There are series of programmes tonight for the anniversary of the start
of broadcasts from Alexandra Palace.
Starts with
DOCUMENTARY: Television's Opening Night: How the Box Was Born
On: BBC Four
Date: Wednesday 4th November 2026 (starting in 3 hours and 4 minutes)
Time: 21:00 to 22:30 (1 hour and 30 minutes long)
Dallas Campbell, Professor Danielle George and Dr Hugh Hunt mark the
80th anniversary of Britain's very first TV broadcast by trying to
recreate the landmark event. The inaugural programme came live from Alexandria Palace on November 2, 1936, but there are no surviving
recordings of the show. In response, the presenter trio set out to
recreate every aspect of this first broadcast, from the variety acts featured right down to the camera equipment used, using authentic
technology and filming techniques. Plus, pioneering TV engineer John
On 2026/11/4 17:59:31, JMB99 wrote:
There are series of programmes tonight for the anniversary of the start
of broadcasts from Alexandra Palace.
Starts with
DOCUMENTARY: Television's Opening Night: How the Box Was Born
On: BBC Four
Date: Wednesday 4th November 2026 (starting in 3 hours and 4 minutes)
Time: 21:00 to 22:30 (1 hour and 30 minutes long)
Dallas Campbell, Professor Danielle George and Dr Hugh Hunt mark the
80th anniversary of Britain's very first TV broadcast by trying to
recreate the landmark event. The inaugural programme came live from
Alexandria Palace on November 2, 1936, but there are no surviving
recordings of the show. In response, the presenter trio set out to
recreate every aspect of this first broadcast, from the variety acts
featured right down to the camera equipment used, using authentic
technology and filming techniques. Plus, pioneering TV engineer John
I hadn't realised they'd changed the scanning to horizontal by this
stage. I suppose, if receivers had to be switchable, that was much easier.
[]
I have always thought the mechanical system got a bad deal, in that - in those days when every active device (valve, or at best envelopes with
rwo devices in, or three if one was e. g. a diode) cost a significant
amount, the mechanical _receivers_ were surely cheaper? (Not
dual-standard sets, which obviously had to be electronic anyway.) Or
were no 240-line mechanical receivers made? If that is the case,
presumably there was at least some distortion, as the mechanical scanner would involve at least slightly curved lines, whereas I can't imagine an electronic receiver doing so (intentionally, anyway!).
I always thought that it must have been obvious that the Baird system
was hopeless, as it was completely unscaleable to higher resolutions or
to broader broadcasting needs.-a It was suitable only for studio
broadcasts of a single talking head, and the conditions for that person seemed, from this programme, to be pretty uncomfortable.-a For outside broadcasts the scanning beam was simply unusable with no technical
solution that anyone could devise.-a I expect that Heath Robinson was jealous that Logie Baird got there first.
I assume that this must have been evident in 1936 to all of those
involved, except perhaps Baird himself and any others that he managed to brainwash, and that the BBC went through the charade of a comparison
between systems only because they needed to have a public demonstration
that the electronic system was vastly superior in all respects.
On 08/11/2026 11:14, Clive Page wrote:
I always thought that it must have been obvious that the Baird system
was hopeless, as it was completely unscaleable to higher resolutions
or to broader broadcasting needs.-a It was suitable only for studio
broadcasts of a single talking head, and the conditions for that
person seemed, from this programme, to be pretty uncomfortable.-a For
outside broadcasts the scanning beam was simply unusable with no
technical solution that anyone could devise.-a I expect that Heath
Robinson was jealous that Logie Baird got there first.
I assume that this must have been evident in 1936 to all of those
involved, except perhaps Baird himself and any others that he managed
to brainwash, and that the BBC went through the charade of a
comparison between systems only because they needed to have a public
demonstration that the electronic system was vastly superior in all
respects.
He was a very good publicist - I always think of him as the Clive
Sinclair of that period.-a :-)
On 08/11/2026 11:16, JMB99 wrote:
On 08/11/2026 11:14, Clive Page wrote:
I always thought that it must have been obvious that the Baird system
was hopeless, as it was completely unscaleable to higher resolutions
or to broader broadcasting needs.-a It was suitable only for studio
broadcasts of a single talking head, and the conditions for that
person seemed, from this programme, to be pretty uncomfortable.-a For
outside broadcasts the scanning beam was simply unusable with no
technical solution that anyone could devise.-a I expect that Heath
Robinson was jealous that Logie Baird got there first.
I assume that this must have been evident in 1936 to all of those
involved, except perhaps Baird himself and any others that he managed
to brainwash, and that the BBC went through the charade of a
comparison between systems only because they needed to have a public
demonstration that the electronic system was vastly superior in all
respects.
He was a very good publicist - I always think of him as the Clive
Sinclair of that period.-a :-)
That's a good comparison.-a But to do him justice there were one or two Sinclair products that were ok-ish, for example his pocket calculator
and his wrist-watch.-a I didn't buy any but some of my friends did.
In my opinion another "scientist" of the same type, though rather
earlier, was Nicola Tesla.
On 04/11/2026 22:36, J. P. Gilliver wrote:[]
I have always thought the mechanical system got a bad deal, in that - in
those days when every active device (valve, or at best envelopes with
rwo devices in, or three if one was e. g. a diode) cost a significant
amount, the mechanical _receivers_ were surely cheaper? (Not
dual-standard sets, which obviously had to be electronic anyway.) Or
were no 240-line mechanical receivers made? If that is the case,
presumably there was at least some distortion, as the mechanical scanner
would involve at least slightly curved lines, whereas I can't imagine an
electronic receiver doing so (intentionally, anyway!).
I always thought that it must have been obvious that the Baird system
was hopeless, as it was completely unscaleable to higher resolutions or
to broader broadcasting needs. It was suitable only for studio
broadcasts of a single talking head, and the conditions for that person seemed, from this programme, to be pretty uncomfortable. For outside broadcasts the scanning beam was simply unusable with no technical
solution that anyone could devise. I expect that Heath Robinson was
jealous that Logie Baird got there first.
I assume that this must have been evident in 1936 to all of those
involved, except perhaps Baird himself and any others that he managed to brainwash, and that the BBC went through the charade of a comparison
between systems only because they needed to have a public demonstration
that the electronic system was vastly superior in all respects.
On 2026/11/8 11:14:1, Clive Page wrote:
On 04/11/2026 22:36, J. P. Gilliver wrote:[]
I have always thought the mechanical system got a bad deal, in that - in >>> those days when every active device (valve, or at best envelopes with
rwo devices in, or three if one was e. g. a diode) cost a significant
amount, the mechanical _receivers_ were surely cheaper? (Not
dual-standard sets, which obviously had to be electronic anyway.) Or
were no 240-line mechanical receivers made? If that is the case,
presumably there was at least some distortion, as the mechanical scanner >>> would involve at least slightly curved lines, whereas I can't imagine an >>> electronic receiver doing so (intentionally, anyway!).
I always thought that it must have been obvious that the Baird system
was hopeless, as it was completely unscaleable to higher resolutions or
Didn't they get to 240? (A lot of YouTube viewing is surely no better
than that, especially if not full-screen.)
to broader broadcasting needs. It was suitable only for studio
broadcasts of a single talking head, and the conditions for that person
seemed, from this programme, to be pretty uncomfortable. For outside
broadcasts the scanning beam was simply unusable with no technical
solution that anyone could devise. I expect that Heath Robinson was
jealous that Logie Baird got there first.
The scanning beam wasn't used for outside broadcasts - a mirror-drum was used, at least for the Derby. (We had some discussions here a few years
ago as to whether that was the reason an OB van is referred to as a "scanner"; many origins were suggested, but the Baird-origin one seemed
to win.)
On 08/11/2026 17:52, J. P. Gilliver wrote:[]
The scanning beam wasn't used for outside broadcasts - a mirror-drum was
used, at least for the Derby. (We had some discussions here a few years
ago as to whether that was the reason an OB van is referred to as a
"scanner"; many origins were suggested, but the Baird-origin one seemed
to win.)
I heard at the time when I followed such things that it referred to the video recorders they carried. The heads scanned the tape....
On 2026/11/8 11:14:1, Clive Page wrote:
On 04/11/2026 22:36, J. P. Gilliver wrote:[]
I have always thought the mechanical system got a bad deal, in that - in >>> those days when every active device (valve, or at best envelopes with
rwo devices in, or three if one was e. g. a diode) cost a significant
amount, the mechanical _receivers_ were surely cheaper? (Not
dual-standard sets, which obviously had to be electronic anyway.) Or
were no 240-line mechanical receivers made? If that is the case,
presumably there was at least some distortion, as the mechanical scanner >>> would involve at least slightly curved lines, whereas I can't imagine an >>> electronic receiver doing so (intentionally, anyway!).
I always thought that it must have been obvious that the Baird system
was hopeless, as it was completely unscaleable to higher resolutions or
Didn't they get to 240? (A lot of YouTube viewing is surely no better
than that, especially if not full-screen.)
to broader broadcasting needs. It was suitable only for studio
broadcasts of a single talking head, and the conditions for that person
seemed, from this programme, to be pretty uncomfortable. For outside
broadcasts the scanning beam was simply unusable with no technical
solution that anyone could devise. I expect that Heath Robinson was
jealous that Logie Baird got there first.
The scanning beam wasn't used for outside broadcasts - a mirror-drum was used, at least for the Derby. (We had some discussions here a few years
ago as to whether that was the reason an OB van is referred to as a "scanner"; many origins were suggested, but the Baird-origin one seemed
to win.)
I'm inclined to agree that it probably _was_ inferior - certainly
I assume that this must have been evident in 1936 to all of those
involved, except perhaps Baird himself and any others that he managed to
brainwash, and that the BBC went through the charade of a comparison
between systems only because they needed to have a public demonstration
that the electronic system was vastly superior in all respects.
wouldn't even consider it today, with the cheapness of modern
electronics. (Though I think there were almost some large public-display systems [sports stadia and the like] that used mirror-drum scanning,
when powerful lasers became available, but that was overtaken.) But in
the days when a single valve cost a significant number of hours' work
for the ordinary man, I presume "televisors" were far cheaper for the consumer than all-electronic sets - they only required a receiver (which all-electronic sets did too) and a motor (which technology was well-established by then); this doesn't seem to get _mentioned_ when the subject comes up = the engineers and administrators preferring to use
the system that is (definitely - I'm not arguing there) best
technically, and also easier to use, and the poor consumer can go hang.
(An attitude that has continued ever since, and still prevails - the
only exception I can think of that went too far the other way was how
long system A was kept going.)
On 08/11/2026 17:52, J. P. Gilliver wrote:
On 2026/11/8 11:14:1, Clive Page wrote:
On 04/11/2026 22:36, J. P. Gilliver wrote:[]
I have always thought the mechanical system got a bad deal, in that - in >>> those days when every active device (valve, or at best envelopes with
rwo devices in, or three if one was e. g. a diode) cost a significant
amount, the mechanical _receivers_ were surely cheaper? (Not
dual-standard sets, which obviously had to be electronic anyway.) Or
were no 240-line mechanical receivers made? If that is the case,
presumably there was at least some distortion, as the mechanical scanner >>> would involve at least slightly curved lines, whereas I can't imagine an >>> electronic receiver doing so (intentionally, anyway!).
I always thought that it must have been obvious that the Baird system
was hopeless, as it was completely unscaleable to higher resolutions or
Didn't they get to 240? (A lot of YouTube viewing is surely no better
than that, especially if not full-screen.)
to broader broadcasting needs. It was suitable only for studio
broadcasts of a single talking head, and the conditions for that person
seemed, from this programme, to be pretty uncomfortable. For outside
broadcasts the scanning beam was simply unusable with no technical
solution that anyone could devise. I expect that Heath Robinson was
jealous that Logie Baird got there first.
The scanning beam wasn't used for outside broadcasts - a mirror-drum was used, at least for the Derby. (We had some discussions here a few years
ago as to whether that was the reason an OB van is referred to as a "scanner"; many origins were suggested, but the Baird-origin one seemed
to win.)
I'm inclined to agree that it probably _was_ inferior - certainly
I assume that this must have been evident in 1936 to all of those
involved, except perhaps Baird himself and any others that he managed to >> brainwash, and that the BBC went through the charade of a comparison
between systems only because they needed to have a public demonstration
that the electronic system was vastly superior in all respects.
wouldn't even consider it today, with the cheapness of modern
electronics. (Though I think there were almost some large public-display systems [sports stadia and the like] that used mirror-drum scanning,
when powerful lasers became available, but that was overtaken.) But in
the days when a single valve cost a significant number of hours' work
for the ordinary man, I presume "televisors" were far cheaper for the consumer than all-electronic sets - they only required a receiver (which all-electronic sets did too) and a motor (which technology was well-established by then); this doesn't seem to get _mentioned_ when the subject comes up = the engineers and administrators preferring to use
the system that is (definitely - I'm not arguing there) best
technically, and also easier to use, and the poor consumer can go hang.
(An attitude that has continued ever since, and still prevails - the
only exception I can think of that went too far the other way was how
long system A was kept going.)
I find it hard to believe that all it needed as receiver was a light,
motor, and spinning disc. That would indeed have been cheaper.
But surely there's a need for line and frame synchronisation, which the electronic system supported via line and frame sync pulses. There must
have been complicated mechanisms to keep the motor in sync at least.
Maybe that could be done without expensive electronics, but I don't see how.
The disc was spun by a motor with a rheostat to set the speed slightly
faster than required, then a phonic wheel, with its electromagnet in the anode circuit of a valve in the vision channel, pulled the rotation into sync. There were no sync pulses as such, the black border of the
picture serving as a rough guide. When they 'faded' the scene, a board
with black and white squares was slid in fromt of the camera to give a
signal sufficient to maintain synchronism.
Later versions of the Baird system may have improved on this but I am
not aware of what those improvements might have been.
The blacker-than-black sync pulses were one of the innovations of
Blumlein's team, which made the EMI electronic system so much more
reliable. They chose positive modulation because they considered that
the white spots cause by motor car ignition interference would be less obtrusive than the loss of sync which the same interference would cause
if the modulation were negative. Flywheel sync came later.
Clive Page <clive.g.page@gmail.com> wrote:
On 08/11/2026 17:52, J. P. Gilliver wrote:
On 2026/11/8 11:14:1, Clive Page wrote:
On 04/11/2026 22:36, J. P. Gilliver wrote:[]
Didn't they get to 240? (A lot of YouTube viewing is surely no betterI have always thought the mechanical system got a bad deal, in that - in >>>>> those days when every active device (valve, or at best envelopes with >>>>> rwo devices in, or three if one was e. g. a diode) cost a significant >>>>> amount, the mechanical _receivers_ were surely cheaper? (Not
dual-standard sets, which obviously had to be electronic anyway.) Or >>>>> were no 240-line mechanical receivers made? If that is the case,
presumably there was at least some distortion, as the mechanical scanner >>>>> would involve at least slightly curved lines, whereas I can't imagine an >>>>> electronic receiver doing so (intentionally, anyway!).
I always thought that it must have been obvious that the Baird system
was hopeless, as it was completely unscaleable to higher resolutions or >>>
than that, especially if not full-screen.)
to broader broadcasting needs. It was suitable only for studio
broadcasts of a single talking head, and the conditions for that person >>>> seemed, from this programme, to be pretty uncomfortable. For outside
broadcasts the scanning beam was simply unusable with no technical
solution that anyone could devise. I expect that Heath Robinson was
jealous that Logie Baird got there first.
The scanning beam wasn't used for outside broadcasts - a mirror-drum was >>> used, at least for the Derby. (We had some discussions here a few years
ago as to whether that was the reason an OB van is referred to as a
"scanner"; many origins were suggested, but the Baird-origin one seemed
to win.)
I'm inclined to agree that it probably _was_ inferior - certainly
I assume that this must have been evident in 1936 to all of those
involved, except perhaps Baird himself and any others that he managed to >>>> brainwash, and that the BBC went through the charade of a comparison
between systems only because they needed to have a public demonstration >>>> that the electronic system was vastly superior in all respects.
wouldn't even consider it today, with the cheapness of modern
electronics. (Though I think there were almost some large public-display >>> systems [sports stadia and the like] that used mirror-drum scanning,
when powerful lasers became available, but that was overtaken.) But in
the days when a single valve cost a significant number of hours' work
for the ordinary man, I presume "televisors" were far cheaper for the
consumer than all-electronic sets - they only required a receiver (which >>> all-electronic sets did too) and a motor (which technology was
well-established by then); this doesn't seem to get _mentioned_ when the >>> subject comes up = the engineers and administrators preferring to use
the system that is (definitely - I'm not arguing there) best
technically, and also easier to use, and the poor consumer can go hang.
(An attitude that has continued ever since, and still prevails - the
only exception I can think of that went too far the other way was how
long system A was kept going.)
I find it hard to believe that all it needed as receiver was a light,
motor, and spinning disc. That would indeed have been cheaper.
But surely there's a need for line and frame synchronisation, which the
electronic system supported via line and frame sync pulses. There must
have been complicated mechanisms to keep the motor in sync at least.
Maybe that could be done without expensive electronics, but I don't see how.
The disc was spun by a motor with a rheostat to set the speed slightly
faster than required, then a phonic wheel, with its electromagnet in the anode circuit of a valve in the vision channel, pulled the rotation into sync. There were no sync pulses as such, the black border of the
picture serving as a rough guide. When they 'faded' the scene, a board
with black and white squares was slid in fromt of the camera to give a
signal sufficient to maintain synchronism.
Later versions of the Baird system may have improved on this but I am
not aware of what those improvements might have been.
The blacker-than-black sync pulses were one of the innovations of
Blumlein's team, which made the EMI electronic system so much more
reliable. They chose positive modulation because they considered that
the white spots cause by motor car ignition interference would be less obtrusive than the loss of sync which the same interference would cause
if the modulation were negative. Flywheel sync came later.
On 2026/11/10 16:8:46, Liz Tuddenham wrote:
[]
The disc was spun by a motor with a rheostat to set the speed slightly faster than required, then a phonic wheel, with its electromagnet in the anode circuit of a valve in the vision channel, pulled the rotation into sync. There were no sync pulses as such, the black border of the
picture serving as a rough guide. When they 'faded' the scene, a board with black and white squares was slid in fromt of the camera to give a signal sufficient to maintain synchronism.
So am I right - a televisor was a lot cheaper than an all-electronic set?
Later versions of the Baird system may have improved on this but I am
not aware of what those improvements might have been.
The blacker-than-black sync pulses were one of the innovations of Blumlein's team, which made the EMI electronic system so much more reliable. They chose positive modulation because they considered that
the white spots cause by motor car ignition interference would be less obtrusive than the loss of sync which the same interference would cause
if the modulation were negative. Flywheel sync came later.
Ah, that makes sense! I always assumed system A used positive modulation since that just seemed the obvious way to do it (brighter picture ->
more transmiiter power), and that turning ignition spots black was a
clever idea; it never occurred to me that the matter had been considered
and the choice made for that reason.
Though thinking about it now, they could always have inverted the video
but not the sync pulses (thus making them "whiter-than-white")!
J. P. Gilliver <G6JPG@255soft.uk> wrote:[]
[]So am I right - a televisor was a lot cheaper than an all-electronic set?
Though thinking about it now, they could always have inverted the video
but not the sync pulses (thus making them "whiter-than-white")!
They could - but a super-bright white margin on the picture would be
more disturbing than a black one and the effect of a 'rolling' picture, through loss of frame lock, would have been horrendous.
On 2026/11/11 12:39:36, Liz Tuddenham wrote:
J. P. Gilliver <G6JPG@255soft.uk> wrote:[]
You're right about the rolling. When locked, though, it wouldn't haveSo am I right - a televisor was a lot cheaper than an all-electronic set? >[]
Though thinking about it now, they could always have inverted the video
but not the sync pulses (thus making them "whiter-than-white")!
They could - but a super-bright white margin on the picture would be
more disturbing than a black one and the effect of a 'rolling' picture,
through loss of frame lock, would have been horrendous.
been a problem in practice, because every CRT set I ever saw - even into
the days of FSTs (tubes with square corners) - was set to overscan,
often to a ridiculous extent.
| Sysop: | Amessyroom |
|---|---|
| Location: | Fayetteville, NC |
| Users: | 76 |
| Nodes: | 6 (0 / 6) |
| Uptime: | 54:48:34 |
| Calls: | 1,265 |
| Calls today: | 1 |
| Files: | 1,362 |
| D/L today: |
3 files (2,684K bytes) |
| Messages: | 285,582 |