• =?UTF-8?B?QW5kcmV3?=

    From =?UTF-8?B?Y3ljbGludG9t?=@cyclintom@yahoo.com to rec.bicycles.tech on Mon Oct 26 19:52:26 2026
    From Newsgroup: rec.bicycles.tech

    I don't have access ro a lath and I need a spacer that it 47 mm OD, 41 mm ID and 1 cm deep. Do you have access to tools to be able to make this up for me>
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From AMuzi@am@yellowjersey.org to rec.bicycles.tech on Mon Oct 26 15:37:10 2026
    From Newsgroup: rec.bicycles.tech

    On 10/26/2026 2:52 PM, cyclintom wrote:
    I don't have access ro a lath and I need a spacer that it 47 mm OD, 41 mm ID and 1 cm deep. Do you have access to tools to be able to make this up for me>

    There's no standard part which comes to mind.

    What does this piece do? Is it loaded or can it be plastic?

    Difficult machining job for us as the 1cm depth leaves not
    much to hold.
    --
    Andrew Muzi
    am@yellowjersey.org
    Open every day since 1 April, 1971
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Jeff Liebermann@jeffl@cruzio.com to rec.bicycles.tech on Mon Oct 26 19:55:14 2026
    From Newsgroup: rec.bicycles.tech

    On Mon, 26 Oct 2026 15:37:10 -0500, AMuzi <am@yellowjersey.org> wrote:

    On 10/26/2026 2:52 PM, cyclintom wrote:
    I don't have access ro a lath and I need a spacer that it 47 mm OD, 41 mm ID and 1 cm deep. Do you have access to tools to be able to make this up for me>

    There's no standard part which comes to mind.

    What does this piece do? Is it loaded or can it be plastic?

    Difficult machining job for us as the 1cm depth leaves not
    much to hold.

    Make the first article from plastic using 3D printing or some form of
    casting. After Tom is sure that it's the correct size and that the
    washer works for the intended purpose, think about making it from
    metal might be appropriate. Aluminum would be good for testing.

    IMNHO (in my never humble opinion), turning a 10 mm thick washer held
    in a 3 jaw chuck is not how washers should be made. Start with a
    round bar stock, larger than the required 47 mm OD. Use a 3 jaw chuck
    or if the bar stack is a common OD, use a collet. Turn the OD down to
    the desired 47 mm.

    Next, drill and ream the center hole to the desired 41 mm ID.

    Use a cutoff and parting tool to slice the washers to length. <https://www.google.com/search?udm=2&q=lathe%20parting%20tool>
    Don't try it with a hacksaw. I have a minor scar from that mistake.

    Since Tom is a multi-millionaire, and cost is not an obstacle, having
    the spacers or washers made to order by a machine shop might be an
    alternative. Something like this: <https://www.superiorwasher.com/collections/all-spacers>
    However, if Tom is not a multi-millionaire having an offshore fab shop
    make the washers might be better. Looks JLPCB also does CNC turning: <https://jlccnc.com/cnc-machining-service/cnc-turning> <https://jlccnc.com/help/article/cnc-machining-ordering-guidelines> <https://jlccnc.com/cnc-machining-quote>
    --
    Jeff Liebermann jeffl@cruzio.com
    PO Box 272 http://www.LearnByDestroying.com
    Ben Lomond CA 95005-0272 AE6KS 831-336-2558

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From =?UTF-8?B?Y3ljbGludG9t?=@cyclintom@yahoo.com to rec.bicycles.tech on Tue Oct 27 21:15:45 2026
    From Newsgroup: rec.bicycles.tech

    On Mon Oct 26 15:37:10 2026 AMuzi wrote:
    On 10/26/2026 2:52 PM, cyclintom wrote:
    I don't have access ro a lath and I need a spacer that it 47 mm OD, 41 mm ID and 1 cm deep. Do you have access to tools to be able to make this up for me>

    There's no standard part which comes to mind.

    What does this piece do? Is it loaded or can it be plastic?

    Difficult machining job for us as the 1cm depth leaves not
    much to hold.
    hen I was installing the new press-in bearings into the Colnago C-RS the bearing press I have pushed the left side bearing through and shoved tghe 50 mm fitting in leaving a PF30 sized hole. I guess I will have to take it to a carbon repair shop. This time the 24 mm shaft will be a single steel shaft rather than the titanium Super Record shaft which tilted enough that it stripped the titanium teeth off. I found an aluminum BB rather than plastic.I will ask Robonson if he could repair it and properly install the press in BB. If I had used an aluminum BB in the first place and the 105 crank I don't think that I would have had the problem.
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From AMuzi@am@yellowjersey.org to rec.bicycles.tech on Tue Oct 27 18:17:22 2026
    From Newsgroup: rec.bicycles.tech

    On 10/27/2026 4:15 PM, cyclintom wrote:
    On Mon Oct 26 15:37:10 2026 AMuzi wrote:
    On 10/26/2026 2:52 PM, cyclintom wrote:
    I don't have access ro a lath and I need a spacer that it 47 mm OD, 41 mm ID and 1 cm deep. Do you have access to tools to be able to make this up for me>

    There's no standard part which comes to mind.

    What does this piece do? Is it loaded or can it be plastic?

    Difficult machining job for us as the 1cm depth leaves not
    much to hold.




    hen I was installing the new press-in bearings into the Colnago C-RS the bearing press I have pushed the left side bearing through and shoved tghe 50 mm fitting in leaving a PF30 sized hole. I guess I will have to take it to a carbon repair shop. This time the 24 mm shaft will be a single steel shaft rather than the titanium Super Record shaft which tilted enough that it stripped the titanium teeth off. I found an aluminum BB rather than plastic.I will ask Robonson if he could repair it and properly install the press in BB. If I had used an aluminum BB in the first place and the 105 crank I don't think that I would have had the problem.

    "...I don't think that I would have had the problem."

    Oh, I think you'd find some way to get it to not work.

    Anyone with problems installing a Super Record crank bearing
    has enough creativity for anything.
    --
    Andrew Muzi
    am@yellowjersey.org
    Open every day since 1 April, 1971
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From zen cycle@funkmasterxx@hotmail.com to rec.bicycles.tech on Thu Oct 29 05:16:12 2026
    From Newsgroup: rec.bicycles.tech

    On 10/27/2026 7:17 PM, AMuzi wrote:
    On 10/27/2026 4:15 PM, cyclintom wrote:
    On Mon Oct 26 15:37:10 2026 AMuzi-a wrote:
    On 10/26/2026 2:52 PM, cyclintom wrote:
    I don't have access ro a lath and I need a spacer that it 47 mm OD,
    41 mm ID and 1 cm deep. Do you have access to tools to be able to
    make this up for me>

    There's no standard part which comes to mind.

    What does this piece do? Is it loaded or can it be plastic?

    Difficult machining job for us as the 1cm depth leaves not
    much to hold.




    hen I was installing the new press-in bearings into the Colnago C-RS
    the bearing press I have pushed the left side bearing through and
    shoved tghe 50 mm fitting in leaving a PF30 sized hole. I guess I will
    have to take it to a carbon repair shop. This time the 24 mm shaft
    will be a single steel shaft rather than the titanium Super Record
    shaft which tilted enough that it stripped the titanium teeth off. I
    found an aluminum BB rather than plastic.I will ask Robonson if he
    could repair it and properly install the press in BB. If I had used an
    aluminum BB in the first place and the 105 crank I don't think that I
    would have had the problem.

    "...I don't think that I would have had the problem."

    Oh, I think you'd find some way to get it to not work.

    Anyone with problems installing a Super Record crank bearing has enough creativity for anything.


    I literally laughed out loud...dude, that was funny.
    --- Synchronet 3.22a-Linux NewsLink 1.2