My Cannon Pixma MG6150 All-In-One has just died on me, I'll have a poke around it but there's probably nothing I can do.
What are the recommendations for a replacement nowadays? I only print
black and white so a laser might be worth considering. Are there any that
don't 'phone home or insist you change the cartridge very 5 minutes?
Do more scanning than printing, wired network connection preferred, it's never failed me before today.
My Cannon Pixma MG6150 All-In-One has just died on me, I'll have a poke around it but there's probably nothing I can do.
What are the recommendations for a replacement nowadays? I only print
black and white so a laser might be worth considering. Are there any that don't 'phone home or insist you change the cartridge very 5 minutes?
Do more scanning than printing, wired network connection preferred, it's never failed me before today.
My Cannon Pixma MG6150 All-In-One has just died on me, I'll have a poke around it but there's probably nothing I can do.
What are the recommendations for a replacement nowadays? I only print
black and white so a laser might be worth considering. Are there any
that don't 'phone home or insist you change the cartridge very 5 minutes?
Do more scanning than printing, wired network connection preferred, it's never failed me before today.
My Cannon Pixma MG6150 All-In-One has just died on me, I'll have a poke around it but there's probably nothing I can do.
What are the recommendations for a replacement nowadays? I only print
black and white so a laser might be worth considering. Are there any that don't 'phone home or insist you change the cartridge very 5 minutes?
Do more scanning than printing, wired network connection preferred, it's never failed me before today.
Lasers generally produce clearer output, which certainly is better stuck
to the paper, and are sometimes less fussy about what they print on (I
run mine mostly on junk mail, which is often only printed on one side,
for anything I don't intend to keep forever).
On that basis, the machines worth looking at are all Brother mono lasers, >because Brother is the last big vendor whose toner carts are a plastic
hopper with a fill plug and a mechanical reset gear rather than a chip and
an e-fuse. HP and Samsung went to chips years ago, which is why they are
the wrong answer for this problem set, in my humblest of opinions.
On Sun, 15 Nov 2026 15:29:25 -0400, Maria Sophia <mariasophia@comprehension.com> wrote:
On that basis, the machines worth looking at are all Brother mono lasers,
because Brother is the last big vendor whose toner carts are a plastic
hopper with a fill plug and a mechanical reset gear rather than a chip and >> an e-fuse. HP and Samsung went to chips years ago, which is why they are
the wrong answer for this problem set, in my humblest of opinions.
I have a Brother HL-1210W which has just stopped working.
When I bought it the major advantage was that the ink cartridge was
separate from the roller. It said that the ink cartridge could do 1000
pages, and the roller 10000.
For some time now it has been warning me that the roller needs
replacing, but I haven't noticed any decrease in print quality, so
I've put off replacing it.
But now when I switch it on, it makes a clicking sound, but doesn't
run its startup routine, and then a red ligh flashes. Sometimes
seitching it on and off at the wall plug got it to start up properly,
but now it mostly doesn't.
Is this something the could be fixed by getting a new roller? I'm
pretty sure it would cost more than getting a new printer, but I'm
reluctant to get a new printer because it might be one of the "phone
home" models, and also might not have drivers for my Windows XP and
Windows 10 32-bit printers.
On Sun, 15 Nov 2026 15:29:25 -0400, Maria Sophia <mariasophia@comprehension.com> wrote:
On that basis, the machines worth looking at are all Brother mono lasers,
because Brother is the last big vendor whose toner carts are a plastic
hopper with a fill plug and a mechanical reset gear rather than a chip and >> an e-fuse. HP and Samsung went to chips years ago, which is why they are
the wrong answer for this problem set, in my humblest of opinions.
I have a Brother HL-1210W which has just stopped working.
When I bought it the major advantage was that the ink cartridge was
separate from the roller. It said that the ink cartridge could do 1000
pages, and the roller 10000.
For some time now it has been warning me that the roller needs
replacing, but I haven't noticed any decrease in print quality, so
I've put off replacing it.
But now when I switch it on, it makes a clicking sound, but doesn't
run its startup routine, and then a red ligh flashes. Sometimes
seitching it on and off at the wall plug got it to start up properly,
but now it mostly doesn't.
Is this something the could be fixed by getting a new roller? I'm
pretty sure it would cost more than getting a new printer, but I'm
reluctant to get a new printer because it might be one of the "phone
home" models, and also might not have drivers for my Windows XP and
Windows 10 32-bit printers.
Check the cartridge number before buying the machine, not after.
Brother's newer high-yield carts do carry chips, and some firmware updates >have started refusing third-party ones. The pre-chip TN-750/TN-830 family
is the safe target.
On 2026/11/15 11:12:56, Jeff Gaines wrote:
My Cannon Pixma MG6150 All-In-One has just died on me, I'll have a poke
around it but there's probably nothing I can do.
What are the recommendations for a replacement nowadays? I only print
black and white so a laser might be worth considering. Are there any that
I'd say definitely go for a laser; certainly if you don't do a _lot_ of printing, as ink printers tend to dry out (blocking the heads; for some brands such as HP [some models] the head is part of the ink cartridge,
so not disastrous but expensive; for other makes such as EPSON it isn't. Xerox used to make models where the tanks fitted into a carrier
[including the heads] that was also easily replaceable, but I doubt they still do). They also tend to go through a "cleaning cycle" whenever
powered on - or, sometimes, once a day anyway - which uses up ink even
if you aren't doing any printing; laser printers don't _do_ that.
On 15/11/2026 in message <11dd16k$bpa$1@nnrp.usenet.blueworldhosting.com> >Maria Sophia wrote:
[snipped but read]
Check the cartridge number before buying the machine, not after.
Brother's newer high-yield carts do carry chips, and some firmware updates >>have started refusing third-party ones. The pre-chip TN-750/TN-830 family >>is the safe target.
Many thanks for that very detailed response Maria :-)
Many of those Brothers seem to be obsolete now but I will look at the >current range for something suitable.
On 2026-11-15 14:28, J. P. Gilliver wrote:
I'd say definitely go for a laser; certainly if you don't do a _lot_ of
printing, as ink printers tend to dry out (blocking the heads; for some
brands such as HP [some models] the head is part of the ink cartridge,
so not disastrous but expensive; for other makes such as EPSON it isn't.
Xerox used to make models where the tanks fitted into a carrier
[including the heads] that was also easily replaceable, but I doubt they
still do). They also tend to go through a "cleaning cycle" whenever
powered on - or, sometimes, once a day anyway - which uses up ink even
if you aren't doing any printing; laser printers don't _do_ that.
+1
A consideration, specially for second hand: the rubber rollers do age.
My laser printer was bought Aug 2008, and I have to replace it because
it can no longer grab "heavy" paper: it works with 80 grams paper, but
not 110 grams.
Otherwise, it is still working fine.
I looked a bit at what HP has available, and I am inclined for not all
in one. Print in colour, double side, and scan automatically a pile of paper, autofeed, double side.
On 11/15/2026 18:42, Steve Hayes wrote:
I have a Brother HL-1210W which has just stopped working.
When I bought it the major advantage was that the ink cartridge was
separate from the roller. It said that the ink cartridge could do 1000
pages, and the roller 10000.
For some time now it has been warning me that the roller needs
replacing, but I haven't noticed any decrease in print quality, so
I've put off replacing it.
But now when I switch it on, it makes a clicking sound, but doesn't
run its startup routine, and then a red ligh flashes. Sometimes
seitching it on and off at the wall plug got it to start up properly,
but now it mostly doesn't.
Is this something the could be fixed by getting a new roller? I'm
pretty sure it would cost more than getting a new printer, but I'm
reluctant to get a new printer because it might be one of the "phone
home" models, and also might not have drivers for my Windows XP and
Windows 10 32-bit printers.
Not only is the HL-1210W discontinued,, the consumables (toner and
drums) are apparently discontinued as well. So you have to buy a new >printer. You must have had it for at least 10 years, so do not feel bad >about it.
I have an HL-2320-D which is working OK. I had to replace the drum once. There is a WiFi model also. With WiFi, it costs $125 at Walmart. Without
WiFi it costs $320 at Amazon according to Google search results. These
do two-sided printing (D for Duplex).
| Sysop: | Amessyroom |
|---|---|
| Location: | Fayetteville, NC |
| Users: | 76 |
| Nodes: | 6 (0 / 6) |
| Uptime: | 55:40:49 |
| Calls: | 1,265 |
| Calls today: | 1 |
| Files: | 1,362 |
| D/L today: |
3 files (2,684K bytes) |
| Messages: | 285,687 |