• Two-tone testing SSB Tx

    From liz@liz@poppyrecords.invalid.invalid (Liz Tuddenham) to sci.electronics.design on Mon Nov 9 16:57:48 2026
    From Newsgroup: sci.electronics.design

    I am nearing the end of a restoration job that has surprised me with the
    sheer number of faults I have found on the equipment. The item in
    question is a K.W. Viceroy SSB transmitter, which is needed for a
    vintage radio demonstration later this year or early next year
    (depending on how quickly I can get it working properly).

    I have put the circuit diagram at: http://www.poppyrecords.co.uk/other/ViceroyCircuit2e.gif

    The transmitter was a MkII but the power supply was a MkIII and I had to
    make a replacement for the missing control box which could interface
    between the two versions.

    I have now got all the stages working right up to the P.A. stage on 7.15
    Mc/s, my testing frequency, there is loads of grid drive to the two
    6146s. With a two-tone test, the waveform on the grids is nearly
    perfect right up to grid current, then it begin to flatten off if the
    grids are over-driven - so everyhting up to that point is behaving as
    expected.

    The HT to the anodes of the 6146s measures 700v and the screen grids
    measure 250v, the standard running voltages for a pair of these in
    'amateur service". The stage is correctly neutralised, both 'cold' and
    'hot'. When optimally loaded into a 60-ohm dummy load, an oscilloscope
    shows the output to be 100v p/p before clippig, which corresponds to 25W
    peak.

    Clearly something is wrong in the P.A. stage (which is supposed to give
    120W peak) but before I spend a lot of money on replacement 6146s, can
    anyone with experience of this sort of tranmitter make suggestion for
    other possible causes I could be looking for, rather than just 'flat'
    valves?
    --
    ~ Liz Tuddenham ~
    (Remove the ".invalid"s and add ".co.uk" to reply)
    www.poppyrecords.co.uk
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Jeff Liebermann@jeffl@cruzio.com to sci.electronics.design on Mon Nov 9 10:08:17 2026
    From Newsgroup: sci.electronics.design

    On Mon, 9 Nov 2026 16:57:48 +0000, liz@poppyrecords.invalid.invalid
    (Liz Tuddenham) wrote:

    I am nearing the end of a restoration job that has surprised me with the >sheer number of faults I have found on the equipment. The item in
    question is a K.W. Viceroy SSB transmitter, which is needed for a
    vintage radio demonstration later this year or early next year
    (depending on how quickly I can get it working properly).

    I have put the circuit diagram at: >http://www.poppyrecords.co.uk/other/ViceroyCircuit2e.gif

    The transmitter was a MkII but the power supply was a MkIII and I had to
    make a replacement for the missing control box which could interface
    between the two versions.

    I have now got all the stages working right up to the P.A. stage on 7.15 >Mc/s, my testing frequency, there is loads of grid drive to the two
    6146s. With a two-tone test, the waveform on the grids is nearly
    perfect right up to grid current, then it begin to flatten off if the
    grids are over-driven - so everyhting up to that point is behaving as >expected.

    The HT to the anodes of the 6146s measures 700v and the screen grids
    measure 250v, the standard running voltages for a pair of these in
    'amateur service". The stage is correctly neutralised, both 'cold' and >'hot'. When optimally loaded into a 60-ohm dummy load, an oscilloscope
    shows the output to be 100v p/p before clippig, which corresponds to 25W >peak.

    Clearly something is wrong in the P.A. stage (which is supposed to give
    120W peak) but before I spend a lot of money on replacement 6146s, can
    anyone with experience of this sort of tranmitter make suggestion for
    other possible causes I could be looking for, rather than just 'flat'
    valves?

    The two 6146 output tubes (V12 and V13) are in parallel. My guess(tm)
    is they might be mismatched. Try the two tone test with just one
    tube.

    Intermodulation is another name for a not very linear amplifier. Look
    at the PA input and output waveforms and check for visible distortion.
    Also, check if the 6146 output stages are operating in the linear
    region.

    The "loads of grid drive" might be a potential problem. Even a very
    linear output stage might produce distortion when overdriven.

    The ALC (automagic level control) seems rather odd. I don't see any
    capacitor filtering that could remove audio modulation from the
    rectified RF after the diodes V16 or around V4. If there was audio
    modulation superimposed on the ALC voltage, you will see considerable distortion.

    Check if the ALC actually works. Adjust the 50K potentiometer near
    V16 and see if the RF output goes up and down.
    --
    Jeff Liebermann jeffl@cruzio.com
    PO Box 272 http://www.LearnByDestroying.com
    Ben Lomond CA 95005-0272 AE6KS 831-336-2558

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From liz@liz@poppyrecords.invalid.invalid (Liz Tuddenham) to sci.electronics.design on Mon Nov 9 19:17:22 2026
    From Newsgroup: sci.electronics.design

    Jeff Liebermann <jeffl@cruzio.com> wrote:

    On Mon, 9 Nov 2026 16:57:48 +0000, liz@poppyrecords.invalid.invalid
    (Liz Tuddenham) wrote:

    I am nearing the end of a restoration job that has surprised me with the >sheer number of faults I have found on the equipment. The item in
    question is a K.W. Viceroy SSB transmitter, which is needed for a
    vintage radio demonstration later this year or early next year
    (depending on how quickly I can get it working properly).

    I have put the circuit diagram at: >http://www.poppyrecords.co.uk/other/ViceroyCircuit2e.gif

    The transmitter was a MkII but the power supply was a MkIII and I had to >make a replacement for the missing control box which could interface >between the two versions.

    I have now got all the stages working right up to the P.A. stage on 7.15 >Mc/s, my testing frequency, there is loads of grid drive to the two
    6146s. With a two-tone test, the waveform on the grids is nearly
    perfect right up to grid current, then it begin to flatten off if the
    grids are over-driven - so everyhting up to that point is behaving as >expected.

    The HT to the anodes of the 6146s measures 700v and the screen grids >measure 250v, the standard running voltages for a pair of these in
    'amateur service". The stage is correctly neutralised, both 'cold' and >'hot'. When optimally loaded into a 60-ohm dummy load, an oscilloscope >shows the output to be 100v p/p before clippig, which corresponds to 25W >peak.

    Clearly something is wrong in the P.A. stage (which is supposed to give >120W peak) but before I spend a lot of money on replacement 6146s, can >anyone with experience of this sort of tranmitter make suggestion for
    other possible causes I could be looking for, rather than just 'flat' >valves?

    The two 6146 output tubes (V12 and V13) are in parallel. My guess(tm)
    is they might be mismatched. Try the two tone test with just one
    tube.

    Thanks for that suggestion, there is a big difference between the two
    valves when they are inserted separately. Some of this might be
    accounted for by the need to re-tune everything because of the changes
    in valve capacitance, matching impdance and neutralisation but it looks
    pretty clear that one of the valves is almost dead.. It is possible that
    even the 'good' one is not as good as it should be, although it gets
    pretty hot on full power. I haven't got a valve tester, so I can't
    measure the peak emission.


    Intermodulation is another name for a not very linear amplifier. Look
    at the PA input and output waveforms and check for visible distortion.
    Also, check if the 6146 output stages are operating in the linear
    region.

    It is quite easy to alter the grid bias and the drive level
    independently so as to explore various operating conditions, the circuit appears to be quite tolerant over a reasonable range of adjustment and
    the output waveform looks good until it hits the flat top.


    The "loads of grid drive" might be a potential problem. Even a very
    linear output stage might produce distortion when overdriven.

    I can adjust it to give optimum results but the power is still low.


    The ALC (automagic level control) seems rather odd. I don't see any capacitor filtering that could remove audio modulation from the
    rectified RF after the diodes V16 or around V4. If there was audio modulation superimposed on the ALC voltage, you will see considerable distortion.

    It is there: there is a capacitor from the juntion of the two anodes of
    V16 to earth.


    Check if the ALC actually works. Adjust the 50K potentiometer near
    V16 and see if the RF output goes up and down.

    It sort-of does, although it doesn't have much effect at the power level
    I can achieve. I have tried unplugging the EB91 and the flat-topping
    doesn't improve.

    It all seems to point to low emission in the output valves, so it looks
    as though an expensive purchase is inevitable.
    --
    ~ Liz Tuddenham ~
    (Remove the ".invalid"s and add ".co.uk" to reply)
    www.poppyrecords.co.uk
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Edward Rawde@invalid@invalid.invalid to sci.electronics.design on Mon Nov 9 14:33:59 2026
    From Newsgroup: sci.electronics.design

    "Liz Tuddenham" <liz@poppyrecords.invalid.invalid> wrote in message news:1s4bff0.1cfp4wk1t5nyloN%liz@poppyrecords.invalid.invalid...
    I am nearing the end of a restoration job that has surprised me with the
    sheer number of faults I have found on the equipment. The item in
    question is a K.W. Viceroy SSB transmitter, which is needed for a
    vintage radio demonstration later this year or early next year
    (depending on how quickly I can get it working properly).

    I have put the circuit diagram at: http://www.poppyrecords.co.uk/other/ViceroyCircuit2e.gif

    The transmitter was a MkII but the power supply was a MkIII and I had to
    make a replacement for the missing control box which could interface
    between the two versions.

    I have now got all the stages working right up to the P.A. stage on 7.15 Mc/s, my testing frequency, there is loads of grid drive to the two
    6146s. With a two-tone test, the waveform on the grids is nearly
    perfect right up to grid current, then it begin to flatten off if the
    grids are over-driven - so everyhting up to that point is behaving as expected.

    The HT to the anodes of the 6146s measures 700v and the screen grids
    measure 250v, the standard running voltages for a pair of these in
    'amateur service". The stage is correctly neutralised, both 'cold' and 'hot'. When optimally loaded into a 60-ohm dummy load, an oscilloscope
    shows the output to be 100v p/p before clippig, which corresponds to 25W peak.

    Clearly something is wrong in the P.A. stage (which is supposed to give
    120W peak) but before I spend a lot of money on replacement 6146s,

    Maybe try these to see if there's a difference before deciding whether to
    get more expensive ones.

    https://www.ebay.com/itm/335278285334


    can
    anyone with experience of this sort of tranmitter make suggestion for
    other possible causes I could be looking for, rather than just 'flat'
    valves?

    --
    ~ Liz Tuddenham ~
    (Remove the ".invalid"s and add ".co.uk" to reply)
    www.poppyrecords.co.uk


    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Jeff Liebermann@jeffl@cruzio.com to sci.electronics.design on Mon Nov 9 12:43:11 2026
    From Newsgroup: sci.electronics.design

    On Mon, 9 Nov 2026 19:17:22 +0000, liz@poppyrecords.invalid.invalid
    (Liz Tuddenham) wrote:

    Jeff Liebermann <jeffl@cruzio.com> wrote:

    On Mon, 9 Nov 2026 16:57:48 +0000, liz@poppyrecords.invalid.invalid
    (Liz Tuddenham) wrote:

    I am nearing the end of a restoration job that has surprised me with the
    sheer number of faults I have found on the equipment. The item in
    question is a K.W. Viceroy SSB transmitter, which is needed for a
    vintage radio demonstration later this year or early next year
    (depending on how quickly I can get it working properly).

    I have put the circuit diagram at:
    http://www.poppyrecords.co.uk/other/ViceroyCircuit2e.gif

    Have you tried the various tuning instructions and test points in the
    manual?
    <https://www.retro.co.za/zs1ke/viceroy/G3XAQ/ViceroyMk3.pdf>
    Are the measurements in the PA section reasonable (Section 5-3)?

    The idle anode current should be about 50 ma. See Section 3-2(4). I
    think it means 50 ma with both 6146 tubes functioning. Is the idle
    anode current equally divided between the two tubes?
    --
    Jeff Liebermann jeffl@cruzio.com
    PO Box 272 http://www.LearnByDestroying.com
    Ben Lomond CA 95005-0272 AE6KS 831-336-2558

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From liz@liz@poppyrecords.invalid.invalid (Liz Tuddenham) to sci.electronics.design on Mon Nov 9 21:55:38 2026
    From Newsgroup: sci.electronics.design

    Jeff Liebermann <jeffl@cruzio.com> wrote:

    On Mon, 9 Nov 2026 19:17:22 +0000, liz@poppyrecords.invalid.invalid
    (Liz Tuddenham) wrote:

    Jeff Liebermann <jeffl@cruzio.com> wrote:

    On Mon, 9 Nov 2026 16:57:48 +0000, liz@poppyrecords.invalid.invalid
    (Liz Tuddenham) wrote:

    I am nearing the end of a restoration job that has surprised me with the >> >sheer number of faults I have found on the equipment. The item in
    question is a K.W. Viceroy SSB transmitter, which is needed for a
    vintage radio demonstration later this year or early next year
    (depending on how quickly I can get it working properly).

    I have put the circuit diagram at:
    http://www.poppyrecords.co.uk/other/ViceroyCircuit2e.gif

    Have you tried the various tuning instructions and test points in the
    manual?
    <https://www.retro.co.za/zs1ke/viceroy/G3XAQ/ViceroyMk3.pdf>
    Are the measurements in the PA section reasonable (Section 5-3)?

    The manual is for the MkIII, this is a MkII, a lot of ot applies to the
    MkII but there are some significant differences so I am having to fall
    back on my own general knowledge of these things, The drive stages have
    lined up all right (at least, on the 7 Mc/s band) but I have found all
    sorts of faults in both the hardware and the original design (e.g.
    cathode followers that didn't, turns removed from the VFO coil,
    valveholders with pins broken).


    The idle anode current should be about 50 ma. See Section 3-2(4). I
    think it means 50 ma with both 6146 tubes functioning. Is the idle
    anode current equally divided between the two tubes?

    There is a note in the few sheets of paper tha pass for instructions (apparently typed by one of the previous users to assist others who
    couldn't get it to work) which suggest that the standing current with no
    drive should be lowered from 50mA indicated on the meter scale to 40mA.
    As I had to replace the burnt-out meter and make a new scale, I put the
    mark on my scale at 40mA.

    Whether that is shared equally between the two valves is not easy to
    determine as it would either mean disconnecting a lot of the cathode
    wiring around the valveholder, or putting a meter in series with the top
    cap anode feed (at +700 volts)- neither of which I would be
    particularly keen to do.

    I suspect that, with the present pair of valves, the currents would be a
    long way out of balance.
    --
    ~ Liz Tuddenham ~
    (Remove the ".invalid"s and add ".co.uk" to reply)
    www.poppyrecords.co.uk
    --- Synchronet 3.22a-Linux NewsLink 1.2