• All the Squishers Suck

    From Bob La Londe@none@none.com99 to rec.crafts.metalworking on Sun Nov 8 11:52:40 2026
    From Newsgroup: rec.crafts.metalworking

    I have several insulated wire terminal crimpers and they all pretty much
    suck. The only ones that hold are the kind the pierce or nearly pierce
    the insulation like with a non insulated terminal crimper. Odly the bst
    is the cheapo that came with the 9.95 all in one crap set fromt eh
    discount auto parts store. Noen fo the expensive or very expensive name brands work very well anymore.

    Years ago a buddy of mine show me a regular stamped sheet metal
    combination stripper crimper sold by Napa Autoparts The crimping dies
    were a square parallel surface and they worked. They just worked. Any
    wire within the range for the terminal was solidly crimped in. Not long
    after I found Klein made a pair that was identical except for the color
    of the handles. Klein might have made the Napa tool for all I know.
    They are no longer available. They worked with any wire in the range of
    the terminal. Not just the maximum size rated for the terminal like everything out there today.

    AI pretty much recommended those with near piercing style dies. T&B
    (1111) or Klien (1005) forward plier style. Mostly made for
    noninsulated terminals.

    I decided to try this one which I think is a Klein although McMaster
    doesn't reveal that in their details.

    7289K1 https://www.mcmaster.com/products/7289k1/

    If they turn out to be another POS crimper I'm just going to fucking
    make my own. I have a drawer full of pliers of various types I almost
    never use, lots of grinding tools, I can always take a shot at hard
    milling, and I have enough 4140 on hand to make a thousand pairs of
    pliers if I can just figure out the best heat treat.
    --
    Bob La Londe
    CNC Molds N Stuff

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Jim Wilkins@muratlanne@gmail.com to rec.crafts.metalworking on Sun Nov 8 17:56:38 2026
    From Newsgroup: rec.crafts.metalworking

    "Bob La Londe" wrote in message news:11cqgdp$1nnn5$1@dont-email.me...

    I have several insulated wire terminal crimpers and they all pretty much
    suck. The only ones that hold are the kind the pierce or nearly pierce
    the insulation like with a non insulated terminal crimper. Odly the bst
    is the cheapo that came with the 9.95 all in one crap set fromt eh
    discount auto parts store. Noen fo the expensive or very expensive name
    brands work very well anymore.

    ---------------------------

    I generally get good results from the hardware store crimper that also
    shears screws. The industrial ones from flea markets tend to be worn from heavy use without oiling, I've shimmed under the jaws of some to tighten
    them.

    For high current crimps on batteries and inverters I test the resistance or check for heating with a thermal imager, or both. Before finding the micro ohmmeter I passed 1A or 10A through the crimp and measured the drop, at 1A
    1mV indicates 1 milliOhm. A car light bulb is a handy current limiting resistor from a 12V power source.

    Although it's frowned on I solder the open end with fine solder which gives good control of the amount melted into the joint, to avoid filling it and creating a stress concentration in the stranded wire exiting the crimp.


    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Snag@Snag_one@msn.com to rec.crafts.metalworking on Sun Nov 8 21:21:52 2026
    From Newsgroup: rec.crafts.metalworking

    On 11/8/2026 4:56 PM, Jim Wilkins wrote:
    "Bob La Londe"-a wrote in message news:11cqgdp$1nnn5$1@dont-email.me...

    I have several insulated wire terminal crimpers and they all pretty much suck.-a The only ones that hold are the kind the pierce or nearly pierce
    the insulation like with a non insulated terminal crimper.-a Odly the bst
    is the cheapo that came with the 9.95 all in one crap set fromt eh
    discount auto parts store.-a Noen fo the expensive or very expensive name brands work very well anymore.

    ---------------------------

    I generally get good results from the hardware store crimper that also shears screws. The industrial ones from flea markets tend to be worn
    from heavy use without oiling, I've shimmed under the jaws of some to tighten them.

    For high current crimps on batteries and inverters I test the resistance
    or check for heating with a thermal imager, or both. Before finding the micro ohmmeter I passed 1A or 10A through the crimp and measured the
    drop, at 1A 1mV indicates 1 milliOhm. A car light bulb is a handy
    current limiting resistor from a 12V power source.

    Although it's frowned on I solder the open end with fine solder which
    gives good control of the amount melted into the joint, to avoid filling
    it and creating a stress concentration in the stranded wire exiting the crimp.



    I've got a couple of pair of the "hardware store" variety . I use the
    part for non-insulated that punches thru the insulated sleeve . Nothing
    I do is sensitive enough to need milliamp precision .
    --
    Snag
    Muslims hate dogs because they
    protect women , children, and goats .
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Carl@carl.ijamesXX@YYverizon.net to rec.crafts.metalworking on Mon Nov 9 09:35:27 2026
    From Newsgroup: rec.crafts.metalworking

    On 11/8/26 1:52 PM, Bob La Londe wrote:
    I have several insulated wire terminal crimpers and they all pretty much suck.-a The only ones that hold are the kind the pierce or nearly pierce
    the insulation like with a non insulated terminal crimper.-a Odly the bst
    is the cheapo that came with the 9.95 all in one crap set fromt eh
    discount auto parts store.-a Noen fo the expensive or very expensive name brands work very well anymore.

    Years ago a buddy of mine show me a regular stamped sheet metal
    combination stripper crimper sold by Napa Autoparts-a The crimping dies
    were a square parallel surface and they worked.-a They just worked.-a Any wire within the range for the terminal was solidly crimped in.-a Not long after I found Klein made a pair that was identical except for the color
    of the handles.-a Klein might have made the Napa tool for all I know.
    They are no longer available.-a They worked with any wire in the range of the terminal.-a Not just the maximum size rated for the terminal like everything out there today.

    AI pretty much recommended those with near piercing style dies.-a T&B
    (1111) or Klien (1005) forward plier style.-a Mostly made for
    noninsulated terminals.

    I decided to try this one which I think is a Klein although McMaster
    doesn't reveal that in their details.

    7289K1 https://www.mcmaster.com/products/7289k1/

    If you call McMaster Carr and ask, they will tell you the brand and
    part/model number. At least they used to years ago.


    If they turn out to be another POS crimper I'm just going to fucking
    make my own.-a I have a drawer full of pliers of various types I almost never use, lots of grinding tools, I can always take a shot at hard
    milling, and I have enough 4140 on hand to make a thousand pairs of
    pliers if I can just figure out the best heat treat.
    --
    Regards,
    Carl
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Bob La Londe@none@none.com99 to rec.crafts.metalworking on Mon Nov 9 13:35:12 2026
    From Newsgroup: rec.crafts.metalworking

    On 11/9/2026 7:35 AM, Carl wrote:
    On 11/8/26 1:52 PM, Bob La Londe wrote:
    I have several insulated wire terminal crimpers and they all pretty
    much suck.-a The only ones that hold are the kind the pierce or nearly
    pierce the insulation like with a non insulated terminal crimper.
    Odly the bst is the cheapo that came with the 9.95 all in one crap set
    fromt eh discount auto parts store.-a Noen fo the expensive or very
    expensive name brands work very well anymore.

    Years ago a buddy of mine show me a regular stamped sheet metal
    combination stripper crimper sold by Napa Autoparts-a The crimping dies
    were a square parallel surface and they worked.-a They just worked.
    Any wire within the range for the terminal was solidly crimped in.
    Not long after I found Klein made a pair that was identical except for
    the color of the handles.-a Klein might have made the Napa tool for all
    I know. They are no longer available.-a They worked with any wire in
    the range of the terminal.-a Not just the maximum size rated for the
    terminal like everything out there today.

    AI pretty much recommended those with near piercing style dies.-a T&B
    (1111) or Klien (1005) forward plier style.-a Mostly made for
    noninsulated terminals.

    I decided to try this one which I think is a Klein although McMaster
    doesn't reveal that in their details.

    7289K1 https://www.mcmaster.com/products/7289k1/

    If you call McMaster Carr and ask, they will tell you the brand and part/model number.-a At least they used to years ago.


    It looks like a Klein 1005 to me, and its only a dollar more than the
    Amazon price so I ordered one. There is also a Harbor Freight Icon that
    has similar jaws, but also scissor style wire strippers in the back half
    I plan to look at for $10 less than the Klein's (when on sale) or the
    same price regularly.

    I may take a hand full of scrap wire and cheap terminals with me to the
    Harbor freight store, test it in the parking lot, and return it in
    minutes if it sucks.





    If they turn out to be another POS crimper I'm just going to fucking
    make my own.-a I have a drawer full of pliers of various types I almost
    never use, lots of grinding tools, I can always take a shot at hard
    milling, and I have enough 4140 on hand to make a thousand pairs of
    pliers if I can just figure out the best heat treat.
    --
    Bob La Londe
    CNC Molds N Stuff
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From David Billington@djb@invalid.com to rec.crafts.metalworking on Mon Nov 9 20:56:23 2026
    From Newsgroup: rec.crafts.metalworking

    On 09/11/2026 20:35, Bob La Londe wrote:
    On 11/9/2026 7:35 AM, Carl wrote:
    On 11/8/26 1:52 PM, Bob La Londe wrote:
    I have several insulated wire terminal crimpers and they all pretty
    much suck.-a The only ones that hold are the kind the pierce or
    nearly pierce the insulation like with a non insulated terminal
    crimper.-a Odly the bst is the cheapo that came with the 9.95 all in
    one crap set fromt eh discount auto parts store.-a Noen fo the
    expensive or very expensive name brands work very well anymore.

    Years ago a buddy of mine show me a regular stamped sheet metal
    combination stripper crimper sold by Napa Autoparts-a The crimping
    dies were a square parallel surface and they worked. They just
    worked.-a Any wire within the range for the terminal was solidly
    crimped in.-a Not long after I found Klein made a pair that was
    identical except for the color of the handles. Klein might have made
    the Napa tool for all I know. They are no longer available.-a They
    worked with any wire in the range of the terminal.-a Not just the
    maximum size rated for the terminal like everything out there today.

    AI pretty much recommended those with near piercing style dies.-a T&B
    (1111) or Klien (1005) forward plier style. Mostly made for
    noninsulated terminals.

    I decided to try this one which I think is a Klein although McMaster
    doesn't reveal that in their details.

    7289K1 https://www.mcmaster.com/products/7289k1/

    If you call McMaster Carr and ask, they will tell you the brand and
    part/model number.-a At least they used to years ago.


    It looks like a Klein 1005 to me, and its only a dollar more than the
    Amazon price so I ordered one.-a There is also a Harbor Freight Icon
    that has similar jaws, but also scissor style wire strippers in the
    back half I plan to look at for $10 less than the Klein's (when on
    sale) or the same price regularly.

    I may take a hand full of scrap wire and cheap terminals with me to
    the Harbor freight store, test it in the parking lot, and return it in minutes if it sucks.





    If they turn out to be another POS crimper I'm just going to fucking
    make my own.-a I have a drawer full of pliers of various types I
    almost never use, lots of grinding tools, I can always take a shot
    at hard milling, and I have enough 4140 on hand to make a thousand
    pairs of pliers if I can just figure out the best heat treat.


    See if the ones you look at have instructions for the terminal
    orientation, mine didn't come with any but I found it online after a bit
    of-a looking. The jaws on mine are asymmetric with one side crimping the section around the wire insulation and the other the section that holds
    the conductor, it also marks the crimp to indicate that the correct
    crimp has been used. 1 dot for red, 2 dots for blue, a bar for yellow.
    I've seen various of these crimpers that don't have asymmetric jaws and
    don't know how they perform. I've not had any issues with the crimping
    with the crimper I have.

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Clare Snyder@clare@snyder.on.ca to rec.crafts.metalworking on Mon Nov 9 16:54:37 2026
    From Newsgroup: rec.crafts.metalworking

    On Mon, 9 Nov 2026 13:35:12 -0700, Bob La Londe <none@none.com99>
    wrote:

    On 11/9/2026 7:35 AM, Carl wrote:
    On 11/8/26 1:52 PM, Bob La Londe wrote:
    I have several insulated wire terminal crimpers and they all pretty
    much suck.a The only ones that hold are the kind the pierce or nearly
    pierce the insulation like with a non insulated terminal crimper.
    Odly the bst is the cheapo that came with the 9.95 all in one crap set
    fromt eh discount auto parts store.a Noen fo the expensive or very
    expensive name brands work very well anymore.

    Years ago a buddy of mine show me a regular stamped sheet metal
    combination stripper crimper sold by Napa Autopartsa The crimping dies
    were a square parallel surface and they worked.a They just worked.
    Any wire within the range for the terminal was solidly crimped in.
    Not long after I found Klein made a pair that was identical except for
    the color of the handles.a Klein might have made the Napa tool for all
    I know. They are no longer available.a They worked with any wire in
    the range of the terminal.a Not just the maximum size rated for the
    terminal like everything out there today.

    AI pretty much recommended those with near piercing style dies.a T&B
    (1111) or Klien (1005) forward plier style.a Mostly made for
    noninsulated terminals.

    I decided to try this one which I think is a Klein although McMaster
    doesn't reveal that in their details.

    7289K1 https://www.mcmaster.com/products/7289k1/

    If you call McMaster Carr and ask, they will tell you the brand and
    part/model number.a At least they used to years ago.


    It looks like a Klein 1005 to me, and its only a dollar more than the
    Amazon price so I ordered one. There is also a Harbor Freight Icon that
    has similar jaws, but also scissor style wire strippers in the back half
    I plan to look at for $10 less than the Klein's (when on sale) or the
    same price regularly.

    I may take a hand full of scrap wire and cheap terminals with me to the >Harbor freight store, test it in the parking lot, and return it in
    minutes if it sucks.





    If they turn out to be another POS crimper I'm just going to fucking
    make my own.a I have a drawer full of pliers of various types I almost
    never use, lots of grinding tools, I can always take a shot at hard
    milling, and I have enough 4140 on hand to make a thousand pairs of
    pliers if I can just figure out the best heat treat.


    I got this one:" https://www.princessauto.com/en/product/pa0009480492-6-pc-quick-change-ratcheting-crimper/PA0009480492?srsltid=AYCX9vJTdUyuL4VeaeQpHliEiwFy8xsMIbIfeXudmMNOQjQd2qgmXZod.
    Cheap at 3x the price!!!
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Jim Wilkins@muratlanne@gmail.com to rec.crafts.metalworking on Mon Nov 9 17:42:17 2026
    From Newsgroup: rec.crafts.metalworking

    "Clare Snyder" wrote in message news:n7g4flhijbafnh75tg3n47c83eplul41sg@4ax.com...
    ...
    When I was wiring machinery full time there was no problem with name brand tools and terminals. Since retiring I've been using whatever I could find
    for tools and terminals, and have some failures with off brand terminals
    with thinner insulation sleeves or other variations.

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Bob La Londe@none@none.com99 to rec.crafts.metalworking on Mon Nov 9 15:54:25 2026
    From Newsgroup: rec.crafts.metalworking

    On 11/9/2026 2:54 PM, Clare Snyder wrote:
    On Mon, 9 Nov 2026 13:35:12 -0700, Bob La Londe <none@none.com99>
    wrote:

    On 11/9/2026 7:35 AM, Carl wrote:
    On 11/8/26 1:52 PM, Bob La Londe wrote:
    I have several insulated wire terminal crimpers and they all pretty
    much suck.-a The only ones that hold are the kind the pierce or nearly >>>> pierce the insulation like with a non insulated terminal crimper.
    Odly the bst is the cheapo that came with the 9.95 all in one crap set >>>> fromt eh discount auto parts store.-a Noen fo the expensive or very
    expensive name brands work very well anymore.

    Years ago a buddy of mine show me a regular stamped sheet metal
    combination stripper crimper sold by Napa Autoparts-a The crimping dies >>>> were a square parallel surface and they worked.-a They just worked.
    Any wire within the range for the terminal was solidly crimped in.
    Not long after I found Klein made a pair that was identical except for >>>> the color of the handles.-a Klein might have made the Napa tool for all >>>> I know. They are no longer available.-a They worked with any wire in
    the range of the terminal.-a Not just the maximum size rated for the
    terminal like everything out there today.

    AI pretty much recommended those with near piercing style dies.-a T&B
    (1111) or Klien (1005) forward plier style.-a Mostly made for
    noninsulated terminals.

    I decided to try this one which I think is a Klein although McMaster
    doesn't reveal that in their details.

    7289K1 https://www.mcmaster.com/products/7289k1/

    If you call McMaster Carr and ask, they will tell you the brand and
    part/model number.-a At least they used to years ago.


    It looks like a Klein 1005 to me, and its only a dollar more than the
    Amazon price so I ordered one. There is also a Harbor Freight Icon that
    has similar jaws, but also scissor style wire strippers in the back half
    I plan to look at for $10 less than the Klein's (when on sale) or the
    same price regularly.

    I may take a hand full of scrap wire and cheap terminals with me to the
    Harbor freight store, test it in the parking lot, and return it in
    minutes if it sucks.





    If they turn out to be another POS crimper I'm just going to fucking
    make my own.-a I have a drawer full of pliers of various types I almost >>>> never use, lots of grinding tools, I can always take a shot at hard
    milling, and I have enough 4140 on hand to make a thousand pairs of
    pliers if I can just figure out the best heat treat.


    I got this one:" https://www.princessauto.com/en/product/pa0009480492-6-pc-quick-change-ratcheting-crimper/PA0009480492?srsltid=AYCX9vJTdUyuL4VeaeQpHliEiwFy8xsMIbIfeXudmMNOQjQd2qgmXZod.
    Cheap at 3x the price!!!

    I have one almost identical except for the color of the handles.
    (actually a few for different types of termination). All of that style
    I have work great... except on insulated wire terminals. LOL. A light
    pull feels ok, but a firm pull and they come off.
    --
    Bob La Londe
    CNC Molds N Stuff
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Clare Snyder@clare@snyder.on.ca to rec.crafts.metalworking on Mon Nov 9 20:38:09 2026
    From Newsgroup: rec.crafts.metalworking

    On Mon, 9 Nov 2026 15:54:25 -0700, Bob La Londe <none@none.com99>
    wrote:

    On 11/9/2026 2:54 PM, Clare Snyder wrote:
    On Mon, 9 Nov 2026 13:35:12 -0700, Bob La Londe <none@none.com99>
    wrote:

    On 11/9/2026 7:35 AM, Carl wrote:
    On 11/8/26 1:52 PM, Bob La Londe wrote:
    I have several insulated wire terminal crimpers and they all pretty
    much suck.a The only ones that hold are the kind the pierce or nearly >>>>> pierce the insulation like with a non insulated terminal crimper.
    Odly the bst is the cheapo that came with the 9.95 all in one crap set >>>>> fromt eh discount auto parts store.a Noen fo the expensive or very
    expensive name brands work very well anymore.

    Years ago a buddy of mine show me a regular stamped sheet metal
    combination stripper crimper sold by Napa Autopartsa The crimping dies >>>>> were a square parallel surface and they worked.a They just worked.
    Any wire within the range for the terminal was solidly crimped in.
    Not long after I found Klein made a pair that was identical except for >>>>> the color of the handles.a Klein might have made the Napa tool for all >>>>> I know. They are no longer available.a They worked with any wire in
    the range of the terminal.a Not just the maximum size rated for the
    terminal like everything out there today.

    AI pretty much recommended those with near piercing style dies.a T&B >>>>> (1111) or Klien (1005) forward plier style.a Mostly made for
    noninsulated terminals.

    I decided to try this one which I think is a Klein although McMaster >>>>> doesn't reveal that in their details.

    7289K1 https://www.mcmaster.com/products/7289k1/

    If you call McMaster Carr and ask, they will tell you the brand and
    part/model number.a At least they used to years ago.


    It looks like a Klein 1005 to me, and its only a dollar more than the
    Amazon price so I ordered one. There is also a Harbor Freight Icon that >>> has similar jaws, but also scissor style wire strippers in the back half >>> I plan to look at for $10 less than the Klein's (when on sale) or the
    same price regularly.

    I may take a hand full of scrap wire and cheap terminals with me to the
    Harbor freight store, test it in the parking lot, and return it in
    minutes if it sucks.





    If they turn out to be another POS crimper I'm just going to fucking >>>>> make my own.a I have a drawer full of pliers of various types I almost >>>>> never use, lots of grinding tools, I can always take a shot at hard
    milling, and I have enough 4140 on hand to make a thousand pairs of
    pliers if I can just figure out the best heat treat.


    I got this one:"
    https://www.princessauto.com/en/product/pa0009480492-6-pc-quick-change-ratcheting-crimper/PA0009480492?srsltid=AYCX9vJTdUyuL4VeaeQpHliEiwFy8xsMIbIfeXudmMNOQjQd2qgmXZod.
    Cheap at 3x the price!!!

    I have one almost identical except for the color of the handles.
    (actually a few for different types of termination). All of that style
    I have work great... except on insulated wire terminals. LOL. A light
    pull feels ok, but a firm pull and they come off.
    That is why they are "adjustable". Get the pressure up and they are
    almost as good as welded.
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Jim Wilkins@muratlanne@gmail.com to rec.crafts.metalworking on Tue Nov 10 07:07:43 2026
    From Newsgroup: rec.crafts.metalworking

    "Clare Snyder" wrote in message news:8at4flhvg05ttoaq80i2kc2fui4g865be8@4ax.com...

    That is why they are "adjustable". Get the pressure up and they are
    almost as good as welded.
    -------------------------------

    With large hammer, hydraulic and bolt-cutter-style crimpers I have to pull
    and resistance test the connection to get it right.

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Bob La Londe@none@none.com99 to rec.crafts.metalworking on Thu Nov 12 11:16:07 2026
    From Newsgroup: rec.crafts.metalworking

    On 11/8/2026 11:52 AM, Bob La Londe wrote:

    I decided to try this one which I think is a Klein although McMaster
    doesn't reveal that in their details.

    7289K1 https://www.mcmaster.com/products/7289k1/


    Turned out to be Channelock brand, and to be honest I am very
    unimpressed. They may be a candidate for a prototype grind before
    making my own. This is ridiculous.
    --
    Bob La Londe
    CNC Molds N Stuff
    --- Synchronet 3.22a-Linux NewsLink 1.2