sat, 17 Oct 2026 08:47:20 +0100, The Natural Philosopher
    <tnp@invalid.invalid> wrote:

    So mobile is like VOIP is a completely false statement, Qualitry IS
    NOTHING like VOIP. Its like comparing Radio Caroline on the MW with a
    full power VHF radio signal

    True. Reception of 648 kHz is not great in Glasgow. Should the aerial
    be half the wavelength: 232 metres? Vertical or horizontal :-)

    Seriously yes. Horizontally, strung between poles like a telephone line

    It was serious because I am puzzled. When I visited Droitwich I was
    told the polarisation was vertical. Is MW different in this respect?

    I dunno to be honest. I thought it was
    --
    The New Left are the people they warned you about.

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Marco Moock@mm@dorfdsl.de to uk.telecom on Sat Oct 17 15:30:46 2026
    From Newsgroup: uk.telecom

    Am 17.10.26 um 12:03 schrieb David Wade:
    That is very odd. I have my old house wiring and a DECT base station
    plugged into the analogue phone port on one of my Fritz routers and
    don't get any buzzing.

    In the basement a Cisco router is sitting next to an analog phone and
    creates interference that is audible on the phone.
    --
    Gru|f
    Marco

    Spam bitte an abfalleimer2001@stinkedores.dorfdsl.de
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Marco Moock@mm@dorfdsl.de to uk.telecom on Sat Oct 17 15:48:04 2026
    From Newsgroup: uk.telecom

    Am 16.10.26 um 22:19 schrieb The Natural Philosopher:
    On 16/10/2026 17:41, Andy Burns wrote:
    Scott wrote:

    Why can't it be connected in the same way as the FRITZ!Fon? Is SIP the
    same as VOIP?

    Basically yes ... SIP is the signalling protocol and RTP is used for
    the actual audio/video.
    AIUI the sip server simply registers your phone number-a IP address and
    port number, so when someone wants to connect to your phone they know
    which port to access on which IP address

    It may act as a proxy too,

    But ideally it takes no part in sending voice packets
    Its more like a DNS server than a router.

    So e.g if you want to phone someone it says 'contact 176.4.35.1 on port 9900' and so you do, and the other end says 'hi im a voip line' and you
    talk direct

    If its being mapped to a land line it needs a special gateway, but since everyone is going VOIP I expect less use of that. More likely a gateway
    to mobile.

    That is what costs money. Voip to Voip should be free

    That is what is was meant to be - but the telephone companies did not
    like that, as this means they cannot charge per minute for a call and
    compared to the other traffic VoIP is just a small part, so they decided
    to route the calls through their infrastructure.
    --
    Gru|f
    Marco

    Spam bitte an abfalleimer2001@stinkedores.dorfdsl.de
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From The Natural Philosopher@tnp@invalid.invalid to uk.telecom on Sat Oct 17 15:11:16 2026
    From Newsgroup: uk.telecom

    On 17/10/2026 13:32, The Natural Philosopher wrote:
    On 17/10/2026 12:56, Scott wrote:
    On Sat, 17 Oct 2026 11:50:50 +0100, The Natural Philosopher
    <tnp@invalid.invalid> wrote:

    On 17/10/2026 10:28, Scott wrote:
    On Sat, 17 Oct 2026 08:47:20 +0100, The Natural Philosopher
    <tnp@invalid.invalid> wrote:

    So mobile is like VOIP is a completely false statement, Qualitry IS
    NOTHING like VOIP. Its like comparing Radio Caroline on the MW with a >>>>> full power VHF radio signal

    True. Reception of 648 kHz is not great in Glasgow. Should the aerial
    be half the wavelength: 232 metres? Vertical or horizontal :-)

    Seriously yes. Horizontally, strung between poles like a telephone line

    It was serious because I am puzzled. When I visited Droitwich I was
    told the polarisation was vertical. Is MW different in this respect?

    I dunno to be honest. I thought it was

    I did a bit more research. It is indeed vertical. So whip antennae work.
    Well you will just have to bottom load as tall a bit of metal as you can
    erect :-)
    --
    Socialism is the philosophy of failure, the creed of ignorance and the
    gospel of envy.

    Its inherent virtue is the equal sharing of misery.

    Winston Churchill


    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From David Wade@g4ugm@dave.invalid to uk.telecom on Sat Oct 17 15:59:36 2026
    From Newsgroup: uk.telecom

    On 17/10/2026 12:49, Scott wrote:
    On Sat, 17 Oct 2026 10:56:11 +0100, David Wade <g4ugm@dave.invalid>
    wrote:

    On 17/10/2026 10:06, Chris Green wrote:
    Scott <newsgroups@gefion.myzen.co.uk> wrote:
    On Sat, 17 Oct 2026 09:08:09 +0100, Chris Green <cl@isbd.net> wrote:

    Brian Gregory <void-invalid-dead-dontuse@email.invalid> wrote:
    On 16/10/2026 21:37, The Natural Philosopher wrote:
    On 16/10/2026 19:30, Brian Gregory wrote:
    On 16/10/2026 17:37, Scott wrote:
    On Fri, 16 Oct 2026 17:16:52 +0100, Brian Gregory
    <void-invalid-dead-dontuse@email.invalid> wrote:

    On 16/10/2026 16:40, Scott wrote:
    I don't know if this helps or hinders but I already have a cordless >>>>>>>>>>> VOIP phone (FRITZ!Fon) that links direct to the router (so I assume >>>>>>>>>>> the basic set-up is in place). Now I am thinking about a corded VOIP
    (SIP) phone for my desk as the audio quality is not too good on the >>>>>>>>>>> traditional phone I am using.

    You will need Fritzbox documentation to find out about configuring a >>>>>>>>>> VoIP phone to connect to and use the Fritzbox as a kind of switchboard
    rather than to connect directly to Zen.

    Why can't it be connected in the same way as the FRITZ!Fon? Is SIP the
    same as VOIP?

    Oh! Is the FRITZ!Fon not DECT? Most are.
    If not and it's VoIP then do you know how its VoIP is configured? >>>>>>>>
    I expect most have a web interface


    Google thinks all FRITZ!Fon are DECT, not VoIP.

    But DECT and VOIP are not mutually exclusive, it's perfectly possible >>>>> to have a VOIP system that uses DECT handsets. It's also possible to >>>>> have both a DECT/VOIP system and a separate VOIP phone using the same >>>>> router (I've done it!). The router doesn't really know or care if a >>>>> device that's connected to it is VOIP or any other protocol.

    I understood this (cordless) VOIP handset runs off the WiFi with
    nothing connected to the 'FON' port on the router - or are you saying
    the router may have DECT as well as WiFi built in?

    I think you understand correctly. The VOIP handset just requires a way to >>> communicate with the internet which it gets by using WiFi to the router. >>> As I said the router doesn't care really what's connected, it just
    provides a link between the VOIP handset and the internet.

    The FON port on the router is (I think) a built in VOIP 'endpoint' that >>> allows you to connect an old POTS phone to it.

    I think some FRITZ routers may **also** be DECT base stations so they
    provide a way for DECT handsets to connect, through the VOIP
    'endpoint' in the router to the internet.

    The ones Zen supplies are....

    Does this mean my FRITZ!Fon is DECT and not WiFi?

    Yes.

    Does this improve or
    worsen its range?

    I believe it improves the range. One of the extensions to the DECT
    protocol also provides shared phone books for example.

    Dave
    G4UGM
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From J. P. Gilliver@G6JPG@255soft.uk to uk.telecom on Sun Oct 18 03:43:32 2026
    From Newsgroup: uk.telecom

    On 2026/10/17 11:50:50, The Natural Philosopher wrote:
    On 17/10/2026 10:28, Scott wrote:
    On Sat, 17 Oct 2026 08:47:20 +0100, The Natural Philosopher
    <tnp@invalid.invalid> wrote:

    So mobile is like VOIP is a completely false statement, Qualitry IS
    NOTHING like VOIP. Its like comparing Radio Caroline on the MW with a
    full power VHF radio signal

    True. Reception of 648 kHz is not great in Glasgow. Should the aerial
    be half the wavelength: 232 metres? Vertical or horizontal :-)

    Seriously yes. Horizontally, strung between poles like a telephone line


    With the feed point in the middle, not at one end.
    --
    J. P. Gilliver. UMRA: 1960/<1985 MB++G()ALIS-Ch++(p)Ar++T+H+Sh0!:`)DNAf

    Should you long for the pitter-patter of tiny feet ...
    ... buy a dog. It's cheaper, and you get more feet.
    - (Attributed to) Rita Rudner
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From J. P. Gilliver@G6JPG@255soft.uk to uk.telecom on Sun Oct 18 03:51:23 2026
    From Newsgroup: uk.telecom

    (We should be including uk.tech.broadcast!)
    On 2026/10/17 15:11:16, The Natural Philosopher wrote:
    On 17/10/2026 13:32, The Natural Philosopher wrote:
    On 17/10/2026 12:56, Scott wrote:
    On Sat, 17 Oct 2026 11:50:50 +0100, The Natural Philosopher
    <tnp@invalid.invalid> wrote:

    On 17/10/2026 10:28, Scott wrote:
    On Sat, 17 Oct 2026 08:47:20 +0100, The Natural Philosopher
    <tnp@invalid.invalid> wrote:

    So mobile is like VOIP is a completely false statement, Qualitry IS >>>>>> NOTHING like VOIP. Its like comparing Radio Caroline on the MW with a >>>>>> full power VHF radio signal

    True. Reception of 648 kHz is not great in Glasgow. Should the aerial >>>>> be half the wavelength: 232 metres? Vertical or horizontal :-)

    Seriously yes. Horizontally, strung between poles like a telephone line >>>
    It was serious because I am puzzled. When I visited Droitwich I was
    told the polarisation was vertical. Is MW different in this respect?

    I dunno to be honest. I thought it was

    I did a bit more research. It is indeed vertical. So whip antennae work. Well you will just have to bottom load as tall a bit of metal as you can erect :-)

    For a medium-wave transmitter, it's just about possible - for some
    stations - to actually erect a half-wave dipole to transmit from; for
    obvious reasons, they tend to be horizontal. For very long waves, it is sometimes not actually possible to do that, so the aerial that you _can_
    erect becomes a "capacity hat", and the majority of the current in the
    aerial is in the feedline going up to it - which is vertical. I don't
    know if Droitwich was actually big enough to be a horizontal half-wave
    at (approx.) 1500 metres; certainly the ones they use to talk to
    submarines (60, 19.6, and 16 kHz) are not.
    --
    J. P. Gilliver. UMRA: 1960/<1985 MB++G()ALIS-Ch++(p)Ar++T+H+Sh0!:`)DNAf
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From J. P. Gilliver@G6JPG@255soft.uk to uk.telecom on Sun Oct 18 04:06:56 2026
    From Newsgroup: uk.telecom

    On 2026/10/17 12:15:25, Chris Green wrote:
    []
    If there's more than one VOIP phone registered to a VOIP number then all
    of them will ring (or receive the call anyway). They don't have to be connected via the same router or even be in the same country. I have a> VOIP phone on my boat in France which receives calls at the same time as
    our VOIP phones at home in the UK as it's registered with the same number
    at the same VOIP provider.

    If I VoIP-call your number, presumably my VoIP packets are not sent to
    every VoIP 'phone in the country; so how does the network arrange that
    they _are_ sent to both your 'phone(s) at home, and to your boat in France? Presumably it's via some systen similar to normal internet use - if I'm accessing mail or a web server, the packets therefrom are routed only to
    me (I've never actually given much thought to how _that_ works, but it
    does). But in those cases, they're only going to one of me, in/at one
    location.
    --
    J. P. Gilliver. UMRA: 1960/<1985 MB++G()ALIS-Ch++(p)Ar++T+H+Sh0!:`)DNAf
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Scott@newsgroups@gefion.myzen.co.uk to uk.telecom on Sun Oct 18 10:21:16 2026
    From Newsgroup: uk.telecom

    On Sun, 18 Oct 2026 03:43:32 +0100, "J. P. Gilliver"
    <G6JPG@255soft.uk> wrote:

    On 2026/10/17 11:50:50, The Natural Philosopher wrote:
    On 17/10/2026 10:28, Scott wrote:
    On Sat, 17 Oct 2026 08:47:20 +0100, The Natural Philosopher
    <tnp@invalid.invalid> wrote:

    So mobile is like VOIP is a completely false statement, Qualitry IS
    NOTHING like VOIP. Its like comparing Radio Caroline on the MW with a
    full power VHF radio signal

    True. Reception of 648 kHz is not great in Glasgow. Should the aerial
    be half the wavelength: 232 metres? Vertical or horizontal :-)

    Seriously yes. Horizontally, strung between poles like a telephone line


    With the feed point in the middle, not at one end.

    The bastard - my dad never told me that when I was a teenager.
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From The Natural Philosopher@tnp@invalid.invalid to uk.telecom on Sun Oct 18 10:55:25 2026
    From Newsgroup: uk.telecom

    On 18/10/2026 04:06, J. P. Gilliver wrote:
    On 2026/10/17 12:15:25, Chris Green wrote:
    []
    If there's more than one VOIP phone registered to a VOIP number then all
    of them will ring (or receive the call anyway). They don't have to be
    connected via the same router or even be in the same country. I have a
    VOIP phone on my boat in France which receives calls at the same time as
    our VOIP phones at home in the UK as it's registered with the same number
    at the same VOIP provider.

    If I VoIP-call your number, presumably my VoIP packets are not sent to
    every VoIP 'phone in the country; so how does the network arrange that
    they _are_ sent to both your 'phone(s) at home, and to your boat in France?

    Presumably it's via some systen similar to normal internet use - if I'm accessing mail or a web server, the packets therefrom are routed only to
    me (I've never actually given much thought to how _that_ works, but it
    does). But in those cases, they're only going to one of me, in/at one location.

    AIUI the SIP servers are there to turn telephone number into IP
    addresses. More that one IP address per number is permissible

    The first one to pick up gets the conversation
    As an side, this whole area of IP protocol SIP and STUN servers is very
    poorly documented on the Net

    'don't worry your pretty little heads about how it works, this us how to
    use it'
    --
    Microsoft : the best reason to go to Linux that ever existed.

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Theo@theom+news@chiark.greenend.org.uk to uk.telecom on Sun Oct 18 11:11:38 2026
    From Newsgroup: uk.telecom

    Richmond <dnomhcir@gmx.com> wrote:

    I found Voipfone did not necessarily ring on the mobile app (softphone)
    but this is probably due to the configuration needing to keep it alive.

    Yes, it's a PITA on mobiles because of the way they don't like running background apps and holding connections open, in order to save battery.
    There are various workarounds depending on the platform (Android or iOS),
    and some apps are better than others.

    Theo
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From snipeco.2@snipeco.2@gmail.com (Sn!pe) to uk.telecom on Sun Oct 18 13:20:26 2026
    From Newsgroup: uk.telecom

    Scott <newsgroups@gefion.myzen.co.uk> wrote:

    On Sun, 18 Oct 2026 03:43:32 +0100, "J. P. Gilliver"
    <G6JPG@255soft.uk> wrote:

    On 2026/10/17 11:50:50, The Natural Philosopher wrote:
    On 17/10/2026 10:28, Scott wrote:
    On Sat, 17 Oct 2026 08:47:20 +0100, The Natural Philosopher
    <tnp@invalid.invalid> wrote:

    So mobile is like VOIP is a completely false statement, Qualitry IS
    NOTHING like VOIP. Its like comparing Radio Caroline on the MW with a >>>> full power VHF radio signal

    True. Reception of 648 kHz is not great in Glasgow. Should the aerial
    be half the wavelength: 232 metres? Vertical or horizontal :-)

    Seriously yes. Horizontally, strung between poles like a telephone line


    With the feed point in the middle, not at one end.


    The bastard - my dad never told me that when I was a teenager.


    End-fed long wires (e.g. 'inverted L' with an ATU) work quite well for receiving but they're not recommended for transmitting because the
    end of the antenna is a high impedance point and feeding there results
    in lots of RF in the shack. It is possible to mitigate this somewhat by
    the use of a counterpoise and tuning against that rather than against
    earth.

    The centre point of a half-wave antenna, where current is greatest
    and most radiation occurs, should ideally be as high as possible.
    To achieve this, centre-fed 'inverted-V' antennas are popular.
    --
    Sn!pe, birdbrain. My pet rock Gordon just is.

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Spike@aero.spike@mail.com to uk.telecom on Sun Oct 18 12:54:09 2026
    From Newsgroup: uk.telecom

    Sn!pe <snipeco.2@gmail.com> wrote:

    End-fed long wires (e.g. 'inverted L' with an ATU) work quite well for receiving but they're not recommended for transmitting because the
    end of the antenna is a high impedance point and feeding there results
    in lots of RF in the shack. It is possible to mitigate this somewhat by
    the use of a counterpoise and tuning against that rather than against
    earth.

    I think that is misleading. Inverted-L antennas are popular on the 160m and
    80m Amateur bands, obviously for transmitting and receiving, and there is
    no reason why they cannot be used for MW reception.

    An ATU is necessary for transmitting and highly recommended for receiving.
    Its function is to transform the low impedance (50 ohm) of the feeder to
    the complex impedance of the antenna, and a properly designed system wonrCOt bring RF back into the shack.

    As these antennas tend to electrically short, they need to work against a ground system, such as surface radials, but a good connection to Earth
    (ground rod, etc) is necessary to bleed off static.

    The centre point of a half-wave antenna, where current is greatest
    and most radiation occurs, should ideally be as high as possible.
    To achieve this, centre-fed 'inverted-V' antennas are popular.

    Inverted-V antennas tend to be used when resonant.
    --
    Spike
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Brian Gregory@void-invalid-dead-dontuse@email.invalid to uk.telecom on Sun Oct 18 14:06:19 2026
    From Newsgroup: uk.telecom

    On 17/10/2026 13:32, The Natural Philosopher wrote:
    On 17/10/2026 12:56, Scott wrote:
    On Sat, 17 Oct 2026 11:50:50 +0100, The Natural Philosopher
    <tnp@invalid.invalid> wrote:

    On 17/10/2026 10:28, Scott wrote:
    On Sat, 17 Oct 2026 08:47:20 +0100, The Natural Philosopher
    <tnp@invalid.invalid> wrote:

    So mobile is like VOIP is a completely false statement, Qualitry IS
    NOTHING like VOIP. Its like comparing Radio Caroline on the MW with a >>>>> full power VHF radio signal

    True. Reception of 648 kHz is not great in Glasgow. Should the aerial
    be half the wavelength: 232 metres? Vertical or horizontal :-)

    Seriously yes. Horizontally, strung between poles like a telephone line

    It was serious because I am puzzled. When I visited Droitwich I was
    told the polarisation was vertical. Is MW different in this respect?

    I dunno to be honest. I thought it was


    Long and Medium waves are normally vertically polarised.
    Check with a radio that uses a ferrite rod. You need a horizontal
    ferrite rod to receive vertically polarised. If you turn the ferrite rod vertically you usually don't receive much at all.

    But even if you somehow manage to transmit horizontally polarised medium
    wave I think I'm right in saying signals carried by ground wave will end
    up mainly vertically polarised and those carried by sky wave will not
    stay horizontally polarised and end up as a mixed or continually
    changing polarisation.
    --
    Brian Gregory (in England).
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Brian Gregory@void-invalid-dead-dontuse@email.invalid to uk.telecom on Sun Oct 18 14:10:11 2026
    From Newsgroup: uk.telecom

    On 17/10/2026 09:44, Scott wrote:
    I understood this (cordless) VOIP handset runs off the WiFi with
    nothing connected to the 'FON' port on the router - or are you saying
    the router may have DECT as well as WiFi built in?

    Um yes. AIUI Fritz boxes have DECT built in.
    --
    Brian Gregory (in England).
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Brian Gregory@void-invalid-dead-dontuse@email.invalid to uk.telecom on Sun Oct 18 14:23:47 2026
    From Newsgroup: uk.telecom

    On 18/10/2026 10:21, Scott wrote:
    On Sun, 18 Oct 2026 03:43:32 +0100, "J. P. Gilliver"
    <G6JPG@255soft.uk> wrote:

    On 2026/10/17 11:50:50, The Natural Philosopher wrote:
    On 17/10/2026 10:28, Scott wrote:
    On Sat, 17 Oct 2026 08:47:20 +0100, The Natural Philosopher
    <tnp@invalid.invalid> wrote:

    So mobile is like VOIP is a completely false statement, Qualitry IS
    NOTHING like VOIP. Its like comparing Radio Caroline on the MW with a >>>>> full power VHF radio signal

    True. Reception of 648 kHz is not great in Glasgow. Should the aerial
    be half the wavelength: 232 metres? Vertical or horizontal :-)

    Seriously yes. Horizontally, strung between poles like a telephone line


    With the feed point in the middle, not at one end.

    The bastard - my dad never told me that when I was a teenager.

    This would be silly. To work well it would need to be so far above the
    ground that it'd be ridiculously impractical.

    Do what everyone else does and use the earth as one half and a wire as
    the other half. Or use a vertical loop aerial with one side aimed at the transmitter so the direction of the signal is in the plane of the loop.
    --
    Brian Gregory (in England).
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From snipeco.2@snipeco.2@gmail.com (Sn!pe) to uk.telecom on Sun Oct 18 14:24:53 2026
    From Newsgroup: uk.telecom

    Spike <aero.spike@mail.com> wrote:

    Sn!pe <snipeco.2@gmail.com> wrote:

    End-fed long wires (e.g. 'inverted L' with an ATU) work quite well for receiving but they're not recommended for transmitting because the
    end of the antenna is a high impedance point and feeding there results
    in lots of RF in the shack. It is possible to mitigate this somewhat by the use of a counterpoise and tuning against that rather than against earth.


    I think that is misleading. Inverted-L antennas are popular on the 160m and 80m Amateur bands, obviously for transmitting and receiving, and there is
    no reason why they cannot be used for MW reception.


    yes, of course.


    An ATU is necessary for transmitting and highly recommended for receiving. Its function is to transform the low impedance (50 ohm) of the feeder to
    the complex impedance of the antenna, and a properly designed system won't bring RF back into the shack.


    For RX-ing, an ATU's main function is to bring a random length of wet
    string into resonance. I don't dispute what you say about TX-ing.


    As these antennas tend to electrically short, they need to work against a ground system, such as surface radials, but a good connection to Earth (ground rod, etc) is necessary to bleed off static.


    The centre point of a half-wave antenna, where current is greatest
    and most radiation occurs, should ideally be as high as possible.
    To achieve this, centre-fed 'inverted-V' antennas are popular.


    Inverted-V antennas tend to be used when resonant.


    I'd say invariably, otherwise it would be very difficult to match its
    impedance to the feeder.

    To be honest, I'd forgotten that this discussion is about receiving MW,
    which brings us back to a random length of wet string. An ATU could be
    very useful and simple to implement.
    --
    Sn!pe, birdbrain. My pet rock Gordon just is.

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Marco Moock@mm@dorfdsl.de to uk.telecom on Sun Oct 18 15:29:01 2026
    From Newsgroup: uk.telecom

    Am 16.10.26 um 22:39 schrieb The Natural Philosopher:
    On 16/10/2026 19:34, Marco Moock wrote:
    Am 16.10.26 um 13:03 schrieb The Natural Philosopher:
    On 16/10/2026 10:49, Marco Moock wrote:
    Am 16.10.26 um 11:05 schrieb Richmond:
    Does the sound quality of VOIP depend on the ISPs network and the
    compression protocol it accepts? and also the recipients network.

    Of course. There are different codecs and your ISP might convert
    them if needed.

    The ISP is not involved in inspeccting packets passing through it or
    changing their protocols.

    As many people use the VoIP service from their ISP, I used that term.
    In case they use something else, that service will do the VoIP stuff.
    How is such a service provider properly called?

    The codecs in use are a function of the endpoints, which are other
    VOIP phones

    VOIP has NOTHING to do with the ISP at all. Unless they are running
    their own SIP server and/or POTS gateway

    They do that and most users use such a service. Direct VOIP calling is
    possible, but no normal users uses that. There was an idea to use DNS
    to get the remote's IP, but the telephone companies didn't like that.

    Or shuffling packet queus based on whether there is a viOPp packet in
    them


    The recipient's device and used codec is also relevant, as the
    lowest standard will define the speech quality.


    That is ALL that is relevant, that and the bandwidth, packet loss
    and latency between the devices

    In case there is a mismatch, a conversion needs to be done. Depending
    on how the telephone companies route the phone traffic, they might
    need to change to a lower codec.

    The end points negotiate that. And most voip to voip does not involve
    the SIP server
    VOIPto other shit involves and expensive VOIP gateway.

    I do use VoIP and it works as I explained here, even when other
    operation modes exist.

    E2E VoIP was never a big thing here.
    --
    Gru|f
    Marco

    Spam bitte an abfalleimer2001@stinkedores.dorfdsl.de
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Scott@newsgroups@gefion.myzen.co.uk to uk.telecom on Sun Oct 18 16:46:45 2026
    From Newsgroup: uk.telecom

    On Sun, 18 Oct 2026 14:23:47 +0100, Brian Gregory <void-invalid-dead-dontuse@email.invalid> wrote:

    On 18/10/2026 10:21, Scott wrote:
    On Sun, 18 Oct 2026 03:43:32 +0100, "J. P. Gilliver"
    <G6JPG@255soft.uk> wrote:

    On 2026/10/17 11:50:50, The Natural Philosopher wrote:
    On 17/10/2026 10:28, Scott wrote:
    On Sat, 17 Oct 2026 08:47:20 +0100, The Natural Philosopher
    <tnp@invalid.invalid> wrote:

    So mobile is like VOIP is a completely false statement, Qualitry IS >>>>>> NOTHING like VOIP. Its like comparing Radio Caroline on the MW with a >>>>>> full power VHF radio signal

    True. Reception of 648 kHz is not great in Glasgow. Should the aerial >>>>> be half the wavelength: 232 metres? Vertical or horizontal :-)

    Seriously yes. Horizontally, strung between poles like a telephone line >>>>

    With the feed point in the middle, not at one end.

    The bastard - my dad never told me that when I was a teenager.

    This would be silly. To work well it would need to be so far above the >ground that it'd be ridiculously impractical.

    Do what everyone else does and use the earth as one half and a wire as
    the other half. Or use a vertical loop aerial with one side aimed at the >transmitter so the direction of the signal is in the plane of the loop.

    It's academic now as I have no plans to create a similar installation.
    I ran the cable from an attic window to a tree at the bottom of the
    garden. Does this mean I should have installed an earth spike at the
    far end? Too late now.
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From liz@liz@poppyrecords.invalid.invalid (Liz Tuddenham) to uk.telecom on Sun Oct 18 17:51:10 2026
    From Newsgroup: uk.telecom

    The Natural Philosopher <tnp@invalid.invalid> wrote:

    On 16/10/2026 13:03, Scott wrote:
    As it happens, it is a FRITZ!Box and Zen is my ISP. Does this mean I
    can plug it into a LAN port (not FON) and will it work out of the box?
    Does SIP phone require a power supply?

    The Fritzbox should have enough power to drive a basic analogue phone

    If each 'phone had a REN of 1, it should drive 4 of them, otherwise it
    is not properly compatible.
    --
    ~ Liz Tuddenham ~
    (Remove the ".invalid"s and add ".co.uk" to reply)
    www.poppyrecords.co.uk
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From liz@liz@poppyrecords.invalid.invalid (Liz Tuddenham) to uk.telecom on Sun Oct 18 18:11:44 2026
    From Newsgroup: uk.telecom

    Scott <newsgroups@gefion.myzen.co.uk> wrote:

    [...]
    ...Reception of 648 kHz is not great in Glasgow. Should the aerial
    be half the wavelength: 232 metres? Vertical or horizontal :-)

    The usual limitation on Medium Wave reception is likely to be local interference, rather then actual low signal level. Loop aerials or
    ferrite rod aerials can do a lot to improve the signal-to-noise ratio if
    the receiver has sufficient sensitivity.

    If the receiver has a ferrite rod aerial but is not sensitive enough, a large-area loop can be made by winding a few turns of insulated wire
    around a big cardboard box, tuning it with a variable capacitor and
    standing the receiver inside it.(obviously with one end of the box open,
    so you can still hear the radio).
    --
    ~ Liz Tuddenham ~
    (Remove the ".invalid"s and add ".co.uk" to reply)
    www.poppyrecords.co.uk
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From liz@liz@poppyrecords.invalid.invalid (Liz Tuddenham) to uk.telecom on Sun Oct 18 18:22:13 2026
    From Newsgroup: uk.telecom

    Scott <newsgroups@gefion.myzen.co.uk> wrote:

    On Sun, 18 Oct 2026 14:23:47 +0100, Brian Gregory <void-invalid-dead-dontuse@email.invalid> wrote:

    On 18/10/2026 10:21, Scott wrote:
    On Sun, 18 Oct 2026 03:43:32 +0100, "J. P. Gilliver"
    <G6JPG@255soft.uk> wrote:

    On 2026/10/17 11:50:50, The Natural Philosopher wrote:
    On 17/10/2026 10:28, Scott wrote:
    On Sat, 17 Oct 2026 08:47:20 +0100, The Natural Philosopher
    <tnp@invalid.invalid> wrote:

    So mobile is like VOIP is a completely false statement, Qualitry IS >>>>>> NOTHING like VOIP. Its like comparing Radio Caroline on the MW with a >>>>>> full power VHF radio signal

    True. Reception of 648 kHz is not great in Glasgow. Should the aerial >>>>> be half the wavelength: 232 metres? Vertical or horizontal :-)

    Seriously yes. Horizontally, strung between poles like a telephone line >>>>

    With the feed point in the middle, not at one end.

    The bastard - my dad never told me that when I was a teenager.

    This would be silly. To work well it would need to be so far above the >ground that it'd be ridiculously impractical.

    Do what everyone else does and use the earth as one half and a wire as
    the other half. Or use a vertical loop aerial with one side aimed at the >transmitter so the direction of the signal is in the plane of the loop.

    It's academic now as I have no plans to create a similar installation.
    I ran the cable from an attic window to a tree at the bottom of the
    garden. Does this mean I should have installed an earth spike at the
    far end? Too late now.

    It depend on whether you were listening in the tree or the attic. The
    receiver needs to be connected between the aerial and earth.
    --
    ~ Liz Tuddenham ~
    (Remove the ".invalid"s and add ".co.uk" to reply)
    www.poppyrecords.co.uk
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Scott@newsgroups@gefion.myzen.co.uk to uk.telecom on Sun Oct 18 20:47:58 2026
    From Newsgroup: uk.telecom

    On Sun, 18 Oct 2026 18:22:13 +0100, liz@poppyrecords.invalid.invalid
    (Liz Tuddenham) wrote:

    Scott <newsgroups@gefion.myzen.co.uk> wrote:

    On Sun, 18 Oct 2026 14:23:47 +0100, Brian Gregory
    <void-invalid-dead-dontuse@email.invalid> wrote:

    On 18/10/2026 10:21, Scott wrote:
    On Sun, 18 Oct 2026 03:43:32 +0100, "J. P. Gilliver"
    <G6JPG@255soft.uk> wrote:

    On 2026/10/17 11:50:50, The Natural Philosopher wrote:
    On 17/10/2026 10:28, Scott wrote:
    On Sat, 17 Oct 2026 08:47:20 +0100, The Natural Philosopher
    <tnp@invalid.invalid> wrote:

    So mobile is like VOIP is a completely false statement, Qualitry IS >> >>>>>> NOTHING like VOIP. Its like comparing Radio Caroline on the MW with a >> >>>>>> full power VHF radio signal

    True. Reception of 648 kHz is not great in Glasgow. Should the aerial >> >>>>> be half the wavelength: 232 metres? Vertical or horizontal :-)

    Seriously yes. Horizontally, strung between poles like a telephone line >> >>>>

    With the feed point in the middle, not at one end.

    The bastard - my dad never told me that when I was a teenager.

    This would be silly. To work well it would need to be so far above the
    ground that it'd be ridiculously impractical.

    Do what everyone else does and use the earth as one half and a wire as
    the other half. Or use a vertical loop aerial with one side aimed at the
    transmitter so the direction of the signal is in the plane of the loop.

    It's academic now as I have no plans to create a similar installation.
    I ran the cable from an attic window to a tree at the bottom of the
    garden. Does this mean I should have installed an earth spike at the
    far end? Too late now.

    It depend on whether you were listening in the tree or the attic. The >receiver needs to be connected between the aerial and earth.

    It's all coming back to me now. The radio had an earth point which my
    dad told me to connect to the central heating. Was this right enough?
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From liz@liz@poppyrecords.invalid.invalid (Liz Tuddenham) to uk.telecom on Sun Oct 18 21:35:40 2026
    From Newsgroup: uk.telecom

    Scott <newsgroups@gefion.myzen.co.uk> wrote:

    On Sun, 18 Oct 2026 18:22:13 +0100, liz@poppyrecords.invalid.invalid
    (Liz Tuddenham) wrote:

    Scott <newsgroups@gefion.myzen.co.uk> wrote:

    On Sun, 18 Oct 2026 14:23:47 +0100, Brian Gregory
    <void-invalid-dead-dontuse@email.invalid> wrote:

    On 18/10/2026 10:21, Scott wrote: > On Sun, 18 Oct 2026 03:43:32
    +0100, "J. P. Gilliver" > <G6JPG@255soft.uk> wrote: > >> On 2026/10/17
    11:50:50, The Natural Philosopher wrote: >>> On 17/10/2026 10:28,
    Scott wrote: >>>> On Sat, 17 Oct 2026 08:47:20 +0100, The Natural
    Philosopher >>>> <tnp@invalid.invalid> wrote: >>> >>>>> So mobile is
    like VOIP is a completely false statement, Qualitry IS >>>>> NOTHING
    like VOIP. Its like comparing Radio Caroline on the MW with a >>>>>
    full power VHF radio signal >>>> >>>> True. Reception of 648 kHz is
    not great in Glasgow. Should the aerial >>>> be half the wavelength:
    232 metres? Vertical or horizontal :-) >>> >>> Seriously yes.
    Horizontally, strung between poles like a telephone line >>> >>> >>
    With the feed point in the middle, not at one end. > > The bastard -
    my dad never told me that when I was a teenager.

    This would be silly. To work well it would need to be so far above the
    ground that it'd be ridiculously impractical.

    Do what everyone else does and use the earth as one half and a wire as
    the other half. Or use a vertical loop aerial with one side aimed at
    the transmitter so the direction of the signal is in the plane of the
    loop.

    It's academic now as I have no plans to create a similar installation.
    I ran the cable from an attic window to a tree at the bottom of the
    garden. Does this mean I should have installed an earth spike at the
    far end? Too late now.

    It depend on whether you were listening in the tree or the attic. The >receiver needs to be connected between the aerial and earth.

    It's all coming back to me now. The radio had an earth point which my
    dad told me to connect to the central heating. Was this right enough?

    That would have been good enough for most major Medium Wave and Long
    wave radio stations as it would eventually lead to earth through the
    house pipework and the incoming water main. Nowadays, with
    switched-mode power supplies putting hash on the water pipes through the mandatory earth bonding straps and the probablilty that the water main
    has been replaced by plastic, it is just as likely to increase the
    interference more than the wanted signal.
    --
    ~ Liz Tuddenham ~
    (Remove the ".invalid"s and add ".co.uk" to reply)
    www.poppyrecords.co.uk
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Brian Gregory@void-invalid-dead-dontuse@email.invalid to uk.telecom on Sun Oct 18 21:52:47 2026
    From Newsgroup: uk.telecom

    On 16/10/2026 19:34, Marco Moock wrote:
    They do that and most users use such a service. Direct VOIP calling is possible, but no normal users uses that. There was an idea to use DNS to
    get the remote's IP, but the telephone companies didn't like that.

    Direct calling by IP address would be a security nightmare.
    --
    Brian Gregory (in England).
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Brian Gregory@void-invalid-dead-dontuse@email.invalid to uk.telecom on Sun Oct 18 21:58:34 2026
    From Newsgroup: uk.telecom

    On 17/10/2026 12:15, Chris Green wrote:
    Richmond <dnomhcir@gmx.com> wrote:
    Brian Gregory <void-invalid-dead-dontuse@email.invalid> writes:

    However if you want to use a VoIP phone instead of an ISP provided ATA
    you'll need to find out the required settings for the phone and also
    how to disable the ATA in the router and configure it to pass the VoIP
    through to your VoIP phone.

    Presumably you could have a different number on the VOIP phone, and the
    router should route calls to the appropriate port, phone port 1 or 2, or
    the Ethernet port.

    If it's a VOIP phone then the router isn't involved at all except to the extent of sending and receiving the VOIP data packets.


    Or if all phones had the same number, then the router would route
    traffic to the one which made the call.

    See above, the router isn't involved. This is one of the difficulties
    when using VOIP phones via a typical home router that does NAT. There
    isn't a simple way for the packets of data coming 'back' to find the VOIP handset. The A&A website has a better explanation of this problem than I will ever manage, and A&A dislike NAT for this very reason.


    What would happen for incoming calls? Would all the phones rings?

    If there's more than one VOIP phone registered to a VOIP number then all
    of them will ring (or receive the call anyway). They don't have to be connected via the same router or even be in the same country. I have a
    VOIP phone on my boat in France which receives calls at the same time as
    our VOIP phones at home in the UK as it's registered with the same number
    at the same VOIP provider.


    Um. Don't forget that he wants to use his Fritz!fon, or whatever it's
    called, with the new VoIP phone and presumably to have them work like extensions on the same line did with analogue phones.
    --
    Brian Gregory (in England).
    --- Synchronet 3.22a-Linux NewsLink 1.2