• Todays ride new tire

    From Mark J cleary@mcleary08@comcast.net to rec.bicycles.tech on Fri Oct 9 12:05:28 2026
    From Newsgroup: rec.bicycles.tech

    Yesterday I put a new Conti PG5000 32mm tire on the rear 700c wheel of
    the Catrike. The Schwalbe One was a good tire and no flats but when I
    did some checking I could tell getting thin. The new Conti is
    exceptional the best tire you can get really.

    So do today was 43 miles but looked like rain could happen or storm at
    some points so I stayed close to home in case. It did manage bit of rain
    the last 10 miles but no hard just sprinkling constant. I did have to
    get off once and make a small rear derailleur adjustment. I had done
    some work yesterday with indexing and these lever bar shifters are ok
    but finicky to get perfect. I ended up just backing off tension of the
    cable about 1/2 turn and then all was fine.

    I think that is my problem. When I go to set the indexing in the big
    front and small rear I always just overshoot the target. It will shift
    fine but I want it fast and quick so I think I just put a bit more
    tension on the cable. This works fine on the stand but in practice you
    need a bit of relaxing to make sure it does not overshoot the cog. It
    will fall in place and work but just not square. I was glad to get that ok.

    My chain is stretched 1/16 of inch in 12 links but with long drive train
    and 3 chains equivalent I think I still good for maybe 1000-1200 miles.
    --
    Deacon Mark

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From AMuzi@am@yellowjersey.org to rec.bicycles.tech on Fri Oct 9 12:30:12 2026
    From Newsgroup: rec.bicycles.tech

    On 10/9/2026 12:05 PM, Mark J cleary wrote:
    Yesterday I put a new Conti PG5000 32mm tire on the rear
    700c wheel of the Catrike. The Schwalbe One was a good tire
    and no flats but when I did some checking I could tell
    getting thin. The new Conti is exceptional the best tire you
    can get really.

    So do today was 43 miles but looked like rain could happen
    or storm at some points so I stayed close to home in case.
    It did manage bit of rain the last 10 miles but no hard just
    sprinkling constant. I did have to get off once and make a
    small rear derailleur adjustment. I had done some work
    yesterday with indexing and these lever bar shifters are ok
    but finicky to get perfect. I ended up just backing off
    tension of the cable about 1/2 turn and then all was fine.

    I think that is my problem. When I go to set the indexing in
    the big front and small rear I always just overshoot the
    target. It will shift fine but I want it fast and quick so I
    think I just put a bit more tension on the cable. This works
    fine on the stand but in practice you need a bit of relaxing
    to make sure it does not overshoot the cog. It will fall in
    place and work but just not square. I was glad to get that ok.

    My chain is stretched 1/16 of inch in 12 links but with long
    drive train and 3 chains equivalent I think I still good for
    maybe 1000-1200 miles.

    Regarding "make sure it does not overshoot the cog", get in
    the habit of checking your low gear adjustment firmly with
    your thumb like this:

    https://www.yellowjersey.org/photosfromthepast/gearchek.jpg

    and don't rely only on the shifter/gear wire. Details in
    purple text box here:

    https://www.yellowjersey.org/endweld.html
    --
    Andrew Muzi
    am@yellowjersey.org
    Open every day since 1 April, 1971
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Mark J cleary@mcleary08@comcast.net to rec.bicycles.tech on Fri Oct 9 13:49:39 2026
    From Newsgroup: rec.bicycles.tech

    On 10/9/2026 12:30 PM, AMuzi wrote:
    On 10/9/2026 12:05 PM, Mark J cleary wrote:
    Yesterday I put a new Conti PG5000 32mm tire on the rear 700c wheel of
    the Catrike. The Schwalbe One was a good tire and no flats but when I
    did some checking I could tell getting thin. The new Conti is
    exceptional the best tire you can get really.

    So do today was 43 miles but looked like rain could happen or storm at
    some points so I stayed close to home in case. It did manage bit of
    rain the last 10 miles but no hard just sprinkling constant. I did
    have to get off once and make a small rear derailleur adjustment. I
    had done some work yesterday with indexing and these lever bar
    shifters are ok but finicky to get perfect. I ended up just backing
    off tension of the cable about 1/2 turn and then all was fine.

    I think that is my problem. When I go to set the indexing in the big
    front and small rear I always just overshoot the target. It will shift
    fine but I want it fast and quick so I think I just put a bit more
    tension on the cable. This works fine on the stand but in practice you
    need a bit of relaxing to make sure it does not overshoot the cog. It
    will fall in place and work but just not square. I was glad to get
    that ok.

    My chain is stretched 1/16 of inch in 12 links but with long drive
    train and 3 chains equivalent I think I still good for maybe 1000-1200
    miles.

    Regarding "make sure it does not overshoot the cog", get in the habit of checking your low gear adjustment firmly with your thumb like this:

    https://www.yellowjersey.org/photosfromthepast/gearchek.jpg

    and don't rely only on the shifter/gear wire. Details in purple text box here:

    https://www.yellowjersey.org/endweld.html


    I assume you then mean to adjust the limit screw if the chain goes off
    the biggest cog? Obviously it is set to high but if you back of the
    barrel adjuster this will also fix that issue too right? Granted though
    you need to get limit set not to over throw the cog if you force too hard.
    --
    Deacon Mark
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From AMuzi@am@yellowjersey.org to rec.bicycles.tech on Fri Oct 9 14:13:02 2026
    From Newsgroup: rec.bicycles.tech

    On 10/9/2026 1:49 PM, Mark J cleary wrote:
    On 10/9/2026 12:30 PM, AMuzi wrote:
    On 10/9/2026 12:05 PM, Mark J cleary wrote:
    Yesterday I put a new Conti PG5000 32mm tire on the rear
    700c wheel of the Catrike. The Schwalbe One was a good
    tire and no flats but when I did some checking I could
    tell getting thin. The new Conti is exceptional the best
    tire you can get really.

    So do today was 43 miles but looked like rain could
    happen or storm at some points so I stayed close to home
    in case. It did manage bit of rain the last 10 miles but
    no hard just sprinkling constant. I did have to get off
    once and make a small rear derailleur adjustment. I had
    done some work yesterday with indexing and these lever
    bar shifters are ok but finicky to get perfect. I ended
    up just backing off tension of the cable about 1/2 turn
    and then all was fine.

    I think that is my problem. When I go to set the indexing
    in the big front and small rear I always just overshoot
    the target. It will shift fine but I want it fast and
    quick so I think I just put a bit more tension on the
    cable. This works fine on the stand but in practice you
    need a bit of relaxing to make sure it does not overshoot
    the cog. It will fall in place and work but just not
    square. I was glad to get that ok.

    My chain is stretched 1/16 of inch in 12 links but with
    long drive train and 3 chains equivalent I think I still
    good for maybe 1000-1200 miles.

    Regarding "make sure it does not overshoot the cog", get
    in the habit of checking your low gear adjustment firmly
    with your thumb like this:

    https://www.yellowjersey.org/photosfromthepast/gearchek.jpg

    and don't rely only on the shifter/gear wire. Details in
    purple text box here:

    https://www.yellowjersey.org/endweld.html


    I assume you then mean to adjust the limit screw if the
    chain goes off the biggest cog? Obviously it is set to high
    but if you back of the barrel adjuster this will also fix
    that issue too right? Granted though you need to get limit
    set not to over throw the cog if you force too hard.


    If I understand you, that's right.
    Do not rely on the shifter and gear wire tension. Ensure the
    changer's stop screw will absolutely not allow overshift.
    --
    Andrew Muzi
    am@yellowjersey.org
    Open every day since 1 April, 1971
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Roger Merriman@roger@sarlet.com to rec.bicycles.tech on Fri Oct 9 21:20:18 2026
    From Newsgroup: rec.bicycles.tech

    Mark J cleary <mcleary08@comcast.net> wrote:
    Yesterday I put a new Conti PG5000 32mm tire on the rear 700c wheel of
    the Catrike. The Schwalbe One was a good tire and no flats but when I
    did some checking I could tell getting thin. The new Conti is
    exceptional the best tire you can get really.

    ItrCOs a very popular tyre as was its predecessor, this said the Schwalbe One is a range of road tyres with the more basic tyres for training or
    commuting or ones just for commuters such as the One plus that I have,
    which is the roadie Marathon plus, to One pro? Or similar name that is a
    direct competitor to the GP5000 where as the more basic One is more like
    the super sport? That I think Conti make?

    So do today was 43 miles but looked like rain could happen or storm at
    some points so I stayed close to home in case. It did manage bit of rain
    the last 10 miles but no hard just sprinkling constant. I did have to
    get off once and make a small rear derailleur adjustment. I had done
    some work yesterday with indexing and these lever bar shifters are ok
    but finicky to get perfect. I ended up just backing off tension of the
    cable about 1/2 turn and then all was fine.

    I think that is my problem. When I go to set the indexing in the big
    front and small rear I always just overshoot the target. It will shift
    fine but I want it fast and quick so I think I just put a bit more
    tension on the cable. This works fine on the stand but in practice you
    need a bit of relaxing to make sure it does not overshoot the cog. It
    will fall in place and work but just not square. I was glad to get that ok.

    My chain is stretched 1/16 of inch in 12 links but with long drive train
    and 3 chains equivalent I think I still good for maybe 1000-1200 miles.

    I tend to replace when the chain/cassette is worn/stretched and shifting
    starts to get sluggish as the ramps and whatnot have worn down.

    So 2/3 thousand depending on the bike.

    Roger Merriman

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From zen cycle@funkmasterxx@hotmail.com to rec.bicycles.tech on Sat Oct 10 07:52:05 2026
    From Newsgroup: rec.bicycles.tech

    On 10/9/2026 1:05 PM, Mark J cleary wrote:
    Yesterday I put a new Conti PG5000 32mm tire on the rear 700c wheel of
    the Catrike. The Schwalbe One was a good tire and no flats but when I
    did some checking I could tell getting thin. The new Conti is
    exceptional the best tire you can get really.

    See my post on wheels and tires - it tracks with your experience.


    So do today was 43 miles but looked like rain could happen or storm at
    some points so I stayed close to home in case. It did manage bit of rain
    the last 10 miles but no hard just sprinkling constant. I did have to
    get off once and make a small rear derailleur adjustment. I had done
    some work yesterday with indexing and these lever bar shifters are ok
    but finicky to get perfect. I ended up just backing off tension of the
    cable about 1/2 turn and then all was fine.

    I think that is my problem. When I go to set the indexing in the big
    front and small rear I always just overshoot the target. It will shift
    fine but I want it fast and quick so I think I just put a bit more
    tension on the cable. This works fine on the stand but in practice you
    need a bit of relaxing to make sure it does not overshoot the cog. It
    will fall in place and work but just not square. I was glad to get that ok.

    Rely on the derailleur limit screw for that, not the barrel adjuster.
    Yes, you _can_ use the barrel adjuster as a limit adjustment, but it
    isn't made for that, will need constant retweaking, and will affect the shifting over the rest of the cog. Get the system to shift into the
    largest and smallest cog, set the limit screws, then work on the cable
    tension for shift performance from there.

    My chain is stretched 1/16 of inch in 12 links but with long drive train
    and 3 chains equivalent I think I still good for maybe 1000-1200 miles.

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Catrike Ryder@Soloman@old.bikers.org to rec.bicycles.tech on Sat Oct 10 12:36:53 2026
    From Newsgroup: rec.bicycles.tech

    On Fri, 9 Oct 2026 12:30:12 -0500, AMuzi <am@yellowjersey.org> wrote:

    On 10/9/2026 12:05 PM, Mark J cleary wrote:
    Yesterday I put a new Conti PG5000 32mm tire on the rear
    700c wheel of the Catrike. The Schwalbe One was a good tire
    and no flats but when I did some checking I could tell
    getting thin. The new Conti is exceptional the best tire you
    can get really.

    So do today was 43 miles but looked like rain could happen
    or storm at some points so I stayed close to home in case.
    It did manage bit of rain the last 10 miles but no hard just
    sprinkling constant. I did have to get off once and make a
    small rear derailleur adjustment. I had done some work
    yesterday with indexing and these lever bar shifters are ok
    but finicky to get perfect. I ended up just backing off
    tension of the cable about 1/2 turn and then all was fine.

    I think that is my problem. When I go to set the indexing in
    the big front and small rear I always just overshoot the
    target. It will shift fine but I want it fast and quick so I
    think I just put a bit more tension on the cable. This works
    fine on the stand but in practice you need a bit of relaxing
    to make sure it does not overshoot the cog. It will fall in
    place and work but just not square. I was glad to get that ok.

    My chain is stretched 1/16 of inch in 12 links but with long
    drive train and 3 chains equivalent I think I still good for
    maybe 1000-1200 miles.

    Regarding "make sure it does not overshoot the cog", get in
    the habit of checking your low gear adjustment firmly with
    your thumb like this:

    https://www.yellowjersey.org/photosfromthepast/gearchek.jpg

    and don't rely only on the shifter/gear wire. Details in
    purple text box here:

    https://www.yellowjersey.org/endweld.html

    Going back through this thread made me realize that although I set the
    limits on the new Deore derailleur when it was new, that was four
    years ago and since then I've gone through three different hubs and
    cassettes. I've got it shifting really smooth, but could it be pushed
    off into the chain?

    Turns out, yes it could...

    A problem was that it's totally impossible to crank the pedals on the
    Catrike while pressing on the derailleur. Instead of cranking, I
    simply pulled on the chain and got the same nasty results. It took a
    half turn on the low limit to fix it, and it still shifts down to the
    big gear as nicely as before.

    --
    C'est bon
    Soloman
    --- Synchronet 3.22a-Linux NewsLink 1.2