• Brake cable vs shifter cable?

    From bp@bp@www.zefox.net to rec.bicycles.tech on Mon Nov 9 16:04:34 2026
    From Newsgroup: rec.bicycles.tech

    Is there any difference physically between brake and shifter cable?
    The cable itself looks about the same, the end crimps are obviously
    of different shape, do they differ in strength or construction?

    I substituted a shifter cable for rear brake cable simply because
    it was handy and seemed to fit the brake lever quite well. The lever
    is an old DiaCompe. The little metal "pill" rests nicely in the
    yoke of the lever and doesn't look like it's applying any undue side
    forces that might cause fatigue in the wire strands. The cable itself
    is much stronger than my grip, so I certainly can't damage it.

    Thanks for reading!

    bob prohaska

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From AMuzi@am@yellowjersey.org to rec.bicycles.tech on Mon Nov 9 10:30:56 2026
    From Newsgroup: rec.bicycles.tech

    On 11/9/2026 10:04 AM, bp@www.zefox.net wrote:
    Is there any difference physically between brake and shifter cable?
    The cable itself looks about the same, the end crimps are obviously
    of different shape, do they differ in strength or construction?

    I substituted a shifter cable for rear brake cable simply because
    it was handy and seemed to fit the brake lever quite well. The lever
    is an old DiaCompe. The little metal "pill" rests nicely in the
    yoke of the lever and doesn't look like it's applying any undue side
    forces that might cause fatigue in the wire strands. The cable itself
    is much stronger than my grip, so I certainly can't damage it.

    Thanks for reading!

    bob prohaska

    Probably adequate but brake wires are thicker (more strands)
    of the same material. And since braking forces are much
    greater than shifting forces, the heads are larger as well.
    Do ensure the head cannot pull through your lever's head stop!

    The wires are formed before the head is cast on: https://www.yellowjersey.org/photosfromthepast/cablhead.jpg

    so heads do not readily pull off, but on a gear wire all the
    dimensions are much smaller. Perhaps near the limits of
    what's required. I hope you do find yourself testing that limit!

    For the dollar or two expense of a brake wire, I would
    change it ASAP.
    --
    Andrew Muzi
    am@yellowjersey.org
    Open every day since 1 April, 1971
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Jeff Liebermann@jeffl@cruzio.com to rec.bicycles.tech on Mon Nov 9 09:35:15 2026
    From Newsgroup: rec.bicycles.tech

    On Mon, 9 Nov 2026 16:04:34 -0000 (UTC), bp@www.zefox.net wrote:

    Is there any difference physically between brake and shifter cable?

    The inner wire is different. Brake cables are 1.5 or 1.6mm diameter,
    while gear shifter cables are 1.1 to 1.2mm diameter. There are also differences in the shape and size of the heads (nipples) which are
    designed to prevent you from using the wrong type of cable.

    The cable housings are also different. The brake cable housing is a
    5mm OD spiral design, while the shifter cable housing is a 4mm OD
    longitudinal (straight line) design. The longitudinal shifter housing
    provides a more precise shifting than a coil spring brake design.

    "Bike Brake vs. Shifter Cables - DonAt Mix These Up!" <https://www.youtube.com/watch?v=g6haAYRfa0Y> (4:03)
    --
    Jeff Liebermann jeffl@cruzio.com
    PO Box 272 http://www.LearnByDestroying.com
    Ben Lomond CA 95005-0272 AE6KS 831-336-2558

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From AMuzi@am@yellowjersey.org to rec.bicycles.tech on Mon Nov 9 11:34:14 2026
    From Newsgroup: rec.bicycles.tech

    On 11/9/2026 10:30 AM, AMuzi wrote:
    On 11/9/2026 10:04 AM, bp@www.zefox.net wrote:
    Is there any difference physically between brake and
    shifter cable?
    The cable itself looks about the same, the end crimps are
    obviously
    of different shape, do they differ in strength or
    construction?

    I substituted a shifter cable for rear brake cable simply
    because
    it was handy and seemed to fit the brake lever quite well.
    The lever
    is an old DiaCompe. The little metal "pill" rests nicely
    in the
    yoke of the lever and doesn't look like it's applying any
    undue side
    forces that might cause fatigue in the wire strands. The
    cable itself
    is much stronger than my grip, so I certainly can't damage
    it.

    Thanks for reading!

    bob prohaska

    Probably adequate but brake wires are thicker (more strands)
    of the same material. And since braking forces are much
    greater than shifting forces, the heads are larger as well.
    Do ensure the head cannot pull through your lever's head stop!

    The wires are formed before the head is cast on: https://www.yellowjersey.org/photosfromthepast/cablhead.jpg

    so heads do not readily pull off, but on a gear wire all the
    dimensions are much smaller.-a Perhaps near the limits of
    what's required. I hope you do find yourself testing that
    limit!

    For the dollar or two expense of a brake wire, I would
    change it ASAP.


    oops.
    Should read 'I hope you do _not_...'
    --
    Andrew Muzi
    am@yellowjersey.org
    Open every day since 1 April, 1971
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From bp@bp@www.zefox.net to rec.bicycles.tech on Mon Nov 9 17:39:50 2026
    From Newsgroup: rec.bicycles.tech

    AMuzi <am@yellowjersey.org> wrote:
    On 11/9/2026 10:04 AM, bp@www.zefox.net wrote:
    Is there any difference physically between brake and shifter cable?
    The cable itself looks about the same, the end crimps are obviously
    of different shape, do they differ in strength or construction?

    I substituted a shifter cable for rear brake cable simply because
    it was handy and seemed to fit the brake lever quite well. The lever
    is an old DiaCompe. The little metal "pill" rests nicely in the
    yoke of the lever and doesn't look like it's applying any undue side
    forces that might cause fatigue in the wire strands. The cable itself
    is much stronger than my grip, so I certainly can't damage it.

    Thanks for reading!

    bob prohaska

    Probably adequate but brake wires are thicker (more strands)
    of the same material. And since braking forces are much
    greater than shifting forces, the heads are larger as well.
    Do ensure the head cannot pull through your lever's head stop!

    That seems the most plausible risk, though I don't think it can
    pull through. It's more likely to deform so a proper cable
    won't fit.

    The wires are formed before the head is cast on: https://www.yellowjersey.org/photosfromthepast/cablhead.jpg

    so heads do not readily pull off, but on a gear wire all the
    dimensions are much smaller. Perhaps near the limits of
    what's required. I hope you do find yourself testing that limit!

    For the dollar or two expense of a brake wire, I would
    change it ASAP.

    Thanks for the prompt reply. Next time I'm in the LBS I'll
    get a couple of brake cables. Does anybody offer numbers
    for expected cable failure loads?

    bob prohaska

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From AMuzi@am@yellowjersey.org to rec.bicycles.tech on Mon Nov 9 11:51:32 2026
    From Newsgroup: rec.bicycles.tech

    On 11/9/2026 11:39 AM, bp@www.zefox.net wrote:
    AMuzi <am@yellowjersey.org> wrote:
    On 11/9/2026 10:04 AM, bp@www.zefox.net wrote:
    Is there any difference physically between brake and shifter cable?
    The cable itself looks about the same, the end crimps are obviously
    of different shape, do they differ in strength or construction?

    I substituted a shifter cable for rear brake cable simply because
    it was handy and seemed to fit the brake lever quite well. The lever
    is an old DiaCompe. The little metal "pill" rests nicely in the
    yoke of the lever and doesn't look like it's applying any undue side
    forces that might cause fatigue in the wire strands. The cable itself
    is much stronger than my grip, so I certainly can't damage it.

    Thanks for reading!

    bob prohaska

    Probably adequate but brake wires are thicker (more strands)
    of the same material. And since braking forces are much
    greater than shifting forces, the heads are larger as well.
    Do ensure the head cannot pull through your lever's head stop!

    That seems the most plausible risk, though I don't think it can
    pull through. It's more likely to deform so a proper cable
    won't fit.

    The wires are formed before the head is cast on:
    https://www.yellowjersey.org/photosfromthepast/cablhead.jpg

    so heads do not readily pull off, but on a gear wire all the
    dimensions are much smaller. Perhaps near the limits of
    what's required. I hope you do find yourself testing that limit!

    For the dollar or two expense of a brake wire, I would
    change it ASAP.

    Thanks for the prompt reply. Next time I'm in the LBS I'll
    get a couple of brake cables. Does anybody offer numbers
    for expected cable failure loads?

    bob prohaska


    Depends on your musculature but braking forces are very
    large compared to gear system shift forces:

    https://marathonhandbook.com/average-grip-strength/
    --
    Andrew Muzi
    am@yellowjersey.org
    Open every day since 1 April, 1971
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From AMuzi@am@yellowjersey.org to rec.bicycles.tech on Mon Nov 9 12:07:21 2026
    From Newsgroup: rec.bicycles.tech

    On 11/9/2026 11:39 AM, bp@www.zefox.net wrote:
    AMuzi <am@yellowjersey.org> wrote:
    On 11/9/2026 10:04 AM, bp@www.zefox.net wrote:
    Is there any difference physically between brake and shifter cable?
    The cable itself looks about the same, the end crimps are obviously
    of different shape, do they differ in strength or construction?

    I substituted a shifter cable for rear brake cable simply because
    it was handy and seemed to fit the brake lever quite well. The lever
    is an old DiaCompe. The little metal "pill" rests nicely in the
    yoke of the lever and doesn't look like it's applying any undue side
    forces that might cause fatigue in the wire strands. The cable itself
    is much stronger than my grip, so I certainly can't damage it.

    Thanks for reading!

    bob prohaska

    Probably adequate but brake wires are thicker (more strands)
    of the same material. And since braking forces are much
    greater than shifting forces, the heads are larger as well.
    Do ensure the head cannot pull through your lever's head stop!

    That seems the most plausible risk, though I don't think it can
    pull through. It's more likely to deform so a proper cable
    won't fit.

    The wires are formed before the head is cast on:
    https://www.yellowjersey.org/photosfromthepast/cablhead.jpg

    so heads do not readily pull off, but on a gear wire all the
    dimensions are much smaller. Perhaps near the limits of
    what's required. I hope you do find yourself testing that limit!

    For the dollar or two expense of a brake wire, I would
    change it ASAP.

    Thanks for the prompt reply. Next time I'm in the LBS I'll
    get a couple of brake cables. Does anybody offer numbers
    for expected cable failure loads?

    bob prohaska


    There are a lot of physics papers on bicycle gear rations
    and on spoke tension but couldn't find anything on peak
    tension loads for gear wires.
    --
    Andrew Muzi
    am@yellowjersey.org
    Open every day since 1 April, 1971
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Roger Merriman@roger@sarlet.com to rec.bicycles.tech on Mon Nov 9 18:48:09 2026
    From Newsgroup: rec.bicycles.tech

    AMuzi <am@yellowjersey.org> wrote:
    On 11/9/2026 11:39 AM, bp@www.zefox.net wrote:
    AMuzi <am@yellowjersey.org> wrote:
    On 11/9/2026 10:04 AM, bp@www.zefox.net wrote:
    Is there any difference physically between brake and shifter cable?
    The cable itself looks about the same, the end crimps are obviously
    of different shape, do they differ in strength or construction?

    I substituted a shifter cable for rear brake cable simply because
    it was handy and seemed to fit the brake lever quite well. The lever
    is an old DiaCompe. The little metal "pill" rests nicely in the
    yoke of the lever and doesn't look like it's applying any undue side
    forces that might cause fatigue in the wire strands. The cable itself
    is much stronger than my grip, so I certainly can't damage it.

    Thanks for reading!

    bob prohaska

    Probably adequate but brake wires are thicker (more strands)
    of the same material. And since braking forces are much
    greater than shifting forces, the heads are larger as well.
    Do ensure the head cannot pull through your lever's head stop!

    That seems the most plausible risk, though I don't think it can
    pull through. It's more likely to deform so a proper cable
    won't fit.

    The wires are formed before the head is cast on:
    https://www.yellowjersey.org/photosfromthepast/cablhead.jpg

    so heads do not readily pull off, but on a gear wire all the
    dimensions are much smaller. Perhaps near the limits of
    what's required. I hope you do find yourself testing that limit!

    For the dollar or two expense of a brake wire, I would
    change it ASAP.

    Thanks for the prompt reply. Next time I'm in the LBS I'll
    get a couple of brake cables. Does anybody offer numbers
    for expected cable failure loads?

    bob prohaska


    There are a lot of physics papers on bicycle gear rations
    and on spoke tension but couldn't find anything on peak
    tension loads for gear wires.

    They appear to for some reason last longer than gear cables in terms of not fairly due to becoming sticky which is generally the fate of gear cables in soggy london at least!

    The calliper I find needs cleaning and lubricating but the cable seems
    fine, with the roadie commuter.

    Roger Merriman

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Jeff Liebermann@jeffl@cruzio.com to rec.bicycles.tech on Mon Nov 9 12:13:22 2026
    From Newsgroup: rec.bicycles.tech

    On Mon, 9 Nov 2026 17:39:50 -0000 (UTC), bp@www.zefox.net wrote:

    Does anybody offer numbers
    for expected cable failure loads?

    More on cables:
    <https://www.sheldonbrown.com/cables.html>
    See section on "Cable Failure".

    "Bicycle shifter, brake cable, and housing standards" <https://bike.bikegremlin.com/8548/cable-housing-standards/>
    TL/DR
    "Using brake housing for shifters makes your shifting suck. Using
    shifter housing for brakes is outright dangerous!"

    I'm too lazy/busy to look for the numbers, but my guess(tm) is that
    you'll rip the cable out of the molded zinc cable end before you break
    the cable.

    Andrew is correct. I didn't find much on bicycle consumer web sites.
    I found something in China, but it's for 304 or 316 stainless
    construction cable, not bicycle cables. There might be some numbers
    under "wire rope".

    I'll assume you mean brake cables, which are about 1.5mm OD (1/16in).
    Typical is 1x19 (1 strand, 19 wires) although some premium cables have
    up to 31 strands: <https://www.fairwheelbikes.com/alligator-superior-shine-31-strand-cable.html> For MBL (minimum breaking load) for 1.5mm OD 1x19 is 510 lbs. See
    chart under "breaking strength by diameter": <https://www.qianjun-wire-rope.com/blog/wire-rope-breaking-strength-chart/>

    If you plan on building a hydraulic power assist add-on for a typical
    bicycle braking system, be sure to include a safety factor. For a
    typical dirty and impact prone bicycle environment, I would select a
    safety factor of at least 7:1, which limits the WLL (working load
    limit) to around:
    510 lbs / 7 = 73 lbs
    However, I wouldn't worry too much. You'll probabably rips the wires
    out of the zinc brake cable end, before the cable breaks.
    --
    Jeff Liebermann jeffl@cruzio.com
    PO Box 272 http://www.LearnByDestroying.com
    Ben Lomond CA 95005-0272 AE6KS 831-336-2558

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From zen cycle@funkmasterxx@hotmail.com to rec.bicycles.tech on Tue Nov 10 07:02:30 2026
    From Newsgroup: rec.bicycles.tech

    On 11/9/2026 11:04 AM, bp@www.zefox.net wrote:
    Is there any difference physically between brake and shifter cable?
    The cable itself looks about the same, the end crimps are obviously
    of different shape, do they differ in strength or construction?

    I substituted a shifter cable for rear brake cable simply because
    it was handy and seemed to fit the brake lever quite well. The lever
    is an old DiaCompe. The little metal "pill" rests nicely in the
    yoke of the lever and doesn't look like it's applying any undue side
    forces that might cause fatigue in the wire strands. The cable itself
    is much stronger than my grip, so I certainly can't damage it.

    Thanks for reading!

    bob prohaska


    I've done this before (long ago, before the internet made it easy to get things overnight). The head isn't likely to pull through but you can't
    be too sure about that, given the different tolerances and designs -
    yes, I realize there is a "standard", but that's doesn't guarantee
    anything. I did this once long ago when I knew I wasn't going to be able
    to get to a shop for a while. To mitigate the possibility, I threaded
    the cable through the retainer (or whatever that thing is called), then
    looped it around the retainer and back through, then pulled the cable
    tight enough that the head seemed to seat. Yes, there is enough room in
    the retainer to get two shifter cables through. This reduce the
    possibility of the head pulling through, but also resulted in a very
    spongy brake feel, likely because the cable was never going to be tight
    around the retainer. Fortunately it was for a winter beater that wasn't
    going to see much in the way of hard braking. Still, I replaced when I
    had the chance becasue the brake feel was so soft that I had little
    tactile feedback when wearing heavy winter gloves.

    Take Andrews advice, replace it as soon as you have the opportunity.
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From =?UTF-8?B?Y3ljbGludG9t?=@cyclintom@yahoo.com to rec.bicycles.tech on Tue Nov 10 21:39:52 2026
    From Newsgroup: rec.bicycles.tech

    On Mon Nov 9 17:39:50 2026 bp@www.zefox.net wrote:
    AMuzi <am@yellowjersey.org> wrote:
    On 11/9/2026 10:04 AM, bp@www.zefox.net wrote:
    Is there any difference physically between brake and shifter cable?
    The cable itself looks about the same, the end crimps are obviously
    of different shape, do they differ in strength or construction?

    I substituted a shifter cable for rear brake cable simply because
    it was handy and seemed to fit the brake lever quite well. The lever
    is an old DiaCompe. The little metal "pill" rests nicely in the
    yoke of the lever and doesn't look like it's applying any undue side
    forces that might cause fatigue in the wire strands. The cable itself
    is much stronger than my grip, so I certainly can't damage it.

    Thanks for reading!

    bob prohaska

    Probably adequate but brake wires are thicker (more strands)
    of the same material. And since braking forces are much
    greater than shifting forces, the heads are larger as well.
    Do ensure the head cannot pull through your lever's head stop!

    That seems the most plausible risk, though I don't think it can
    pull through. It's more likely to deform so a proper cable
    won't fit.

    The wires are formed before the head is cast on: https://www.yellowjersey.org/photosfromthepast/cablhead.jpg

    so heads do not readily pull off, but on a gear wire all the
    dimensions are much smaller. Perhaps near the limits of
    what's required. I hope you do find yourself testing that limit!

    For the dollar or two expense of a brake wire, I would
    change it ASAP.

    Thanks for the prompt reply. Next time I'm in the LBS I'll
    get a couple of brake cables. Does anybody offer numbers
    for expected cable failure loads?
    Bob, please replace your cables as soon as possible. the head absolutely Will pull though on hard hraking and the wire itself will fray and brake at the brake lock. you may find it close to impossible to get the head out of the lever without removing the lever and holder. Individual shift wires and brake wires themselves are different diameters.
    --- Synchronet 3.22a-Linux NewsLink 1.2