• New install: Leaking water connections

    From nospam@nospam@please.invalid (AnthonyL) to uk.d-i-y on Sat Nov 14 11:32:18 2026
    From Newsgroup: uk.d-i-y

    We are having bathroom and shower rooms totally renovated. The
    installer, who seems to be very thorough, seems to tighten any
    connections, whether they be inlet or outlet, to a minimum, see where
    the leaks are after a day or two then re-tighten. The fittings are
    quality and he is relying on them being correct to create the seal.

    If I were doing them I'd be using PTFE tape or some goo or other from
    the outset.

    Just curious as to views of folk who have more experience of such
    things.
    --
    AnthonyL

    Why ever wait to finish a job before starting the next?
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Chris Green@cl@isbd.net to uk.d-i-y on Sat Nov 14 11:42:18 2026
    From Newsgroup: uk.d-i-y

    AnthonyL <nospam@please.invalid> wrote:
    We are having bathroom and shower rooms totally renovated. The
    installer, who seems to be very thorough, seems to tighten any
    connections, whether they be inlet or outlet, to a minimum, see where
    the leaks are after a day or two then re-tighten. The fittings are
    quality and he is relying on them being correct to create the seal.

    If I were doing them I'd be using PTFE tape or some goo or other from
    the outset.

    If you mean in compression fittings then they don't need PTFE tape and
    IMHO it can hinder getting a proper seal. On a clean pipe a compression fitting doesn't need to be super tight either.
    --
    Chris Green
    -+
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Brian@noinv@lid.org to uk.d-i-y on Sat Nov 14 12:00:43 2026
    From Newsgroup: uk.d-i-y

    AnthonyL <nospam@please.invalid> wrote:
    We are having bathroom and shower rooms totally renovated. The
    installer, who seems to be very thorough, seems to tighten any
    connections, whether they be inlet or outlet, to a minimum, see where
    the leaks are after a day or two then re-tighten. The fittings are
    quality and he is relying on them being correct to create the seal.

    If I were doing them I'd be using PTFE tape or some goo or other from
    the outset.

    Just curious as to views of folk who have more experience of such
    things.



    I assume these are compression fittings? If so, a bit of rCygoorCO ( proper plumbers stuff) possibly but not essential. PTFE tape, no.

    The rCyoliverCO is designed to compress onto the pipe and rCysqueezerCO into the
    fitting. The thread provides the force to compress the olive and hold it in place. Water should not get as far as the thread.

    As for retightening. I would always check after a day or so and tighten if
    any leaks spotted but I would hope / expect this to be minimal.

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From The Natural Philosopher@tnp@invalid.invalid to uk.d-i-y on Sat Nov 14 12:03:22 2026
    From Newsgroup: uk.d-i-y

    On 14/11/2026 11:32, AnthonyL wrote:
    We are having bathroom and shower rooms totally renovated. The
    installer, who seems to be very thorough, seems to tighten any
    connections, whether they be inlet or outlet, to a minimum, see where
    the leaks are after a day or two then re-tighten. The fittings are
    quality and he is relying on them being correct to create the seal.

    If I were doing them I'd be using PTFE tape or some goo or other from
    the outset.

    Just curious as to views of folk who have more experience of such
    things.


    What sort of connections? It is easy to overtighten an olive style gland... ...as well as damage any straight fibre washers, by overtightening,.

    Tape should only be used where the threads themselves supply the seal.
    Its useless with olives and flat washers and of course o-rings
    --
    Any fool can believe in principles - and most of them do!



    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From nospam@nospam@please.invalid (AnthonyL) to uk.d-i-y on Sat Nov 14 14:32:35 2026
    From Newsgroup: uk.d-i-y

    On Sat, 14 Nov 2026 12:03:22 +0000, The Natural Philosopher <tnp@invalid.invalid> wrote:

    On 14/11/2026 11:32, AnthonyL wrote:
    We are having bathroom and shower rooms totally renovated. The
    installer, who seems to be very thorough, seems to tighten any
    connections, whether they be inlet or outlet, to a minimum, see where
    the leaks are after a day or two then re-tighten. The fittings are
    quality and he is relying on them being correct to create the seal.

    If I were doing them I'd be using PTFE tape or some goo or other from
    the outset.

    Just curious as to views of folk who have more experience of such
    things.


    What sort of connections? It is easy to overtighten an olive style gland... >...as well as damage any straight fibre washers, by overtightening,.

    Tape should only be used where the threads themselves supply the seal.
    Its useless with olives and flat washers and of course o-rings


    Taps, bidet hose, basin waste. Seems as if his approach is right -
    find the minimum tightness that the connection is secure without ever overtightening.
    --
    AnthonyL

    Why ever wait to finish a job before starting the next?
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From somewhere else@"somewhere else"@gmail.com to uk.d-i-y on Sat Nov 14 17:05:31 2026
    From Newsgroup: uk.d-i-y

    AnthonyL wrote:
    We are having bathroom and shower rooms totally renovated. The
    installer, who seems to be very thorough, seems to tighten any
    connections, whether they be inlet or outlet, to a minimum, see where
    the leaks are after a day or two then re-tighten. The fittings are
    quality and he is relying on them being correct to create the seal.

    If I were doing them I'd be using PTFE tape or some goo or other from
    the outset.

    Just curious as to views of folk who have more experience of such
    things.


    PTFE tape (or hemp and paste) are only for tapered connections. I always
    use a smear of boss white on the mating face of an olive to be sure to
    be sure - the Irish approach :-)
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Roger Hayter@roger@hayter.org to uk.d-i-y on Sat Nov 14 17:15:22 2026
    From Newsgroup: uk.d-i-y

    On 14 Nov 2026 at 17:05:31 GMT+0, "Sparky" <"somewhere else"@gmail.com> wrote:

    AnthonyL wrote:
    We are having bathroom and shower rooms totally renovated. The
    installer, who seems to be very thorough, seems to tighten any
    connections, whether they be inlet or outlet, to a minimum, see where
    the leaks are after a day or two then re-tighten. The fittings are
    quality and he is relying on them being correct to create the seal.

    If I were doing them I'd be using PTFE tape or some goo or other from
    the outset.

    Just curious as to views of folk who have more experience of such
    things.


    PTFE tape (or hemp and paste) are only for tapered connections. I always
    use a smear of boss white on the mating face of an olive to be sure to
    be sure - the Irish approach :-)

    Neither hemp nor boss white are approved for potable water, though similar things are.
    --

    Roger Hayter
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From alan_m@junk@admac.myzen.co.uk to uk.d-i-y on Sat Nov 14 20:40:35 2026
    From Newsgroup: uk.d-i-y

    On 14/11/2026 11:32, AnthonyL wrote:
    We are having bathroom and shower rooms totally renovated. The
    installer, who seems to be very thorough, seems to tighten any
    connections, whether they be inlet or outlet, to a minimum, see where
    the leaks are after a day or two then re-tighten. The fittings are
    quality and he is relying on them being correct to create the seal.

    If I were doing them I'd be using PTFE tape or some goo or other from
    the outset.

    Just curious as to views of folk who have more experience of such
    things.



    No reason to use PTFE tape or "goo" on any screw on fitting in a
    bathroom. Olives and rubber or fibre washers are the seals on the
    fittings or pipe connections.
    --
    mailto : news {at} admac {dot} myzen {dot} co {dot} uk
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From John Rumm@see.my.signature@nowhere.null to uk.d-i-y on Sat Nov 14 22:17:52 2026
    From Newsgroup: uk.d-i-y

    On 14/11/2026 11:32, AnthonyL wrote:
    We are having bathroom and shower rooms totally renovated. The
    installer, who seems to be very thorough, seems to tighten any
    connections, whether they be inlet or outlet, to a minimum, see where
    the leaks are after a day or two then re-tighten. The fittings are
    quality and he is relying on them being correct to create the seal.

    If I were doing them I'd be using PTFE tape or some goo or other from
    the outset.

    Just curious as to views of folk who have more experience of such
    things.

    You must use PTFE (or equivalent) for cases where you need a seal on the threads. A common example would be the tail that screws into a radiator
    that the valve then fixes to. Getting a garden tap to screw into the
    wall mounting plate with the tap pointing down is also an art that can
    rely on copious amounts of PTFE to get the thing to lockup tight enough
    at the required angle of rotation.

    Compression joints make a proper metal to metal seal using an olive
    driven into the gap between the fitting and the pipe - the threaded part
    of the connector only provides the clamping force to squash the olive
    into shape, and hold the joint together mechanically.

    (There are some very very rare cases where a turn of PTFE under/over an
    olive can let you remake a join where there is a nick or score in the
    pipe that is preventing it from sealing normally (I recall needing to
    use this technique once only!).

    You can also use PTFE on the threads of a compression joint as a
    *lubricant* - making them easier (and quieter) to tighten in a confined
    space with short spanners etc. (Something like Jet lube V2 jointing
    compound applied to the threads would achieve the same result).

    Plastic plumbing fittings on things like sink wastes usually use a
    rubber O ring to make a seal - these need to be "tight enough" - tighter
    is no better. Things like flexi hoses that connect to modern taps also
    seal with an O ring, and the caution against much more than hand tight
    (since it would be easy to kink the flexi bit). Traditional tap
    connectors, and inlets to cisterns etc, usually use a fibre washer to
    seal. Again, tight enough is good enough.
    --
    Cheers,

    John.

    /=================================================================\
    | Internode Ltd - http://www.internode.co.uk | |-----------------------------------------------------------------|
    | John Rumm - john(at)internode(dot)co(dot)uk | \=================================================================/
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From alan_m@junk@admac.myzen.co.uk to uk.d-i-y on Sun Nov 15 10:44:24 2026
    From Newsgroup: uk.d-i-y

    On 14/11/2026 22:17, John Rumm wrote:

    (There are some very very rare cases where a turn of PTFE under/over an olive can let you remake a join where there is a nick or score in the
    pipe that is preventing it from sealing normally (I recall needing to
    use this technique once only!).

    I've had to use this bodge once when replacing a failed service valve*
    between plastic and copper pipe. The olive on the plastic pipe wouldn't
    seal (occasional drip) and half a dozen turns of PTFE tape around the
    olive cured the problem.

    *common problem with valve - extremely hard to turn off and then dripped
    from the from the turn-off adjustment when turned back on.
    --
    mailto : news {at} admac {dot} myzen {dot} co {dot} uk
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From The Natural Philosopher@tnp@invalid.invalid to uk.d-i-y on Sun Nov 15 10:58:44 2026
    From Newsgroup: uk.d-i-y

    On 15/11/2026 10:44, alan_m wrote:
    I've had to use this bodge once when replacing a failed service valve* between plastic and copper pipe. The olive on the plastic pipe...
    ...is an absolute nono. You NEVER use an olive on a plastic pipe.
    You use inserts and a fittings with an O-ring.
    --
    "Women actually are capable of being far more than the feminists will
    let them."



    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Chris Green@cl@isbd.net to uk.d-i-y on Sun Nov 15 11:28:10 2026
    From Newsgroup: uk.d-i-y

    The Natural Philosopher <tnp@invalid.invalid> wrote:
    On 15/11/2026 10:44, alan_m wrote:
    I've had to use this bodge once when replacing a failed service valve* between plastic and copper pipe. The olive on the plastic pipe...
    ...is an absolute nono. You NEVER use an olive on a plastic pipe.
    You use inserts and a fittings with an O-ring.

    I've come across some fittings for MDPE that use olives, though most use O-rings as you say.
    --
    Chris Green
    -+
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Tricky Dicky@tricky.dicky@sky.com to uk.d-i-y on Sun Nov 15 11:57:28 2026
    From Newsgroup: uk.d-i-y

    Chris Green <cl@isbd.net> wrote:
    The Natural Philosopher <tnp@invalid.invalid> wrote:
    On 15/11/2026 10:44, alan_m wrote:
    I've had to use this bodge once when replacing a failed service valve*
    between plastic and copper pipe. The olive on the plastic pipe...
    ...is an absolute nono. You NEVER use an olive on a plastic pipe.
    You use inserts and a fittings with an O-ring.

    I've come across some fittings for MDPE that use olives, though most use O-rings as you say.


    Compression fittings can be used with plastic pipe but as TNP has pointed
    out you have to use pipe inserts.

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From alan_m@junk@admac.myzen.co.uk to uk.d-i-y on Sun Nov 15 12:07:15 2026
    From Newsgroup: uk.d-i-y

    On 15/11/2026 10:58, The Natural Philosopher wrote:
    On 15/11/2026 10:44, alan_m wrote:
    I've had to use this bodge once when replacing a failed service valve*
    between plastic and copper pipe. The olive on the plastic pipe...
    ...is an absolute nono. You NEVER use an olive on a plastic pipe.
    You use inserts and a fittings with an O-ring.


    This wasn't my original plumbing but using an olive on plastic is a
    valid method. O rings for push fit, olives for compression fittings.

    I was replacing a failed flush mechanism in a toilet. I wasn't intending
    to replace the isolation valve until it started dripping after I had successfully repaired the toilet.

    The plastic pipe had the insert and was (originally) joined as a
    compression fitting to the isolation service valve using an olive. I
    replaced like with like keeping the old olive and connecting nut. I
    didn't want to risk cutting into a plastic pipe to get the olive off
    plus I only had a inch or so of plastic pipe sticking out of the tiled
    boxed in pipework. The leak afterwards was of the order of one drip
    every couple of minutes, zero drips after applying the PTFE tape.
    --
    mailto : news {at} admac {dot} myzen {dot} co {dot} uk
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From The Natural Philosopher@tnp@invalid.invalid to uk.d-i-y on Sun Nov 15 13:41:53 2026
    From Newsgroup: uk.d-i-y

    On 15/11/2026 12:07, alan_m wrote:
    On 15/11/2026 10:58, The Natural Philosopher wrote:
    On 15/11/2026 10:44, alan_m wrote:
    I've had to use this bodge once when replacing a failed service
    valve* between plastic and copper pipe. The olive on the plastic pipe...
    ...is an absolute nono. You NEVER use an olive on a plastic pipe.
    You use inserts and a fittings with an O-ring.


    This wasn't my original plumbing but using an olive on plastic is a
    valid method. O rings for push fit, olives for compression fittings.

    All my plastic fittings use O-rings and inserts

    I was replacing a failed flush mechanism in a toilet. I wasn't intending
    to replace the isolation valve until it started dripping after I had successfully repaired the toilet.

    The plastic pipe had the insert and was (originally) joined as a
    compression fitting to the isolation service valve using an olive. I replaced like with like keeping the old olive and connecting nut. I
    didn't want to risk cutting into a plastic pipe to get the olive off
    plus I only had a inch or so of plastic pipe sticking out of the tiled
    boxed in pipework. The leak afterwards was of the order of one drip
    every couple of minutes, zero drips after applying the PTFE tape.

    Total amateur bodge
    Olives are never used. Its all push fit. Get the right shit
    --
    Microsoft : the best reason to go to Linux that ever existed.

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From The Natural Philosopher@tnp@invalid.invalid to uk.d-i-y on Sun Nov 15 13:42:50 2026
    From Newsgroup: uk.d-i-y

    On 15/11/2026 11:57, Tricky Dicky wrote:
    Chris Green <cl@isbd.net> wrote:
    The Natural Philosopher <tnp@invalid.invalid> wrote:
    On 15/11/2026 10:44, alan_m wrote:
    I've had to use this bodge once when replacing a failed service valve* >>>> between plastic and copper pipe. The olive on the plastic pipe...
    ...is an absolute nono. You NEVER use an olive on a plastic pipe.
    You use inserts and a fittings with an O-ring.

    I've come across some fittings for MDPE that use olives, though most use
    O-rings as you say.


    Compression fittings can be used with plastic pipe but as TNP has pointed
    out you have to use pipe inserts.

    Even then its a shit idea. Inserts and push fits
    --
    rCLPolitics is the art of looking for trouble, finding it everywhere, diagnosing it incorrectly and applying the wrong remedies.rCY
    rCo Groucho Marx

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From alan_m@junk@admac.myzen.co.uk to uk.d-i-y on Sun Nov 15 16:32:51 2026
    From Newsgroup: uk.d-i-y

    On 15/11/2026 13:41, The Natural Philosopher wrote:

    Total amateur bodge
    Olives are never used. Its all push fit. Get the right shit

    The manufacturer of one of the commonly available plastic pipes produces
    two types of insert. One for plastic and one for (brass) compression
    fittings.
    --
    mailto : news {at} admac {dot} myzen {dot} co {dot} uk
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From John Rumm@see.my.signature@nowhere.null to uk.d-i-y on Sun Nov 15 17:30:37 2026
    From Newsgroup: uk.d-i-y

    On 15/11/2026 10:58, The Natural Philosopher wrote:
    On 15/11/2026 10:44, alan_m wrote:
    I've had to use this bodge once when replacing a failed service valve*
    between plastic and copper pipe. The olive on the plastic pipe...
    ...is an absolute nono. You NEVER use an olive on a plastic pipe.

    Ah, not just wrong, but confidently wrong... always the most
    entertaining type...

    You use inserts and a fittings with an O-ring.
    Insert yes, always.

    However compression fitting on a plastic pipe is also perfectly
    acceptable so long as the fitting has enough socket depth to ensure that
    the olive bites onto the pipe where it is supported by the insert.

    Some brands also recommend soft copper olives in preference to brass.

    See the Speedfit tech docs for details, page 14:

    https://www.johnguest.com/sites/jg/files/2022-01/RWC11339_JG-Speedfit-Technical-Specs-Guide_v11.pdf
    --
    Cheers,

    John.

    /=================================================================\
    | Internode Ltd - http://www.internode.co.uk | |-----------------------------------------------------------------|
    | John Rumm - john(at)internode(dot)co(dot)uk | \=================================================================/
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From John Rumm@see.my.signature@nowhere.null to uk.d-i-y on Sun Nov 15 17:45:35 2026
    From Newsgroup: uk.d-i-y

    On 15/11/2026 13:41, The Natural Philosopher wrote:
    On 15/11/2026 12:07, alan_m wrote:
    On 15/11/2026 10:58, The Natural Philosopher wrote:
    On 15/11/2026 10:44, alan_m wrote:
    I've had to use this bodge once when replacing a failed service
    valve* between plastic and copper pipe. The olive on the plastic
    pipe...
    ...is an absolute nono. You NEVER use an olive on a plastic pipe.
    You use inserts and a fittings with an O-ring.


    This wasn't my original plumbing but using an olive on plastic is a
    valid method. O rings for push fit, olives for compression fittings.

    All my plastic fittings use O-rings and inserts

    We are talking about brass fittings, not plastic.

    I was replacing a failed flush mechanism in a toilet. I wasn't
    intending to replace the isolation valve until it started dripping
    after I had successfully repaired the toilet.

    The plastic pipe had the insert and was (originally) joined as a
    compression fitting to the isolation service valve using an olive. I
    replaced like with like keeping the old olive and connecting nut. I
    didn't want to risk cutting into a plastic pipe to get the olive off
    plus I only had a inch or so of plastic pipe sticking out of the tiled
    boxed in pipework. The leak afterwards was of the order of one drip
    every couple of minutes, zero drips after applying the PTFE tape.


    Total amateur bodge

    A bodge I would expect a professional to make as well in preference to
    ripping out a customer's pipework boxing...

    Olives are never used. Its all push fit. Get the right shit

    It sounds like you ought you ought to let Waivn know they have made the exactly same mistake in their Hep20 technical reference that John Guest
    did in their Speedfit one:

    https://orbia.blob.core.windows.net/assets/F-47058-0.pdf

    (Page 24. Step 2, should get you really excited!)
    --
    Cheers,

    John.

    /=================================================================\
    | Internode Ltd - http://www.internode.co.uk | |-----------------------------------------------------------------|
    | John Rumm - john(at)internode(dot)co(dot)uk | \=================================================================/
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Roger Hayter@roger@hayter.org to uk.d-i-y on Mon Nov 16 17:11:34 2026
    From Newsgroup: uk.d-i-y

    On 15 Nov 2026 at 17:45:35 GMT+0, "John Rumm" <see.my.signature@nowhere.null> wrote:

    On 15/11/2026 13:41, The Natural Philosopher wrote:
    On 15/11/2026 12:07, alan_m wrote:
    On 15/11/2026 10:58, The Natural Philosopher wrote:
    On 15/11/2026 10:44, alan_m wrote:
    I've had to use this bodge once when replacing a failed service
    valve* between plastic and copper pipe. The olive on the plastic
    pipe...
    ...is an absolute nono. You NEVER use an olive on a plastic pipe.
    You use inserts and a fittings with an O-ring.


    This wasn't my original plumbing but using an olive on plastic is a
    valid method. O rings for push fit, olives for compression fittings.

    All my plastic fittings use O-rings and inserts

    We are talking about brass fittings, not plastic.

    I was replacing a failed flush mechanism in a toilet. I wasn't
    intending to replace the isolation valve until it started dripping
    after I had successfully repaired the toilet.

    The plastic pipe had the insert and was (originally) joined as a
    compression fitting to the isolation service valve using an olive. I
    replaced like with like keeping the old olive and connecting nut. I
    didn't want to risk cutting into a plastic pipe to get the olive off
    plus I only had a inch or so of plastic pipe sticking out of the tiled
    boxed in pipework. The leak afterwards was of the order of one drip
    every couple of minutes, zero drips after applying the PTFE tape.


    Total amateur bodge

    A bodge I would expect a professional to make as well in preference to ripping out a customer's pipework boxing...

    Olives are never used. Its all push fit. Get the right shit

    It sounds like you ought you ought to let Waivn know they have made the exactly same mistake in their Hep20 technical reference that John Guest
    did in their Speedfit one:

    https://orbia.blob.core.windows.net/assets/F-47058-0.pdf

    (Page 24. Step 2, should get you really excited!)

    I note with interest that they appear to show the PTFE tape *under* rather
    than over the olive. When I have used it with used pipes and fittings I have tended to use both, though this is a bit fiddly. But it seals the olive joint with the pipe as well as with the fitting.
    --

    Roger Hayter
    --- Synchronet 3.22a-Linux NewsLink 1.2