• ali GMAW common practice North America

    From Richard Smith@null@void.com to rec.crafts.metalworking on Tue Jun 23 08:12:49 2026
    From Newsgroup: rec.crafts.metalworking

    Hi there
    Been surprised by what is and is not stocked in the UK.
    What's recommended in the Lincoln "bible" of welding conditions isn't
    doable here it seems due to what's never been heard of.

    For ali boats in the few metres / very few tens of foot range - what are
    the usual techiques?
    You use 5083 Al-Mg for boats?
    In BC, Canada, about 17 years ago I saw push-pull guns in some places and spool-guns in other places. I've only known a conventional GMAW/MIG
    with a "push" feeder used. That isn't the problem with 5000-series as
    I've known - the wire is hard and slippery. Why spool-gun? The boats
    are made from 4000-series?

    Any using 4000-series? (Al-Si)
    Can you push-feed 4043? With larger wire diameters?

    I've only known welding 5083 plate ali, and 6000-series extrusions, with
    5356 (and sometimes higher-strength 5183) welding-wire, with a
    "conventional" push-feed MIG/GMAW welding machine as you would use for
    steel.

    Thanks if anyone can give me some idea on this.



    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Bob La Londe@none@none.com99 to rec.crafts.metalworking on Tue Jun 23 12:14:06 2026
    From Newsgroup: rec.crafts.metalworking

    On 6/23/2026 12:12 AM, Richard Smith wrote:
    Hi there
    Been surprised by what is and is not stocked in the UK.
    What's recommended in the Lincoln "bible" of welding conditions isn't
    doable here it seems due to what's never been heard of.

    For ali boats in the few metres / very few tens of foot range - what are
    the usual techiques?
    You use 5083 Al-Mg for boats?
    In BC, Canada, about 17 years ago I saw push-pull guns in some places and spool-guns in other places. I've only known a conventional GMAW/MIG
    with a "push" feeder used. That isn't the problem with 5000-series as
    I've known - the wire is hard and slippery. Why spool-gun? The boats
    are made from 4000-series?

    Any using 4000-series? (Al-Si)
    Can you push-feed 4043? With larger wire diameters?

    I've only known welding 5083 plate ali, and 6000-series extrusions, with
    5356 (and sometimes higher-strength 5183) welding-wire, with a
    "conventional" push-feed MIG/GMAW welding machine as you would use for
    steel.

    Thanks if anyone can give me some idea on this.


    Most of what I know about welding aluminum I learned from this group,
    the s.e.j.welding group, YouTube videos, and direct experience (very
    small scale hobby level only.) Most of the people who were most versed
    and taught me the most on Usenet are yourself, gunner (deceased), and a
    host of others whom I have not seen on the groups in a long time. I do occasionally ask a question on the Miller welds forum, where there is a
    lot of useful knowledge, but often get no responses or have to wade
    through responses from people trying to look for a reason to show they
    are better than (me).

    I may be the one most likely (and probably least qualified) to respond
    because I have direct interest in aluminum boat building.

    What I was taught is use 5052 for hulls, bulkheads etc, and 5083 or 5086
    for structural, but I think that is mostly for larger watercraft. Not
    modest boats (under 30 feet ~ 10 meters). I was told not to use 6061,
    but it is stronger than 5052, and I was surprised to learn it is
    considered by many to be a marine grade aluminum. Maybe just fresh
    water marine. Do your own research and make your own decisions.

    From a practical standpoint I can buy 5052 sheet and plate in modest quantities as a back yard boat builder from a number of sources, but I
    was not able to find any decent sources for my likely quantities of 5083
    or 5086. I also was able to find some limited marine type extrusions
    suitable for boat construction in 6061. I suspect most domestic small
    craft are all 5052, although companies like Tracker who are big enough
    to have custom extrusions made can get it in whatever alloy they want.

    On to the welding process, 4043 was pretty much frowned upon by
    everybody in marine grade applications. Everybody said just use 5356,
    so that is what I have used for my own aluminum destruction. 5356 seems
    to be a more "universal" wire capable of strong (strong enough) welds in
    6061, 5052, and the stronger 5000 series alloys.

    The actually processes probably vary dramatically from shop to shop
    depending on their size and capitalization.

    At the bottom end is torch rod like Muggy Weld, Alumaweld, and some of
    the Blue Demon products. I have actually made useful parts that are
    still in service using that process. Its slow, tedious, and for those
    reasons I find it very hard to do without burning up stock work pieces.
    Due to the fact that you are melting the welding rod with the heat put
    into the base metal its my opinion its not suitable for anything but
    small jobs. The theory is the torch rod melts at a lower temperature
    than the base metal so you are functionally soldering or "brazing," but
    the reality is the melting temperatures are to close for me to manage
    very well with a torch. I have never heard of anybody using it for more
    than small repairs or making small (relatively) parts.

    At the top end for production speed is probably a push pull system with
    a teflon liner and a pulse MIG power plant. A push pull gun is
    typically smaller than a spool gun, so welding position and access is
    better. Pulse reduces excess heat input and allows a skilled welder to
    make longer welds without using stitch and fill methods.

    I had heard of an AC pulse MIG process for production aluminum welding,
    but when I mentioned it to a local welding instructor he said I was full
    of shit.

    For quality welds AC TIG seems to be the answer being able to break the
    oxide layer with one side of the wave, and weld with the other. Pro
    welders seem to be split about whether or not pulse is necessary. I
    suspect its probably more a function of how they learned to weld, the equipment they have, and that attitude sometimes showing through I
    mentioned about the Miller Welds forum. My personal opinion is that
    pulse TIG may help an amateur hack like myself manage heat input a
    little better, but a highly skilled pro who can feed and travel fast
    with confidence may not need that to make adequate TIG welds in
    aluminum. I have zero success rate TIG welding aluminum, although I do
    have a machine with AC pulse variable balance variable frequency
    capability. My only attempts at TIG aluminum just blew up 6063
    extrusions. My gas hose was probably bad the almost whole time I have
    owned the machine. I have since repairing it made usable if not pretty stainless welds with it. I expect my next attempts to TIG aluminum with
    it might be better if not good.

    In between are guys using a short stinger suitcase welder with a teflon
    liner and a regular push only mig gun to weld aluminum on simple DCEP
    with argon, and guys like myself with a decent DC welder and a spool gun
    who just stitch and fill with lots of cleaning with a stainless wire
    brush in between every weld. The spool gun reduces bird nesting over a
    plain jane MIG stinger. The short stinger regular mig gun gets into the tightest spaces. The key for using a regular MIG gun is keep it very
    short, and keep your cable as straight as possible.

    There are stick aluminum rods out there, but I've never seen any
    information on real commercial use. Just YouTube famous welders showing
    they can burn the stuff.

    If you are going to build boats remember that they break at "hard
    points" and boats flex a lot in use. Aluminum and fiberglass both crack
    and break at hard points. That is where two different pieces,
    structures or sections come together with a sharp corner to concentrate
    force, and sharp is relative. There are a heck of a lot of
    professionally designed, engineered, and built boats out there that have needed to be repaired without being in a wreck. I'm not saying don't
    do it. I am saying build with repair in mind, reinforce your hard
    points, and spread the loads where you can.

    Now that I have exhausted my meager knowledge have a good laugh at my
    expense, and get to work on your project.
    --
    Bob La Londe
    CNC Molds N Stuff
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Richard Smith@null@void.com to rec.crafts.metalworking on Mon Oct 12 08:13:34 2026
    From Newsgroup: rec.crafts.metalworking

    Bob La Londe <none@none.com99> writes:

    On 6/23/2026 12:12 AM, Richard Smith wrote:
    Hi there
    Been surprised by what is and is not stocked in the UK.
    What's recommended in the Lincoln "bible" of welding conditions isn't
    ...

    ...

    In between are guys using a short stinger suitcase welder with a
    teflon liner and a regular push only mig gun to weld aluminum on
    simple DCEP with argon, and guys like myself with a decent DC welder
    and a spool gun who just stitch and fill with lots of cleaning with a stainless wire brush in between every weld. The spool gun reduces
    bird nesting over a plain jane MIG stinger. The short stinger regular
    mig gun gets into the tightest spaces. The key for using a regular
    MIG gun is keep it very short, and keep your cable as straight as
    possible.

    ...

    I will come back on this one from a while ago (mid June).

    Pardon if I asked already.
    Setting the scene for the question:

    Since then I have found - both relating 1.2mm wire vs 1.6mm wire in
    Ali-MIG test-welding on 20mm 5083 plate at about 240A:

    * the torch duty-cycle with 1.6mm wire is much higher than with 1.2mm
    wire - it might be that some useful work could be done with an
    air-cooled torch when using 1.6mm wire

    * the welding machine I got and as it remains now fairly-much manages
    "spray transfer" with the 1.2mm wire but makes a mess with the 1.6mm
    wire

    So question it - those welders with a "suitcase" wire feeder - they had water-cooled torch, or they necessarily went with air-cooled torch?
    They used 1.6mm wire for reason of duty-cycle of the torch?

    Essentially I am trying to cajole the maker of the welding machine into developing a new model which works well in "Constant Voltage".

    I might have asked before, and it might be detail more than you
    observed... sorry if I am trying to go too far.

    Best wishes

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Bob La Londe@none@none.com99 to rec.crafts.metalworking on Mon Oct 12 14:17:42 2026
    From Newsgroup: rec.crafts.metalworking

    On 10/12/2026 12:13 AM, Richard Smith wrote:
    Bob La Londe <none@none.com99> writes:

    On 6/23/2026 12:12 AM, Richard Smith wrote:
    Hi there
    Been surprised by what is and is not stocked in the UK.
    What's recommended in the Lincoln "bible" of welding conditions isn't
    ...

    ...

    In between are guys using a short stinger suitcase welder with a
    teflon liner and a regular push only mig gun to weld aluminum on
    simple DCEP with argon, and guys like myself with a decent DC welder
    and a spool gun who just stitch and fill with lots of cleaning with a
    stainless wire brush in between every weld. The spool gun reduces
    bird nesting over a plain jane MIG stinger. The short stinger regular
    mig gun gets into the tightest spaces. The key for using a regular
    MIG gun is keep it very short, and keep your cable as straight as
    possible.

    ...

    I will come back on this one from a while ago (mid June).

    Pardon if I asked already.
    Setting the scene for the question:

    Since then I have found - both relating 1.2mm wire vs 1.6mm wire in
    Ali-MIG test-welding on 20mm 5083 plate at about 240A:

    * the torch duty-cycle with 1.6mm wire is much higher than with 1.2mm
    wire - it might be that some useful work could be done with an
    air-cooled torch when using 1.6mm wire

    * the welding machine I got and as it remains now fairly-much manages
    "spray transfer" with the 1.2mm wire but makes a mess with the 1.6mm
    wire

    So question it - those welders with a "suitcase" wire feeder - they had water-cooled torch, or they necessarily went with air-cooled torch?
    They used 1.6mm wire for reason of duty-cycle of the torch?

    Essentially I am trying to cajole the maker of the welding machine into developing a new model which works well in "Constant Voltage".

    I might have asked before, and it might be detail more than you
    observed... sorry if I am trying to go too far.

    Best wishes



    I done regurgitated the little bit I think I know. I did re-read my
    previous post to see if if jarred loose any other useful tidbits, but
    alas I have poured it all out and I am now an empty vessel.
    --
    Bob La Londe
    CNC Molds N Stuff
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Snag@Snag_one@msn.com to rec.crafts.metalworking on Mon Oct 12 22:21:57 2026
    From Newsgroup: rec.crafts.metalworking

    On 10/12/2026 4:17 PM, Bob La Londe wrote:
    On 10/12/2026 12:13 AM, Richard Smith wrote:
    Bob La Londe <none@none.com99> writes:

    On 6/23/2026 12:12 AM, Richard Smith wrote:
    Hi there
    Been surprised by what is and is not stocked in the UK.
    What's recommended in the Lincoln "bible" of welding conditions isn't
    ...

    ...

    In between are guys using a short stinger suitcase welder with a
    teflon liner and a regular push only mig gun to weld aluminum on
    simple DCEP with argon, and guys like myself with a decent DC welder
    and a spool gun who just stitch and fill with lots of cleaning with a
    stainless wire brush in between every weld.-a The spool gun reduces
    bird nesting over a plain jane MIG stinger.-a The short stinger regular
    mig gun gets into the tightest spaces.-a The key for using a regular
    MIG gun is keep it very short, and keep your cable as straight as
    possible.

    ...

    I will come back on this one from a while ago (mid June).

    Pardon if I asked already.
    Setting the scene for the question:

    Since then I have found - both relating 1.2mm wire vs 1.6mm wire in
    Ali-MIG test-welding on 20mm 5083 plate at about 240A:

    * the torch duty-cycle with 1.6mm wire is much higher than with 1.2mm
    -a-a wire - it might be that some useful work could be done with an
    -a-a air-cooled torch when using 1.6mm wire

    * the welding machine I got and as it remains now fairly-much manages
    -a-a "spray transfer" with the 1.2mm wire but makes a mess with the 1.6mm
    -a-a wire

    So question it - those welders with a "suitcase" wire feeder - they had
    water-cooled torch, or they necessarily went with air-cooled torch?
    They used 1.6mm wire for reason of duty-cycle of the torch?

    Essentially I am trying to cajole the maker of the welding machine into
    developing a new model which works well in "Constant Voltage".

    I might have asked before, and it might be detail more than you
    observed...-a sorry if I am trying to go too far.

    Best wishes



    I done regurgitated the little bit I think I know.-a I did re-read my previous post to see if if jarred loose any other useful tidbits, but
    alas I have poured it all out and I am now an empty vessel.


    Drink a couple of beers . If nothing else is , your bladder will be
    full . Bob , your posts have on more than one occasion redirected my
    thought processes to a more productive direction .
    --
    Snag
    Muslims hate dogs because they
    protect women , children, and goats .
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Snag@Snag_one@msn.com to rec.crafts.metalworking on Mon Oct 12 22:37:58 2026
    From Newsgroup: rec.crafts.metalworking

    On 10/12/2026 10:21 PM, Snag wrote:
    Bob , your posts have on more than one occasion redirected my
    thought processes to a more productive direction .

    Read that as "you've saved my ass on more than one occasion" .
    --
    Snag
    Muslims hate dogs because they
    protect women , children, and goats .
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Richard Smith@null@void.com to rec.crafts.metalworking on Tue Oct 13 19:51:21 2026
    From Newsgroup: rec.crafts.metalworking

    Bob La Londe <none@none.com99> writes:


    I done regurgitated the little bit I think I know. I did re-read my
    previous post to see if if jarred loose any other useful tidbits, but
    alas I have poured it all out and I am now an empty vessel.

    Appreciated anyway. Best wishes
    --- Synchronet 3.22a-Linux NewsLink 1.2