• Re: Shed Lighting - LED Batten Light

    From John Rumm@see.my.signature@nowhere.null to uk.d-i-y on Wed Nov 4 18:29:13 2026
    From Newsgroup: uk.d-i-y

    On 28/10/2026 19:49, Generalie wrote:
    Hi All

    Just looking at a strip light for my new shed (AKA man cave).

    I have little knowledge of LEDs but expect that the link below would probably be appropriate.

    https://www.toolstation.com/v-tac-super-slim-led-batten-light/pAI628


    Was on the point of buying in Toolstation, when the subject of IP rating crossed my mind.

    Is it usual/acceptable to install a fitting rated IP20 in a shed or
    similar outbuilding?-a Or is a higher spec mandated?

    If the shed it properly waterproof, then it would be ok.
    --
    Cheers,

    John.

    /=================================================================\
    | Internode Ltd - http://www.internode.co.uk | |-----------------------------------------------------------------|
    | John Rumm - john(at)internode(dot)co(dot)uk | \=================================================================/
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Marland@gemehabal@btinternet.co.uk to uk.d-i-y on Wed Nov 4 19:00:45 2026
    From Newsgroup: uk.d-i-y

    Generalie <Generalie@nospam.com> wrote:
    Hi All

    Just looking at a strip light for my new shed (AKA man cave).

    I have little knowledge of LEDs but expect that the link below would probably be appropriate.

    https://www.toolstation.com/v-tac-super-slim-led-batten-light/pAI628


    Was on the point of buying in Toolstation, when the subject of IP rating crossed my mind.

    Is it usual/acceptable to install a fitting rated IP20 in a shed or
    similar outbuilding? Or is a higher spec mandated?

    Thanks


    Phil


    Man Cave suggests you are going to spend some time in there, do think that
    one will give enough illumination in the right places.
    Sheds tend to be dark to start with due to small windows and dark surfaces
    , even if you paint the inside a light colour most of us with sheds have shelves of things that donrCOt reflect. Height can affect the light spread
    as well as many sheds have a fairly low ceiling.
    I Have two similar lights in a 12rCO x 8rCO shed each mounted near the end and occasionally still want a bit more to avoid working in shadow so have
    another centrally as well , that one has a movement sensor so comes on when
    I enter the door, useful if carrying something . Goes out if no movement detected after around 5 mins. ThatrCOs plenty enough to illuminate the path alongside via the windows when I leave and saves bothering with an outside light.

    GH

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Sam Plusnet@not@home.com to uk.d-i-y on Wed Nov 4 20:46:20 2026
    From Newsgroup: uk.d-i-y

    On 04/11/2026 19:00, Marland wrote:
    Generalie <Generalie@nospam.com> wrote:
    Hi All

    Just looking at a strip light for my new shed (AKA man cave).

    I have little knowledge of LEDs but expect that the link below would
    probably be appropriate.

    https://www.toolstation.com/v-tac-super-slim-led-batten-light/pAI628


    Was on the point of buying in Toolstation, when the subject of IP rating
    crossed my mind.

    Is it usual/acceptable to install a fitting rated IP20 in a shed or
    similar outbuilding? Or is a higher spec mandated?

    Thanks


    Phil


    Man Cave suggests you are going to spend some time in there, do think that one will give enough illumination in the right places.
    Sheds tend to be dark to start with due to small windows and dark surfaces
    , even if you paint the inside a light colour most of us with sheds have shelves of things that donrCOt reflect. Height can affect the light spread as well as many sheds have a fairly low ceiling.
    I Have two similar lights in a 12rCO x 8rCO shed each mounted near the end and
    occasionally still want a bit more to avoid working in shadow so have another centrally as well , that one has a movement sensor so comes on when
    I enter the door, useful if carrying something . Goes out if no movement detected after around 5 mins. ThatrCOs plenty enough to illuminate the path alongside via the windows when I leave and saves bothering with an outside light.

    I would go with 'decent' general illumination, plus adjustable work
    lighting (maybe two lights to prevent deep shadows).
    I do have a few rechargeable motion sensitive lights in a
    storeroom/utility room. As you say, it makes like so much easier when
    you go in there with your hands full.
    --
    Sam Plusnet
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Generalie@Generalie@nospam.com to uk.d-i-y on Fri Nov 13 20:13:03 2026
    From Newsgroup: uk.d-i-y

    On 04/11/2026 18:29, John Rumm wrote:
    On 28/10/2026 19:49, Generalie wrote:
    Hi All

    Just looking at a strip light for my new shed (AKA man cave).

    I have little knowledge of LEDs but expect that the link below would
    probably be appropriate.

    https://www.toolstation.com/v-tac-super-slim-led-batten-light/pAI628


    Was on the point of buying in Toolstation, when the subject of IP
    rating crossed my mind.

    Is it usual/acceptable to install a fitting rated IP20 in a shed or
    similar outbuilding?-a Or is a higher spec mandated?

    If the shed it properly waterproof, then it would be ok.


    Thanks John

    The shed is new and waterproof.

    I went ahead and bought the single 5' batten light.
    In an 8x6 shed this is more than adequate even for moderate close work.

    Phil



    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Generalie@Generalie@nospam.com to uk.d-i-y on Fri Nov 13 20:26:03 2026
    From Newsgroup: uk.d-i-y

    On 04/11/2026 19:00, Marland wrote:
    Generalie <Generalie@nospam.com> wrote:
    Hi All

    Just looking at a strip light for my new shed (AKA man cave).

    I have little knowledge of LEDs but expect that the link below would
    probably be appropriate.

    https://www.toolstation.com/v-tac-super-slim-led-batten-light/pAI628


    Was on the point of buying in Toolstation, when the subject of IP rating
    crossed my mind.

    Is it usual/acceptable to install a fitting rated IP20 in a shed or
    similar outbuilding? Or is a higher spec mandated?

    Thanks


    Phil


    Man Cave suggests you are going to spend some time in there, do think that one will give enough illumination in the right places.
    Sheds tend to be dark to start with due to small windows and dark surfaces
    , even if you paint the inside a light colour most of us with sheds have shelves of things that donrCOt reflect. Height can affect the light spread as well as many sheds have a fairly low ceiling.
    I Have two similar lights in a 12rCO x 8rCO shed each mounted near the end and
    occasionally still want a bit more to avoid working in shadow so have another centrally as well , that one has a movement sensor so comes on when
    I enter the door, useful if carrying something . Goes out if no movement detected after around 5 mins. ThatrCOs plenty enough to illuminate the path alongside via the windows when I leave and saves bothering with an outside light.

    GH

    Thanks GH

    I went ahead and fitted a single LED batten lamp.
    This gives more than adequate coverage for my 8x6 shed.

    Fortunately we have an outside light which illuminates the route to the
    shed door, useful now nights are drawing in.
    Also , we had an additional window included in the shed spec, so during
    the day, the space has plenty of natural light.

    Phil


    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Generalie@Generalie@nospam.com to uk.d-i-y on Fri Nov 13 20:41:21 2026
    From Newsgroup: uk.d-i-y

    On 04/11/2026 20:46, Sam Plusnet wrote:
    On 04/11/2026 19:00, Marland wrote:
    Generalie <Generalie@nospam.com> wrote:
    Hi All

    Just looking at a strip light for my new shed (AKA man cave).

    I have little knowledge of LEDs but expect that the link below would
    probably be appropriate.

    https://www.toolstation.com/v-tac-super-slim-led-batten-light/pAI628


    Was on the point of buying in Toolstation, when the subject of IP rating >>> crossed my mind.

    Is it usual/acceptable to install a fitting rated IP20 in a shed or
    similar outbuilding?-a Or is a higher spec mandated?

    Thanks


    Phil


    Man Cave suggests you are going to spend some time in there, do think
    that
    one will give enough illumination in the right places.
    Sheds tend to be dark to start with due to small windows and dark
    surfaces
    , even if you paint the inside a light colour most of us with sheds have
    shelves of things that donrCOt reflect.-a Height can affect the light spread >> as well as many sheds have a fairly low ceiling.
    I Have two similar lights-a in a 12rCO x 8rCO shed each mounted near the
    end and
    occasionally still want a bit more to avoid working in shadow-a so have
    another centrally as well , that one has a movement sensor so comes on
    when
    I enter-a the door, useful if carrying something . Goes out if no movement >> detected after around 5 mins. ThatrCOs-a plenty enough-a to illuminate the >> path
    alongside via the windows when I leave and saves bothering with an
    outside
    light.

    I would go with 'decent' general illumination, plus adjustable work
    lighting (maybe two lights to prevent deep shadows).
    I do have a few rechargeable motion sensitive lights in a storeroom/
    utility room.-a As you say, it makes like so much easier when you go in there with your hands full.


    Thanks Sam

    I have fitted a single batten at the roof apex and this seems to provide sufficient light for all but very close work.

    I suspect that closer work will require a spectacle upgrade sooner than improved lighting :)

    Phil
    --- Synchronet 3.22a-Linux NewsLink 1.2