• TV/Radio aerial signal power levels: simple explanation needed.

    From David Paste@pastedavid@gmail.com to uk.tech.broadcast on Fri Oct 16 13:22:44 2026
    From Newsgroup: uk.tech.broadcast

    Hello,

    Can anyone explain to me like IrCOm an idiot, because IrCOm an idiot, about the signal power levels at the receiver end of a piece of coax?

    (IrCOve posted this in uk.tech.broadcast and uk.d-i-y)

    BACKGROUND

    Classic FM, for example, broadcasts from Holme Moss on 101.1 MHz with an output of 250 kW (which I assume is ERP, which I sort of understand as
    the power focussed in particular direction by itrCOs transmitting antenna
    in the same way light can be focussed by glass lenses).

    There is attenuation as the signal travels to me (50.31 km away as the
    crow flies), and this attenuation follows an inverse square law, so 1/2
    531 096 100

    so:
    250 000 000 / 2 531 096 100
    which equals
    0.0987714374

    I assume this is in watts?

    And this is the signal strength in free air at the position of my aerial
    (half wave dipole).

    Then there is about 20 metres of coax, which I believe is RG-11, which according to a datasheet I found on the RS website has an attenuation of
    74.8 dB per 100 metres at 700 MHz.

    I do not know how to work out the power loss through that 20 metres of
    coax as I do not really understand dB, other than rCLitrCOs a comparative level of powerrCY. IrCOve no idea what that means.

    My radio (which is in the cellar, hence the need for an external aerial)
    has the following details in the manual:

    Sensitivity = 2.5 -|V (IHF) (what is IHF?)

    S/N 26 dB 2.2 -|V

    So it needs microvolts but how is this figure related to the watts from
    the transmitter? Do I need to know the current in the coax?

    How is the signal strength measured? Does it need a special meter, or
    can a multimeter be used?

    My radio doesnrCOt always get a good signal; in some weathers there is a background hiss. I would like to get rid of this. I suppose an amplifier
    at the aerial itself would be needed?

    Thanks in advance for any help, and apologies for the lengthy question.

    D.P.
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From J. P. Gilliver@G6JPG@255soft.uk to uk.tech.broadcast on Fri Oct 16 14:08:07 2026
    From Newsgroup: uk.tech.broadcast

    On 2026/10/16 13:22:44, David Paste wrote:
    Hello,

    Can anyone explain to me like IrCOm an idiot, because IrCOm an idiot, about the signal power levels at the receiver end of a piece of coax?

    (IrCOve posted this in uk.tech.broadcast and uk.d-i-y)

    BACKGROUND

    Classic FM, for example, broadcasts from Holme Moss on 101.1 MHz with an output of 250 kW (which I assume is ERP, which I sort of understand as
    the power focussed in particular direction by itrCOs transmitting antenna
    in the same way light can be focussed by glass lenses).

    Yes - Effective Radiated Power; you'd need to check the source you got
    the 250 kW figure from, but usually, yes, people often publish their transmitter power in ERP rather than what goes up the feed, since it
    makes for a bigger figure. Of course, TANSTAAFL - it's the gain of the transmitting aerial, which means more power in the wanted direction, but
    less in others.


    There is attenuation as the signal travels to me (50.31 km away as the
    crow flies), and this attenuation follows an inverse square law, so 1/2
    531 096 100

    I don't quite understand your figures.


    so:
    250 000 000 / 2 531 096 100
    which equals
    0.0987714374

    I assume this is in watts?

    If you started with watts, then yes.


    And this is the signal strength in free air at the position of my aerial (half wave dipole).

    Could be the theoretical isotropic aerial (same in all directions of a
    sphere), but as such things don't actually exist, the half-wave dipole
    is often used (if you see "dBd" or "dBi" that means "dB relative to a dipole/isotropic aerial"). IIRR, the difference isn't great.


    Then there is about 20 metres of coax, which I believe is RG-11, which according to a datasheet I found on the RS website has an attenuation of 74.8 dB per 100 metres at 700 MHz.

    Probably a lot less if you're talking about Classic FM's ordinary band
    II signal, which will be somewhere around 100 MHz. (You mention hiss, so
    I assume you're talking normal analogue FM reception.)


    I do not know how to work out the power loss through that 20 metres of
    coax as I do not really understand dB, other than rCLitrCOs a comparative level of powerrCY. IrCOve no idea what that means.

    They're basically logarithmic (to base 10, not e); a loss of 10 dB means one-tenth the power, 20 dB one hundredth, and so on. It's convenient as
    you just add the gains (or losses), rather than having to multiply.

    The basic unit is really the bel, but for some reason - probably because
    gains and losses are usually a lot less than 10 - we use the dB. A
    doubling or halfing is about 3 dB; if you ask your calculator what the
    log (to base 10) of 2 is, you'll see it's about 0.3, so 3 dB.

    (If a signal has been reduced by 80 dB, just remember it's had 8 bels
    knocked out of it!)


    My radio (which is in the cellar, hence the need for an external aerial)
    has the following details in the manual:

    Sensitivity = 2.5 -|V (IHF) (what is IHF?)

    (Sorry, don't know THF!)


    S/N 26 dB 2.2 -|V

    So it needs microvolts but how is this figure related to the watts from
    the transmitter? Do I need to know the current in the coax?

    If you know the nominal impedance of the input, and it is correctly
    matched to the cable and aerial used. you can work it out; a normal open
    dipole - and a lot of coax. cables - is around 70 to 75 ohms; a folded
    dipole (where the ends are joined, often done by using wide ribbon
    tape-like strip) is about 300. Adding extra elements to the dipole
    (reflector and directors) lowers this; common TV aerials tend to use a
    folded (closed loop) dipole with enough extra aerials to bring it back
    to the 7x ohms, so it matches common cable.

    26 dB S/N at 2.2 -|V means the noise in the receiver will be 26 dB (i. e.
    about 1/400) below the strength of the signal if the signal is 2.2 -|V.


    How is the signal strength measured? Does it need a special meter, or
    can a multimeter be used?

    The diodes in a normal multimeter on the AC range are probably going to
    be fine for mains frequency (50 or 60 hertz), since that's what they're designed for, but not for much above low audio frequencies. So yes, you
    do need something with higher frequency range. (Most multimeters won't
    really measure microvolts very well anyway.)


    My radio doesnrCOt always get a good signal; in some weathers there is a background hiss. I would like to get rid of this. I suppose an amplifier
    at the aerial itself would be needed?

    Well, the further up the cable the amplifier is, the better - at the
    actual aerial is best, but that puts the amplifier most at the mercy of weather; inside the loft is still better than at the receiver end. Think
    of it this way: the input stage - of the amplifier or your receiver -
    will have a noise threshold (noise generated by the stage itself) of
    some level; you want the signal to be some way above that level. If the amplifier is _before_ the cable loss, or some of it, it can boost the
    signal above the noise better. (I've not put that too well - ask and
    I'll try to improve if you don't get it.)
    there's also the matter of effective temperature of the amplifier, but
    I'll leave that for another go (for now, just: the lower the better;
    don't consider amplifiers where the manufacturer doesn't _specify_ the temperature figure).


    Thanks in advance for any help, and apologies for the lengthy question.

    Not at all: if you don't ask, you never get an answer! Hope mine are
    useful and correct; it's decades since I was actually doing this stuff!


    D.P.
    --
    J. P. Gilliver. UMRA: 1960/<1985 MB++G()ALIS-Ch++(p)Ar++T+H+Sh0!:`)DNAf

    As my chronological age races on, my OldTimers Disease now includes
    Toelio, Kneesles and SmallCox. - Chris Schram in e-s.talk, 2026-6-27
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Spike@aero.spike@mail.com to uk.tech.broadcast on Sat Oct 17 14:16:47 2026
    From Newsgroup: uk.tech.broadcast

    David Paste <pastedavid@gmail.com> wrote:
    Hello,

    Can anyone explain to me like IrCOm an idiot, because IrCOm an idiot, about the signal power levels at the receiver end of a piece of coax?

    (IrCOve posted this in uk.tech.broadcast and uk.d-i-y)

    BACKGROUND

    Classic FM, for example, broadcasts from Holme Moss on 101.1 MHz with an output of 250 kW (which I assume is ERP, which I sort of understand as
    the power focussed in particular direction by itrCOs transmitting antenna
    in the same way light can be focussed by glass lenses).

    There is attenuation as the signal travels to me (50.31 km away as the
    crow flies), and this attenuation follows an inverse square law, so 1/2
    531 096 100

    so:
    250 000 000 / 2 531 096 100
    which equals
    0.0987714374

    I assume this is in watts?

    And this is the signal strength in free air at the position of my aerial (half wave dipole).

    Then there is about 20 metres of coax, which I believe is RG-11, which according to a datasheet I found on the RS website has an attenuation of 74.8 dB per 100 metres at 700 MHz.

    I do not know how to work out the power loss through that 20 metres of
    coax as I do not really understand dB, other than rCLitrCOs a comparative level of powerrCY. IrCOve no idea what that means.

    My radio (which is in the cellar, hence the need for an external aerial)
    has the following details in the manual:

    Sensitivity = 2.5 -|V (IHF) (what is IHF?)

    S/N 26 dB 2.2 -|V

    So it needs microvolts but how is this figure related to the watts from
    the transmitter? Do I need to know the current in the coax?

    How is the signal strength measured? Does it need a special meter, or
    can a multimeter be used?

    My radio doesnrCOt always get a good signal; in some weathers there is a background hiss. I would like to get rid of this. I suppose an amplifier
    at the aerial itself would be needed?

    Thanks in advance for any help, and apologies for the lengthy question.

    D.P.

    If you get background hiss on the FM station of interest when using your dipole, first check that it is oriented correctly for the station of
    interest - the element should be at right angles to the line between you
    and the transmitter.

    Presumably this is a pole-mounted external aerial. How long has it been in place?

    ItrCOs possible that your coax feeder and/or termination at the dipole end
    has corroded or is waterlogged or suffering some form of wind damage, not
    an uncommon condition for aerials that have been in place for a few years.
    Has the quality of the signal received deteriorated over time?

    Can you receive the station of interest on a portable receiver having a
    whip aerial? If so, is it noticeably noisier than the main setup? You will probably need to move the radio about to get the best signal.
    --
    Spike
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From J. P. Gilliver@G6JPG@255soft.uk to uk.tech.broadcast on Sun Oct 18 03:39:19 2026
    From Newsgroup: uk.tech.broadcast

    On 2026/10/17 15:16:47, Spike wrote:
    David Paste <pastedavid@gmail.com> wrote:
    []
    My radio doesnrCOt always get a good signal; in some weathers there is a
    background hiss. I would like to get rid of this. I suppose an amplifier
    at the aerial itself would be needed?
    []
    If you get background hiss on the FM station of interest when using your dipole, first check that it is oriented correctly for the station of
    interest - the element should be at right angles to the line between you
    and the transmitter.

    And should be oriented at the same polarisation as the transmitter:
    you'd have to ask them, or look online, or go look at the tramsmitter
    mast. Stations intended for serious home users with home aerials _useD_
    to tend to use horizontal polarisation, those wanting users in cars
    _used_ to use vertical, and those wanting both wither slant or circular.


    Presumably this is a pole-mounted external aerial. How long has it been in place?

    ItrCOs possible that your coax feeder and/or termination at the dipole end has corroded or is waterlogged or suffering some form of wind damage, not
    an uncommon condition for aerials that have been in place for a few years. Has the quality of the signal received deteriorated over time?

    Can you receive the station of interest on a portable receiver having a
    whip aerial? If so, is it noticeably noisier than the main setup? You will probably need to move the radio about to get the best signal.


    And vary the polarisation of its aerial to find what the sender is using
    (do this outside to avoid bouncing round inside which _can_ change it a
    bit).
    --
    J. P. Gilliver. UMRA: 1960/<1985 MB++G()ALIS-Ch++(p)Ar++T+H+Sh0!:`)DNAf

    People worry that computers will get too smart and take over the world,
    but the real problem is that they're too stupid and they've already
    taken over the world (Pedro Domingos, quoted by Wolf K in
    alt.windows7.general 2018-12-10)
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From tony sayer@tony@bancom.co.uk to uk.tech.broadcast on Sun Oct 18 20:57:25 2026
    From Newsgroup: uk.tech.broadcast

    In article <11b1bgo$pici$1@dont-email.me>, J. P. Gilliver
    <G6JPG@255soft.uk> scribeth thus
    On 2026/10/17 15:16:47, Spike wrote:
    David Paste <pastedavid@gmail.com> wrote:
    []
    My radio doesnrCOt always get a good signal; in some weathers there is a >>> background hiss. I would like to get rid of this. I suppose an amplifier >>> at the aerial itself would be needed?
    []
    If you get background hiss on the FM station of interest when using your
    dipole, first check that it is oriented correctly for the station of
    interest - the element should be at right angles to the line between you
    and the transmitter.

    And should be oriented at the same polarisation as the transmitter:
    you'd have to ask them, or look online, or go look at the tramsmitter
    mast. Stations intended for serious home users with home aerials _useD_
    to tend to use horizontal polarisation, those wanting users in cars
    _used_ to use vertical, and those wanting both wither slant or circular.


    Presumably this is a pole-mounted external aerial. How long has it been in >> place?

    ItrCOs possible that your coax feeder and/or termination at the dipole end >> has corroded or is waterlogged or suffering some form of wind damage, not
    an uncommon condition for aerials that have been in place for a few years. >> Has the quality of the signal received deteriorated over time?

    Can you receive the station of interest on a portable receiver having a
    whip aerial? If so, is it noticeably noisier than the main setup? You will >> probably need to move the radio about to get the best signal.


    And vary the polarisation of its aerial to find what the sender is using
    (do this outside to avoid bouncing round inside which _can_ change it a
    bit).

    Which is a good aspect of mixed polarisation as if it does get bounced
    around the polarisation changes so what was Vert is mow Horiz and vice
    versa..

    If you get the chance drive around an urban area with a battery powered spectrum analyser the stations that used mixed are far more smoother in
    level..
    --
    Tony Sayer


    Man is least himself when he talks in his own person.

    Give him a keyboard, and he will reveal himself.


    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From David Paste@pastedavid@gmail.com to uk.tech.broadcast on Tue Oct 20 16:18:25 2026
    From Newsgroup: uk.tech.broadcast

    On 16/10/2026 14:08, J. P. Gilliver wrote:

    Yes - Effective Radiated Power; you'd need to check the source you got
    the 250 kW figure from

    Wikipedia, the page for Holme Moss Tx.


    Of course, TANSTAAFL

    IrCOm sorry, I donrCOt know what that means!


    I don't quite understand your figures.

    ItrCOs supposed to be one over 50.31 km squared, with 50310 squared being 2,531,096,100


    If you started with watts, then yes.

    Just out of interest, would this be said rCL9.8 centiwattsrCY or rCL98 milliwattsrCY? Does centi get used anywhere other than Helix shatterproof rulers and wine bottles?! ;)


    Could be the theoretical isotropic aerial (same in all directions of a sphere), but as such things don't actually exist, the half-wave dipole
    is often used (if you see "dBd" or "dBi" that means "dB relative to a dipole/isotropic aerial"). IIRR, the difference isn't great.

    It is tuned to 100 MHz, so two elements of 75 cm, if that makes any difference.

    Whilst I remember, do you know how big the gap between the two elements
    should be at the centre point? Mine are wire coat hangers straightened
    out with the tips bent to slot into a chocolate block connector, so they
    are only a few millimetres apart, but IrCOve no idea if that makes any difference.


    Probably a lot less if you're talking about Classic FM's ordinary band
    II signal, which will be somewhere around 100 MHz. (You mention hiss, so
    I assume you're talking normal analogue FM reception.)

    Yes, you are correct. I found the left over reel and it is:

    Webro WF100 Coaxial Cable
    Attenuation (d/B 100m @ 20-#C) 100MHz <6.50

    (from the data sheet at https://www.farnell.com/datasheets/2851701.pdf)


    (If a signal has been reduced by 80 dB, just remember it's had 8 bels
    knocked out of it!)

    Thanks for the explanation!


    the transmitter? Do I need to know the current in the coax?

    If you know the nominal impedance of the input, and it is correctly
    matched to the cable and aerial used.

    rCLIt uses a TV style plug, sirrCY


    (I've not put that too well - ask and I'll try to improve if you don't
    get it.)
    No, thatrCOs perfectly understandable, thanks! Like lighting an object out
    of the shadows.


    Not at all: if you don't ask, you never get an answer! Hope mine are
    useful and correct; it's decades since I was actually doing this stuff!

    I am very thankful for your kind response. I asked in another group and
    the replies were very on brand for that group :D
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From David Paste@pastedavid@gmail.com to uk.tech.broadcast on Tue Oct 20 16:23:25 2026
    From Newsgroup: uk.tech.broadcast

    On 17/10/2026 15:16, Spike wrote:

    If you get background hiss on the FM station of interest when using your dipole, first check that it is oriented correctly for the station of
    interest - the element should be at right angles to the line between you
    and the transmitter.

    Vertical.

    Presumably this is a pole-mounted external aerial. How long has it been in place?

    <snip>

    corroded or is waterlogged or suffering some form of wind damage

    <snip>

    Has the quality of the signal received deteriorated over time?


    A few years, it isn't damaged, and there's no water infiltration - one
    of the first things I checked. THEN I realised that the signal varies
    with the weather. Rainy days produce more hiss. Fine days and the signal
    (as judged by the sound of the station) is fine.

    Can you receive the station of interest on a portable receiver having a
    whip aerial? If so, is it noticeably noisier than the main setup? You will probably need to move the radio about to get the best signal.
    Yeah, but the radio is in the cellar, so I'm not expecting great
    reception down there, hence the outdoor aerial.

    Cheers!
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From John Williamson@johnwilliamson@btinternet.com to uk.tech.broadcast on Tue Oct 20 16:46:47 2026
    From Newsgroup: uk.tech.broadcast

    On 20/10/2026 16:18, David Paste wrote:
    On 16/10/2026 14:08, J. P. Gilliver wrote:

    Of course, TANSTAAFL

    IrCOm sorry, I donrCOt know what that means!

    There Ain't No Such Thing As A Free Lunch
    --
    Tciao for Now!

    John.
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Spike@aero.spike@mail.com to uk.tech.broadcast on Tue Oct 20 16:05:00 2026
    From Newsgroup: uk.tech.broadcast

    David Paste <pastedavid@gmail.com> wrote:
    On 17/10/2026 15:16, Spike wrote:

    Has the quality of the signal received deteriorated over time?

    A few years, it isn't damaged, and there's no water infiltration - one
    of the first things I checked. THEN I realised that the signal varies
    with the weather. Rainy days produce more hiss. Fine days and the signal
    (as judged by the sound of the station) is fine.

    Sounds like it might be static buildup on the antenna.

    To ensure a DC connection between all the active parts, you could try a
    1kilohm resistor connecting the two arms of the active element, which might
    be easier to do at the plug at the receiver end of the coax.
    --
    Spike
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From David Paste@pastedavid@gmail.com to uk.tech.broadcast on Tue Oct 20 17:09:58 2026
    From Newsgroup: uk.tech.broadcast

    On 20/10/2026 16:46, John Williamson wrote:
    On 20/10/2026 16:18, David Paste wrote:
    On 16/10/2026 14:08, J. P. Gilliver wrote:

    Of course, TANSTAAFL

    IrCOm sorry, I donrCOt know what that means!

    There Ain't No Such Thing As A Free Lunch


    Ah HA! Cheers!
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From David Paste@pastedavid@gmail.com to uk.tech.broadcast on Tue Oct 20 17:10:38 2026
    From Newsgroup: uk.tech.broadcast

    On 20/10/2026 17:05, Spike wrote:

    Sounds like it might be static buildup on the antenna.

    To ensure a DC connection between all the active parts, you could try a 1kilohm resistor connecting the two arms of the active element, which might be easier to do at the plug at the receiver end of the coax.


    OK, thanks!
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From J. P. Gilliver@G6JPG@255soft.uk to uk.tech.broadcast on Tue Oct 20 20:27:18 2026
    From Newsgroup: uk.tech.broadcast

    On 2026/10/20 16:18:25, David Paste wrote:
    On 16/10/2026 14:08, J. P. Gilliver wrote:
    []

    Of course, TANSTAAFL

    IrCOm sorry, I donrCOt know what that means!

    You've seen John Williamson's explanation. I _think_ the abbreviation
    was coined by Robert A. Heinlein, the science-fiction author - that's
    certainly where I came across it; but he may have been citing it from
    somewhere else.

    []

    Just out of interest, would this be said rCL9.8 centiwattsrCY or rCL98 milliwattsrCY? Does centi get used anywhere other than Helix shatterproof rulers and wine bottles?! ;)

    On the whole, the SI units work in just the powers of ten, but as you
    say, some of the older in-between ones are used in certain industries;
    as you say, the drinks industry clings on to centilitres, and I've seen hectolitres used when talking about road tankers (e. g. of fuel).
    Centimetres tend to be used for convenience in the same sort of contexts
    inches are. I've never heard anyone use centiwatts though, though it is tempting in your example, so as to give one digit before the decimal
    point! These days, people _tend_ to talk about powers in a logarithmic
    way - dBW (decibels relative to 1 watt, or dBm (1 milliwatt). And of
    course deci- - one tenth - isn't used anywhere except (those rulers!
    and) with bels. (The term - though hardly ever used! - is bel, with a
    lower case b, same as watt or joule - only capitalised in the
    abbreviations, B, W, and J.) "Decibel" is so deeply ingrained that I've
    even seen "milli-decibels", in/on the screen of a piece of test
    equipment. Oh, one other place where a non-10^3 unit is used, or at
    least was in the 1970s and may still be: on a family holiday in Italy
    then, I encountered the "etto", a unit of weight - I eventually worked
    out that it was a hectogramme, 100g, though I got the feeling it was
    used in much the same way a "quarter" is used by British sweetshops,
    with little actual memory of what it's a quarter _of_ (a pound, so four
    ounces - so the quarter and the etto are actually very close).

    []
    Whilst I remember, do you know how big the gap between the two elements should be at the centre point? Mine are wire coat hangers straightened
    out with the tips bent to slot into a chocolate block connector, so they
    are only a few millimetres apart, but IrCOve no idea if that makes any difference.

    I don't think it makes a _huge_ difference, as long as it's a relatively
    small gap compared to the wavelength being considered. Certainly, for a
    ~100 MHz (~3m) aerial, chocolate-block separation should be fine, I'd
    have thought.

    []
    Yes, you are correct. I found the left over reel and it is:

    Webro WF100 Coaxial Cable
    Attenuation (d/B 100m @ 20-#C) 100MHz <6.50

    (from the data sheet at https://www.farnell.com/datasheets/2851701.pdf)

    Says its characteristic impedance is 75 -#3 ohm, so should match an open
    dipole reasonably well.>
    (If a signal has been reduced by 80 dB, just remember it's had 8 bels
    knocked out of it!)

    Thanks for the explanation!

    Can't remember where I first came across that one, but it amused me!


    the transmitter? Do I need to know the current in the coax?

    If you know the nominal impedance of the input, and it is correctly
    matched to the cable and aerial used.

    rCLIt uses a TV style plug, sirrCY

    I'm not sure if there is an official term for those, but they're pretty universally referred to in the trade as Belling-Lee, I presume after the (one-time) largest manufacturer. (I'm not actually in the trade by the
    way!) characteristic impedance, again, seventysomething ohms.

    Not at all: if you don't ask, you never get an answer! Hope mine are
    useful and correct; it's decades since I was actually doing this stuff!

    I am very thankful for your kind response. I asked in another group and
    the replies were very on brand for that group :D

    I was hoping one of the others - much of this group _are_ in the trade
    (or were: I think mostly retired!) and know more than I ever did - would
    hop in and correct my minor errors, but maybe I haven't said anything
    glaringly wrong. (I _was_ in electronics, but mostly digital rather than analogue. I was [still am in theory] a radio amateur, but haven't done
    _that_ for decades, and when I did, mostly using pre-built equipment.)
    --
    J. P. Gilliver. UMRA: 1960/<1985 MB++G()ALIS-Ch++(p)Ar++T+H+Sh0!:`)DNAf

    The best way to achieve immortality is by not dying.
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From J. P. Gilliver@G6JPG@255soft.uk to uk.tech.broadcast on Tue Oct 20 20:32:39 2026
    From Newsgroup: uk.tech.broadcast

    On 2026/10/20 17:10:38, David Paste wrote:
    On 20/10/2026 17:05, Spike wrote:

    Sounds like it might be static buildup on the antenna.

    To ensure a DC connection between all the active parts, you could try a
    1kilohm resistor connecting the two arms of the active element, which might >> be easier to do at the plug at the receiver end of the coax.


    OK, thanks!
    Though measure across the radio input first; if the input stage of the
    radio is a transformer, it'll have a DC path anyway, unless capacitively coupled as well. (I don't know if transformer input stages - for FM
    radios - are common.)
    --
    J. P. Gilliver. UMRA: 1960/<1985 MB++G()ALIS-Ch++(p)Ar++T+H+Sh0!:`)DNAf
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Rink@rink.hof.haalditmaarweg@planet.nl to uk.tech.broadcast on Mon Nov 9 15:24:48 2026
    From Newsgroup: uk.tech.broadcast

    Op 16-10-2026 om 14:22 schreef David Paste:
    Hello,

    Can anyone explain to me like IrCOm an idiot, because IrCOm an idiot, about the signal power levels at the receiver end of a piece of coax?

    (IrCOve posted this in uk.tech.broadcast and uk.d-i-y)

    BACKGROUND

    Classic FM, for example, broadcasts from Holme Moss on 101.1 MHz with an output of 250 kW (which I assume is ERP, which I sort of understand as
    the power focussed in particular direction by itrCOs transmitting antenna
    in the same way light can be focussed by glass lenses).

    There is attenuation as the signal travels to me (50.31 km away as the
    crow flies), and this attenuation follows an inverse square law, so 1/2
    531 096 100

    so:
    250 000 000 / 2 531 096 100
    which equals
    0.0987714374

    I assume this is in watts?

    And this is the signal strength in free air at the position of my aerial (half wave dipole).

    Then there is about 20 metres of coax, which I believe is RG-11, which according to a datasheet I found on the RS website has an attenuation of 74.8 dB per 100 metres at 700 MHz.

    I do not know how to work out the power loss through that 20 metres of
    coax as I do not really understand dB, other than rCLitrCOs a comparative level of powerrCY. IrCOve no idea what that means.

    My radio (which is in the cellar, hence the need for an external aerial)
    has the following details in the manual:

    Sensitivity = 2.5 -|V (IHF) (what is IHF?)

    S/N 26 dB 2.2 -|V

    So it needs microvolts but how is this figure related to the watts from
    the transmitter? Do I need to know the current in the coax?

    How is the signal strength measured? Does it need a special meter, or
    can a multimeter be used?

    My radio doesnrCOt always get a good signal; in some weathers there is a background hiss. I would like to get rid of this. I suppose an amplifier
    at the aerial itself would be needed?

    Thanks in advance for any help, and apologies for the lengthy question.

    D.P.


    Late at the party.

    You start with 250 000 000
    That is 250 MegaWatt

    And J.P. Gilliver explained already that the signal is radiated in mixed polarization.
    The 250 kW ERP is the sum of the horizontal power and the vertical power.
    So if you only receive horizontal (or only vertical)
    you start with 125 000

    Rink
    --- Synchronet 3.22a-Linux NewsLink 1.2