• Look pedal spring tensioning

    From NFN Smith@worldoff9908@gmail.com to rec.bicycles.tech on Wed Oct 21 11:34:02 2026
    From Newsgroup: rec.bicycles.tech

    I have an old set of Look pedals -- these are the first-generation PP66
    that came out in 1985 or 1986, and I've used them more or less
    continuously since I got them used in about 1990. I've been very happy
    with these pedals.

    Something I'm noticing recently is that I'm occasionally pulling out of
    the right pedal if I happen to be cranking hard. The right is the one
    that I normally detach if I'm preparing to put my foot down. No apparent problems with the left.

    Although I may be seeing evidence of a worn cleat, and I'm using the red
    Delta cleat, I'm thinking that there should be a place where I can
    adjust the tension of the spring, but I'm not finding anything. On the
    top of the pedal is a screw, although I think that's there just for
    opening up the pedal body. I had thought that there was an allen socket
    on the side (either 2 or 2.5 mm), but on closer examination, that's just
    the pivot point for snapping in and out.

    Any ideas of where I might find where to adjust the tension? Or is this
    a question for a LBS?

    Smith
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From AMuzi@am@yellowjersey.org to rec.bicycles.tech on Wed Oct 21 14:07:22 2026
    From Newsgroup: rec.bicycles.tech

    On 10/21/2026 1:34 PM, NFN Smith wrote:
    I have an old set of Look pedals -- these are the first-
    generation PP66 that came out in 1985 or 1986, and I've used
    them more or less continuously since I got them used in
    about 1990.-a I've been very happy with these pedals.

    Something I'm noticing recently is that I'm occasionally
    pulling out of the right pedal if I happen to be cranking
    hard. The right is the one that I normally detach if I'm
    preparing to put my foot down. No apparent problems with the
    left.

    Although I may be seeing evidence of a worn cleat, and I'm
    using the red Delta cleat, I'm thinking that there should be
    a place where I can adjust the tension of the spring, but
    I'm not finding anything.-a On the top of the pedal is a
    screw, although I think that's there just for opening up the
    pedal body. I had thought that there was an allen socket on
    the side (either 2 or 2.5 mm), but on closer examination,
    that's just the pivot point for snapping in and out.

    Any ideas of where I might find where to adjust the tension?
    Or is this a question for a LBS?

    Smith

    That series was from before the tension adjuster was added.

    Without regard to that, I'd change the cleats. There's a
    high probability your symptom is merely cleat wear.

    Newer versions of the Delta cleat have a multicolor format
    for a visual wear indicator so one need not guess about that.

    https://biloxibicycleworks.com/cdn/shop/files/Look_Delta_Cleats_9_deg_Studio_1_a5f7dbd6-6491-4c6b-bbc6-e8242887ce84_540x.jpg?v=1712885560
    --
    Andrew Muzi
    am@yellowjersey.org
    Open every day since 1 April, 1971
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From NFN Smith@worldoff9908@gmail.com to rec.bicycles.tech on Sat Oct 24 11:30:20 2026
    From Newsgroup: rec.bicycles.tech

    AMuzi wrote:

    Without regard to that, I'd change the cleats. There's a high
    probability your symptom is merely cleat wear.

    I replaced my cleats, and that fixed my problem, but not for the reason
    I would have expected.

    The plastic from the cleats isn't noticeably worn on the back edge,
    where they interact with the spring. Instead, I hadn't noticed the
    rubber pad in the center of the cleat, and that worn down to where it
    was almost flush with cleat itself.

    I just did a new set of cleats (manufactured by Wellgo, which I know to
    be a reputable manufacturer -- the old cleats were true no-name). I
    would have done the multi-color, if available, but that wasn't an option.

    With the new cleats, they're doing what I want, and a much more audible
    click when I snap in. Ideally, I'd prefer have that click just a little
    bit tighter, but I'm fine with what I have.

    One other thing that I've noticed is that on this set of cleats there is
    a 5 mm Allen screw in the center of the pad. I haven't had time to
    check, but I wonder if this might be a way of adjusting the tension,
    e.g., tightening slightly might make the rubber pad protrude just a
    little more, and as a result, a more snug fit ...?

    Smith

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From zen cycle@funkmasterxx@hotmail.com to rec.bicycles.tech on Mon Oct 26 06:19:22 2026
    From Newsgroup: rec.bicycles.tech

    On 10/24/2026 2:30 PM, NFN Smith wrote:
    AMuzi wrote:

    Without regard to that, I'd change the cleats. There's a high
    probability your symptom is merely cleat wear.

    I replaced my cleats, and that fixed my problem, but not for the reason
    I would have expected.

    The plastic from the cleats isn't noticeably worn on the back edge,
    where they interact with the spring. Instead, I hadn't noticed the
    rubber pad in the center of the cleat, and that worn down to where it
    was almost flush with cleat itself.

    I just did a new set of cleats (manufactured by Wellgo, which I know to
    be a reputable manufacturer -- the old cleats were true no-name). I
    would have done the multi-color, if available, but that wasn't an option.

    With the new cleats, they're doing what I want, and a much more audible click when I snap in. Ideally, I'd prefer have that click just a little
    bit tighter, but I'm fine with what I have.

    One other thing that I've noticed is that on this set of cleats there is
    a 5 mm Allen screw in the center of the pad. I haven't had time to
    check, but I wonder if this might be a way of adjusting the tension,
    e.g., tightening slightly might make the rubber pad protrude just a
    little more, and as a result, a more snug fit ...?

    Smith


    I wouldn't go so far to say Wellgo isn't reputable. They make a fine
    product at discount. I'd call them on par, or slightly better than
    Nashbar. I don't think I have anything from wellgo any more except one
    pair of rat traps, but I still of plenty of nashbar stuff.
    --- Synchronet 3.22a-Linux NewsLink 1.2