• WiFi speed question

    From Graham J@nobody@nowhere.co.uk to alt.comp.os.windows-11 on Fri Nov 6 17:46:28 2026
    From Newsgroup: alt.comp.os.windows-11

    FTTP with nominally 100/20 performance

    Vigor 2860 router. Wifi settings are:

    Mode = 11b+g+n (Mixed)
    Security mode = Mixed(WPA+WPA2)/PSK
    WPA Encryption Mode: = TKIP for WPA/AES for WPA2

    Use speedtest.net

    PC connected by Ethernet reports 106 Mbits/sec down; 20 Mbits set up, so performance is as expected.

    Old iPad Air 2 : model A1567 via WiFi reports 75 Mbits/sec down; 20
    Mbits/sec up, which is probably reasonable.

    Brand new Dell DC16256 laptop arrived today, just powered up and
    installed all Microsoft updates. WiFi reports 15 Mbits/sec down and 12 Mbits/sec up. Sometimes a little better, maybe 25/20. NIC is:
    Realtek 8852CE WiFi 6E PCI-E

    Laptop tested several times, when there is no other network traffic running.

    Laptop is in same room as router, about 2 metres away from it.

    Any ideas why the new laptop performance is so poor?
    --
    Graham J
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Johann 'Myrkraverk' Oskarsson@johann@myrkraverk.invalid to alt.comp.os.windows-11 on Sat Nov 7 02:08:39 2026
    From Newsgroup: alt.comp.os.windows-11

    On 11/7/2026 1:46 AM, Graham J wrote:
    FTTP with nominally 100/20 performance

    Vigor 2860 router.-a Wifi settings are:

    Mode-a-a-a-a-a-a-a-a-a-a-a = 11b+g+n (Mixed)
    Security mode-a-a-a-a-a-a-a = Mixed(WPA+WPA2)/PSK
    WPA Encryption Mode:-a-a-a = TKIP for WPA/AES for WPA2

    Use speedtest.net

    PC connected by Ethernet reports 106 Mbits/sec down; 20 Mbits set up, so performance is as expected.

    Old iPad Air 2 : model A1567 via WiFi reports 75 Mbits/sec down; 20 Mbits/sec up, which is probably reasonable.

    Brand new Dell DC16256 laptop arrived today, just powered up and
    installed all Microsoft updates.-a WiFi reports 15 Mbits/sec down and 12 Mbits/sec up.-a Sometimes a little better, maybe 25/20.-a NIC is:
    Realtek 8852CE WiFi 6E PCI-E

    Laptop tested several times, when there is no other network traffic
    running.

    Laptop is in same room as router, about 2 metres away from it.

    Any ideas why the new laptop performance is so poor?



    Idea yes, proof no. Wifi can be slow due to interference by other wifi signals. If that's happening, I'm not sure moving it closer will help.

    Of course it can be the hardware being slow, driver being bad, and so
    forth. Even a bad wifi antenna in the laptop.

    If you have one on hand, or have the budget, a USB wifi dongle might
    have a stronger signal. But I /dislike/ suggesting things that re-
    quire a budget, so you can table that discussion.

    Something to try that doesn't require a budget, is a Linux USB drive
    that you boot into a /live distro/ and test if the speed is the same.
    That of course doesn't require a budget only if you have the USB drive
    to play with.


    Best wishes, and I hope you figure it out.
    --
    Johann | email: invalid -> com | http://www.myrkraverk.com/blog/
    I'm not from the Internet, I just work there. | via Easynews.com https://bsky.app/profile/myrkraverk.bsky.social | for ( ;; ) _:;
    Federated at https://fed.brid.gy/bsky/myrkraverk.bsky.social
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Andy Burns@usenet@andyburns.uk to alt.comp.os.windows-11 on Fri Nov 6 18:42:20 2026
    From Newsgroup: alt.comp.os.windows-11

    Graham J wrote:

    Any ideas why the new laptop performance is so poor?
    Shouldn't be necessary ... but realtek, so ...

    can you limit the adapter to wifi4 speeds to match your router?

    Is your router set for 20 or 40MHz channels? alter adapter to suit

    Try disabling any low power modes


    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From knuttle@keith_nuttle@yahoo.com to alt.comp.os.windows-11 on Fri Nov 6 14:02:39 2026
    From Newsgroup: alt.comp.os.windows-11

    On 11/06/2026 12:46 PM, Graham J wrote:
    FTTP with nominally 100/20 performance

    Vigor 2860 router.-a Wifi settings are:

    Mode-a-a-a-a-a-a-a-a-a-a-a = 11b+g+n (Mixed)
    Security mode-a-a-a-a-a-a-a = Mixed(WPA+WPA2)/PSK
    WPA Encryption Mode:-a-a-a = TKIP for WPA/AES for WPA2

    Use speedtest.net

    PC connected by Ethernet reports 106 Mbits/sec down; 20 Mbits set up, so performance is as expected.

    Old iPad Air 2 : model A1567 via WiFi reports 75 Mbits/sec down; 20 Mbits/sec up, which is probably reasonable.

    Brand new Dell DC16256 laptop arrived today, just powered up and
    installed all Microsoft updates.-a WiFi reports 15 Mbits/sec down and 12 Mbits/sec up.-a Sometimes a little better, maybe 25/20.-a NIC is:
    Realtek 8852CE WiFi 6E PCI-E

    Laptop tested several times, when there is no other network traffic
    running.

    Laptop is in same room as router, about 2 metres away from it.

    Any ideas why the new laptop performance is so poor?


    From your question is sounds like you have multiple device accessing
    the internet. Here are some things I do when the internet is slower
    than I expect:

    Some times the router at the ISP gets over loaded or damaged. By
    rebooting your breaking the IPS connection waiting a few seconds and
    relog on, forces your connection to a different ISP router.

    Rebooting you own router.

    Some time your own router will become slow, because to many are connect
    to it. There maybe several overlooked devices accessing the router like
    TV's printers' garmins, cars, etc. On my router I can clear this
    situation with the Clear Rescan function from the router control webpage Usually accessed using the the router web ID number 197.168.08.xxxx

    Make sure the Router parameter are set correctly, and in computer.

    Make sure the MS has not set some foolish security fleeter that is
    interfering with the connection.
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Paul@nospam@needed.invalid to alt.comp.os.windows-11 on Fri Nov 6 14:15:44 2026
    From Newsgroup: alt.comp.os.windows-11

    On Fri, 11/6/2026 12:46 PM, Graham J wrote:
    FTTP with nominally 100/20 performance

    Vigor 2860 router.-a Wifi settings are:

    Mode-a-a-a-a-a-a-a-a-a-a-a = 11b+g+n (Mixed)
    Security mode-a-a-a-a-a-a-a = Mixed(WPA+WPA2)/PSK
    WPA Encryption Mode:-a-a-a = TKIP for WPA/AES for WPA2

    Use speedtest.net

    PC connected by Ethernet reports 106 Mbits/sec down; 20 Mbits set up, so performance is as expected.

    Old iPad Air 2 : model A1567 via WiFi reports 75 Mbits/sec down; 20 Mbits/sec up, which is probably reasonable.

    Brand new Dell DC16256 laptop arrived today, just powered up and installed all Microsoft updates.-a WiFi reports 15 Mbits/sec down and 12 Mbits/sec up.-a Sometimes a little better, maybe 25/20.-a NIC is:
    Realtek 8852CE WiFi 6E PCI-E

    Laptop tested several times, when there is no other network traffic running.

    Laptop is in same room as router, about 2 metres away from it.

    Any ideas why the new laptop performance is so poor?



    https://www.itpro.com/wifi-hotspots/31078/draytek-vigor-2860ac-review

    "DrayTek has always valued reliability over keeping up with cutting-edge
    network standards and that's reflected in the Vigor 2860AC. Despite the high price,
    it's only a 3x3 stream 802.11ac router offering speeds of up to 1,300Mbits/sec over 5GHz
    and 300Mbits/sec over 2.4GHz.

    Wireless performance isn't great either. In our tests we saw a
    top speed of 54.8MB/sec over 5GHz in the throughput test at close range,
    which isn't bad, but in the long range test the Vigor 2860AC fell flat,
    achieving only 1.64MB/sec over 5GHz. That's just about enough to stream
    Netflix in 1080p but not much else, and its 2.4GHz performance was worse.
    "

    I would suggest reviewing whether you should be using 5GHz only,
    or allowing it to just do whatever it wants (run over 2.4GHz and
    it is likely running in 2x2 MIMO there).

    You start with the claimed best-operating-mode (1,300Mbits/sec), then immediately cut that in half (as no Wifi negotiates full rate), giving 650Mbit/sec which is roughly 80MB/sec. Now compare that to the
    benchmark-above value of 54.8MB/sec. That's pretty good. Your laptop
    has two antennas, and running 2x2 on your end, take 0.66 of
    those kinds of numbers, to get some idea of the potential.
    650*0.66 = 429Mbit/sec or 50MB/sec best case, so expect to "meet"
    your broadband spec while using the 5Ghz band.

    On 2.4GHz, a USB3 cable can emit a broadband interference
    centered on 2.5GHz. Whereas on 5GHz, that's a null for the USB3
    interference. The 5GHz band does not penetrate walls well,
    or pass through a metallic doorway at all, but within the
    room, you're more likely to get the download rate of your
    broadband, on the laptop.

    On the old website where they tested wireless routers (gone now),
    they discovered that some situations in the lab, an "absorbing mat"
    placed in the lab setup, to reduce signal level, actually
    improved goodput. More and more signal is not always the
    best thing, because it can be a multipath issue. One of the
    purposes of MIMO, is to better handle multipath (each antenna
    twisted slightly different than the others). The radios on
    Wifi kit, are supposed to turn down their level, when they
    detect the close-proximity kit is receiving enough signal.

    For indicators, there are two to consider. There is
    the raw signal level (1 to 5 bars maybe). There is also
    a Quality indicator, which could be viewed as Goodput. You can
    have situations where the signal level is five bars, the quality
    is one bar, and that's signal bouncing off walls (multipath)
    and the signal is too strong. You can also have situations where
    the signal level is one bar, and the quality is five bars, indicating
    "it is doing the best it can with what it got". A few pieces of electronics view their job in this way, signal level and quality metric.

    Summary: Retest at 5GHz, assuming all devices can be operated that way.
    Some dual-band devices "make poor life choices" when it comes
    to band selection, and for such devices, you jam them to
    a single band.

    Paul

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Daniel70@daniel47@nomail.afraid.org to alt.comp.os.windows-11 on Sat Nov 7 20:00:59 2026
    From Newsgroup: alt.comp.os.windows-11

    On 7/11/2026 5:08 am, Johann 'Myrkraverk' Oskarsson wrote:
    On 11/7/2026 1:46 AM, Graham J wrote:
    FTTP with nominally 100/20 performance

    Vigor 2860 router.-a Wifi settings are:

    Mode-a-a-a-a-a-a-a-a-a-a-a = 11b+g+n (Mixed)
    Security mode-a-a-a-a-a-a-a = Mixed(WPA+WPA2)/PSK
    WPA Encryption Mode:-a-a-a = TKIP for WPA/AES for WPA2

    Use speedtest.net

    PC connected by Ethernet reports 106 Mbits/sec down; 20 Mbits set up,
    so performance is as expected.

    Old iPad Air 2 : model A1567 via WiFi reports 75 Mbits/sec down; 20
    Mbits/sec up, which is probably reasonable.

    Brand new Dell DC16256 laptop arrived today, just powered up and
    installed all Microsoft updates.-a WiFi reports 15 Mbits/sec down and
    12 Mbits/sec up.-a Sometimes a little better, maybe 25/20.-a NIC is:
    Realtek 8852CE WiFi 6E PCI-E

    Laptop tested several times, when there is no other network traffic
    running.

    Laptop is in same room as router, about 2 metres away from it.

    Any ideas why the new laptop performance is so poor?

    Idea yes, proof no.-a Wifi can be slow due to interference by other wifi signals.-a If that's happening, I'm not sure moving it closer will help.

    Of course it can be the hardware being slow, driver being bad, and so forth.-a Even a bad wifi antenna in the laptop.

    If you have one on hand, or have the budget, a USB wifi dongle might
    have a stronger signal.-a But I /dislike/ suggesting things that re-
    quire a budget, so you can table that discussion.

    Something to try that doesn't require a budget, is a Linux USB drive
    that you boot into a /live distro/ and test if the speed is the same.
    That of course doesn't require a budget only if you have the USB drive
    to play with.

    .... and the (limited?) knowledge of how to install/use Linux

    Best wishes, and I hope you figure it out.

    Ditto!!
    --
    Daniel70
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Johann 'Myrkraverk' Oskarsson@johann@myrkraverk.invalid to alt.comp.os.windows-11 on Sat Nov 7 17:31:24 2026
    From Newsgroup: alt.comp.os.windows-11

    On 11/7/2026 5:00 PM, Daniel70 wrote:
    On 7/11/2026 5:08 am, Johann 'Myrkraverk' Oskarsson wrote:
    On 11/7/2026 1:46 AM, Graham J wrote:
    FTTP with nominally 100/20 performance

    Vigor 2860 router.-a Wifi settings are:

    Mode-a-a-a-a-a-a-a-a-a-a-a = 11b+g+n (Mixed)
    Security mode-a-a-a-a-a-a-a = Mixed(WPA+WPA2)/PSK
    WPA Encryption Mode:-a-a-a = TKIP for WPA/AES for WPA2

    Use speedtest.net

    PC connected by Ethernet reports 106 Mbits/sec down; 20 Mbits set up,
    so performance is as expected.

    Old iPad Air 2 : model A1567 via WiFi reports 75 Mbits/sec down; 20
    Mbits/sec up, which is probably reasonable.

    Brand new Dell DC16256 laptop arrived today, just powered up and
    installed all Microsoft updates.-a WiFi reports 15 Mbits/sec down and
    12 Mbits/sec up.-a Sometimes a little better, maybe 25/20.-a NIC is:
    Realtek 8852CE WiFi 6E PCI-E

    Laptop tested several times, when there is no other network traffic
    running.

    Laptop is in same room as router, about 2 metres away from it.

    Any ideas why the new laptop performance is so poor?

    Idea yes, proof no.-a Wifi can be slow due to interference by other wifi
    signals.-a If that's happening, I'm not sure moving it closer will help.

    Of course it can be the hardware being slow, driver being bad, and so
    forth.-a Even a bad wifi antenna in the laptop.

    If you have one on hand, or have the budget, a USB wifi dongle might
    have a stronger signal.-a But I /dislike/ suggesting things that re-
    quire a budget, so you can table that discussion.

    Something to try that doesn't require a budget, is a Linux USB drive
    that you boot into a /live distro/ and test if the speed is the same.
    That of course doesn't require a budget only if you have the USB drive
    to play with.

    .... and the (limited?) knowledge of how to install/use Linux


    Sure. Not everyone wants to do this test when figuring out hardware
    issues. What you need to know is: there are distros that are /live/ or
    come in /live/ packages. This means you can boot up the Linux distro,
    open a browser, and perform the speed test -- almost no Linux knowledge necessary -- without installing anything on the hard disk.

    It used to be called a /live disk/ back when these were distributed as
    CD-ROMS or DVDs. Nowadays, you download the ISO image, and boot it via
    Ventoy or something, on a USB stick.

    I have also used Ventoy to boot Windows 10 installation media, when I
    didn't have a second Microsoft computer to create the bootable USB stick
    with the offical Microsoft tools. So if nothing else, people here
    should know that tool exists [1].

    And I think that's enough of esoteric emergency installion knowledge for alt.comp.os.windows-11. Hopefully none of you ever need it.


    Best wishes, and happy Windows!

    [1] Until it doesn't but by then, hopefully some other tool has replaced
    it.
    --
    Johann | email: invalid -> com | http://www.myrkraverk.com/blog/
    I'm not from the Internet, I just work there. | via Easynews.com https://bsky.app/profile/myrkraverk.bsky.social | for ( ;; ) _:;
    Federated at https://fed.brid.gy/bsky/myrkraverk.bsky.social
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Paul@nospam@needed.invalid to alt.comp.os.windows-11 on Sat Nov 7 05:34:06 2026
    From Newsgroup: alt.comp.os.windows-11

    On Sat, 11/7/2026 4:31 AM, Johann 'Myrkraverk' Oskarsson wrote:
    On 11/7/2026 5:00 PM, Daniel70 wrote:
    On 7/11/2026 5:08 am, Johann 'Myrkraverk' Oskarsson wrote:
    On 11/7/2026 1:46 AM, Graham J wrote:
    FTTP with nominally 100/20 performance

    Vigor 2860 router.-a Wifi settings are:

    Mode-a-a-a-a-a-a-a-a-a-a-a = 11b+g+n (Mixed)
    Security mode-a-a-a-a-a-a-a = Mixed(WPA+WPA2)/PSK
    WPA Encryption Mode:-a-a-a = TKIP for WPA/AES for WPA2

    Use speedtest.net

    PC connected by Ethernet reports 106 Mbits/sec down; 20 Mbits set up, so performance is as expected.

    Old iPad Air 2 : model A1567 via WiFi reports 75 Mbits/sec down; 20 Mbits/sec up, which is probably reasonable.

    Brand new Dell DC16256 laptop arrived today, just powered up and installed all Microsoft updates.-a WiFi reports 15 Mbits/sec down and 12 Mbits/sec up.-a Sometimes a little better, maybe 25/20.-a NIC is:
    Realtek 8852CE WiFi 6E PCI-E

    Laptop tested several times, when there is no other network traffic running.

    Laptop is in same room as router, about 2 metres away from it.

    Any ideas why the new laptop performance is so poor?

    Idea yes, proof no.-a Wifi can be slow due to interference by other wifi >>> signals.-a If that's happening, I'm not sure moving it closer will help. >>>
    Of course it can be the hardware being slow, driver being bad, and so
    forth.-a Even a bad wifi antenna in the laptop.

    If you have one on hand, or have the budget, a USB wifi dongle might
    have a stronger signal.-a But I /dislike/ suggesting things that re-
    quire a budget, so you can table that discussion.

    Something to try that doesn't require a budget, is a Linux USB drive
    that you boot into a /live distro/ and test if the speed is the same.
    That of course doesn't require a budget only if you have the USB drive
    to play with.

    .... and the (limited?) knowledge of how to install/use Linux


    Sure.-a Not everyone wants to do this test when figuring out hardware issues.-a What you need to know is: there are distros that are /live/ or
    come in /live/ packages.-a This means you can boot up the Linux distro,
    open a browser, and perform the speed test -- almost no Linux knowledge necessary -- without installing anything on the hard disk.

    It used to be called a /live disk/ back when these were distributed as CD-ROMS or DVDs.-a Nowadays, you download the ISO image, and boot it via Ventoy or something, on a USB stick.

    I have also used Ventoy to boot Windows 10 installation media, when I
    didn't have a second Microsoft computer to create the bootable USB stick
    with the offical Microsoft tools.-a So if nothing else, people here
    should know that tool exists [1].

    And I think that's enough of esoteric emergency installion knowledge for alt.comp.os.windows-11.-a Hopefully none of you ever need it.


    Best wishes, and happy Windows!

    [1] Until it doesn't but by then, hopefully some other tool has replaced
    it.

    I tried a Google on the part number, and it might actually
    be a trouble-maker.

    https://www.reddit.com/r/linux4noobs/comments/1ipe3zn/wifi_8852ce_realtek_woes_on_moving_to_linux/

    Some of the RealTek ones, it took a year or so before a driver was
    available.

    And even when there is a driver, it might still be in need of "tuning"
    so it isn't entirely "ripe". Like maybe the band selection logic isn't
    perfect yet.

    Wifi are country-sensitive, and during driver install time,
    the "band plan" has to match the country you are in. When I install a Wifi
    in Canada, the driver uses the plan for Canada and not the plan for the U.K.
    As otherwise, you could be illegally operating your device (as if anyone cares).
    Maybe the U.K. has Channel 14 and Canada does not. I'm sure any splatter
    in that part of the band, is cheerfully ignored, as there is so much of it
    (a U.K. person moves to Canada and brings their router with them, being
    an example scenario).

    On Broadcom Wifi, there are too many Linux drivers, and you need a
    genius to help you blacklist the ones you should not use. Most
    distros know how to do that now, and we don't need helpers for that.
    But at one time, you could have trouble with that (wrong driver binding).

    On some laptops (high end), the BIOS will only accept branded
    Intel Wifi modules. Attempts to substitute a MediaTek won't
    work with those, as the BIOS will not map the module and it cannot
    be seen by an OS. The odds of that happening today, are 1% or lower.
    That was an Intel marketing scheme that required "Intel purity"
    that was monitored by the BIOS design.

    For the most part, the Wifi socket is so interchangeable, the
    factory has a box of MediaTek sitting next to a box of Intel AX
    modules, a person just reaches into a box and pulls one out and
    shoves it in. By multi-sourcing, the production line does not
    stop when one of the boxes is empty. And people might tell you
    "on that laptop, you could get a Mediatek or an Intel". which means
    the BOM cost for the modules was so close, there is no preference
    during assembly. It's just whatever box is sitting there, provides
    a module.

    There are two kinds of Intel modules. You have to select the
    type that is "independent of the computer details", all of the
    hardware it needs is inside the module. The other type needs
    something that is inside an Intel chipset, so there will be
    situations where buying one of those is a mistake. It might
    be something like AX200 is OK, AX201 is not, that sort of thing.

    Wifi may require a bit of research and Googling, at the best of times,
    so you can't be in a rush when buying stuff (like, a replacement module).

    *******

    I recommend starting, by playing with the available controls, to coax
    a bit more performance from the thing. Then, if you've given up
    hope, you can look further down the debug chart, for some additional
    desperate things to try. And replacement is always an option.
    There's only so much frustration you can put up with on these things.
    Sure, booting to Linux is great, but not if the hardware in question
    happens to be a pest with a reputation.

    When dealing with Wifi, I don't expect a good time. There are other
    kinds of hardware that are much better in terms of average experience
    with them.

    And if you have got a refurb laptop from somewhere, you should
    check the Wifi antenna connections are seated on the module, as
    some user may have messed with them and nobody checked. Don't
    take those apart, unless you absolutely have to, as the connector
    is "squashy" and you can ruin it with your thumb. When you take
    it off, you may find it doesn't want to go back on again (compression
    fit). I've had a few reports from people who tell me they ruined
    the connector while trying to fit it.

    Paul
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Anssi Saari@anssi.saari@usenet.mail.kapsi.fi to alt.comp.os.windows-11 on Sat Nov 7 18:47:15 2026
    From Newsgroup: alt.comp.os.windows-11

    Graham J <nobody@nowhere.co.uk> writes:

    Any ideas why the new laptop performance is so poor?

    I recently noticed I had managed to configure my laptop to use 802.11g
    only, somehow, I'm really not sure how that happened. But that resulted
    in low speeds like yours.

    The settings were somewhat contradictory anyways and there's a bunch of
    them.
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Brian Gregory@void-invalid-dead-dontuse@email.invalid to alt.comp.os.windows-11 on Sat Nov 7 19:53:15 2026
    From Newsgroup: alt.comp.os.windows-11

    On 06/11/2026 18:08, Johann 'Myrkraverk' Oskarsson wrote:
    Idea yes, proof no.-a Wifi can be slow due to interference by other wifi signals.-a If that's happening, I'm not sure moving it closer will help.

    It can help by making the signal to noise ratio better.
    But I guess it is possible that it won't help if the interference is
    strong. You could still be having to use only the gaps in the
    interference for your data.
    --
    Brian Gregory (in England).
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Paul@nospam@needed.invalid to alt.comp.os.windows-11 on Sat Nov 7 16:27:07 2026
    From Newsgroup: alt.comp.os.windows-11

    On Sat, 11/7/2026 2:53 PM, Brian Gregory wrote:
    On 06/11/2026 18:08, Johann 'Myrkraverk' Oskarsson wrote:
    Idea yes, proof no.-a Wifi can be slow due to interference by other wifi
    signals.-a If that's happening, I'm not sure moving it closer will help.

    It can help by making the signal to noise ratio better.
    But I guess it is possible that it won't help if the interference is strong. You could still be having to use only the gaps in the interference for your data.

    It's just as likely to be strong signal reflections and multipath,
    as it is to be "microwave oven leakage" style interference.

    The web site that used to test and characterize Wifi routers
    (now shut down as a site), the person there discovered by
    placing RF absorbing mats in the lab environment, they
    were able to get more goodput through the Wifi they were
    testing. Sometimes, too much signal is the problem (as it
    raises more and more multipath component). And
    Wifi do apparently have the ability to adjust transmit
    power as a function of responses seen. Typically your
    Wifi is not running at the unlicensed-limit.

    Some USB3 cabling to hard drive enclosures, was emitting
    broadband ("computer-data based") spectra centered at 2.5GHz,
    with zeros at DC and 5GHz. Intel wrote a white paper on that.
    That can cause wireless keyboards and wireless mice to stop
    working, even when they use spread-spectrum methods. That should
    not be happening today particularly.

    It's because of the zero at 5GHz, you can suggest to a person
    they try the 5GHz Wifi band. The wireless keyboard and wireless mouse,
    only communicate on 2.4GHz and have no option for that. While
    the Wifi does have band options. A Wifi can "escape" from USB3
    interference, while the HID devices are generally stuck on
    2.4GHz. And the HID devices are allowed to use a different
    modulation scheme if they want. Some HID were using AM on
    the CB band for a while, as an example of how clever some of
    it was years ago. Most of the activity today on the products,
    is more consistent, with only one style of modulation being
    used and just the one band. Even when a product is not
    Bluetooth compatible, it can still be using a "Bluetooth-like"
    method. But it won't pair with Bluetooth (necessarily).

    *******

    You can use something like this, if you want to examine what is
    in the airwaves around you. The front end on these goes out
    to 6GHz.

    https://greatscottgadgets.com/hackrf/one/

    There was talk of blocking the importation of these, because
    car thieves were using them as a means of hacking car doors.
    I don't know what the supply situation is like on those today.
    Some SDR are receive only, others have a transmit capability as well.
    This is presumably why car thieves like it.

    "HackRF OnerCOs maximum TX power varies by operating frequency:

    1 MHz to 10 MHz: 5 dBm to 15 dBm, generally increasing as frequency increases (see this blog post)
    10 MHz to 2170 MHz: 5 dBm to 15 dBm, generally decreasing as frequency increases
    2170 MHz to 2740 MHz: 13 dBm to 15 dBm
    2740 MHz to 4000 MHz: 0 dBm to 5 dBm, decreasing as frequency increases
    4000 MHz to 6000 MHz: -10 dBm to 0 dBm, generally decreasing as frequency increases

    Most people will just be using the receive side.

    "Hacking the Airwaves: Detect WiFi & Bluetooth Devices Using HackRF"
    [Live signal frequency spectra visible at 12 minutes in]

    https://www.youtube.com/watch?v=1SkK7cQ02Lc

    Because Wifi transmissions are short in the time domain,
    there is not a continuous spectra present with time.

    There are other SDR available which are cheaper, but
    neither the sampling bandwidth nor the range of front
    end frequencies, are suitable on those for Wifi.

    If you had microwave oven leakage as an interference,
    that would show up in the raw signal trace, as a "bump"
    that stands there continuously, instead of just flashing
    past as the Wifi is doing.

    Paul

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Graham J@nobody@nowhere.co.uk to alt.comp.os.windows-11 on Mon Nov 9 12:58:32 2026
    From Newsgroup: alt.comp.os.windows-11

    Anssi Saari wrote:
    Graham J <nobody@nowhere.co.uk> writes:

    Any ideas why the new laptop performance is so poor?

    OP here.

    Dell DC16256 laptop is brand new delivered 6/11/2026. Realtek driver is
    dated 28/04/2026, version 6001.16.175.0 - can't find anything newer on web.

    Interference: laptop and iPad used for comparison are on the same table,
    so in the same interference environment. iPad is consistently 75
    Mbits/sec down; 20 Mbits/sec up; laptop about 15 Mbits/sec down and 12 Mbits/sec up although it varies a little, sometime achieving 20
    Mbits/sec down. The slower speeds are measured at times when the
    internet might be congested - which confuses me, since the WiFi is
    clearly the limiting factor.

    Router only offers 2.4GHz band so using 5GHz isn't possible.

    Band configuration is normally 11b/g/n. 11n-only fails, 11g-only gives similar speeds.

    Channel width was 20 MHz, doubling to 40MHz made no improvement.

    Moving laptop away from router to another room to reduce signal strength
    made no different.

    The Realtek has no settings for low power operation.

    I plan to order a USB to Ethernet adapter so I don't have to use WiFi.

    Would be interested to hear other people's experience with the Realtek
    8852CE WiFi 6E PCI-E NIC.
    --
    Graham J
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Paul@nospam@needed.invalid to alt.comp.os.windows-11 on Mon Nov 9 08:47:45 2026
    From Newsgroup: alt.comp.os.windows-11

    On Mon, 11/9/2026 7:58 AM, Graham J wrote:
    Anssi Saari wrote:
    Graham J <nobody@nowhere.co.uk> writes:

    Any ideas why the new laptop performance is so poor?

    OP here.

    Dell DC16256 laptop is brand new delivered 6/11/2026.-a Realtek driver is dated 28/04/2026, version 6001.16.175.0 - can't find anything newer on web.

    Interference: laptop and iPad used for comparison are on the same table, so in the same interference environment.-a iPad is consistently 75 Mbits/sec down; 20 Mbits/sec up; laptop about 15 Mbits/sec down and 12 Mbits/sec up although it varies a little, sometime achieving 20 Mbits/sec down.-a The slower speeds are measured at times when the internet might be congested - which confuses me, since the WiFi is clearly the limiting factor.

    Router only offers 2.4GHz band so using 5GHz isn't possible.

    Band configuration is normally 11b/g/n.-a 11n-only fails, 11g-only gives similar speeds.

    Channel width was 20 MHz, doubling to 40MHz made no improvement.

    Moving laptop away from router to another room to reduce signal strength -amade no different.

    The Realtek has no settings for low power operation.

    I plan to order a USB to Ethernet adapter so I don't have to use WiFi.

    Would be interested to hear other people's experience with the Realtek 8852CE WiFi 6E PCI-E NIC.



    There is something you can try adjusting here. Presumably this is in Device Manager,
    in the properties page of the device.

    https://superuser.com/questions/1870147/slow-wifi-download-speeds-in-windows-when-using-realtek-8852ce-wifi-nic-while-th

    "(For 8852CE) Changing Roaming Sensitivity Level from Middle to Disabled fixed internet issues in my case."

    *******

    As for the Ethernet, you might want to check what the ports on the router are. They could be 100BT or GbE for example. The USB to Ethernet adapters, the
    chip is made by ASIX. There are two types. The older one is 100BT,
    the newer one is 1GBE. The 1GBE can run at multiple speeds, so is flexible.

    My setup is like this, with the unmanaged switch providing good speed within the room. Whereas the modem router were picked to match my lousy broadband speed.
    The stuff on the left of the picture, is slower than the stuff on the right. The stuff on the right does not degrade my broadband speed. This means I can transfer files within the room at 280MB/sec currently (between some machines), whereas the broadband by comparison is a joke. The ASIX is 112MB/sec on file shares.

    one-speed second-speed
    modem-router ---------------- 8 port switch ----- 1 <=== plug an ASIX in here --- USB --- desktop computer
    ----- 2
    ...
    ----- 8

    Paul

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Graham J@nobody@nowhere.co.uk to alt.comp.os.windows-11 on Mon Nov 9 15:18:03 2026
    From Newsgroup: alt.comp.os.windows-11

    Paul wrote:

    [snip]

    There is something you can try adjusting here. Presumably this is in Device Manager,
    in the properties page of the device.

    https://superuser.com/questions/1870147/slow-wifi-download-speeds-in-windows-when-using-realtek-8852ce-wifi-nic-while-th

    "(For 8852CE) Changing Roaming Sensitivity Level from Middle to Disabled fixed internet issues in my case."

    [snip]

    Tried "Roaming Aggressiveness" was level 4= medium. Changed to level 1
    = disabled. No improvement.

    Tried "PCI Express - Link State Power Management". Set both to OFF. No improvement.
    --
    Graham J
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Graham J@nobody@nowhere.co.uk to alt.comp.os.windows-11 on Mon Nov 9 18:27:37 2026
    From Newsgroup: alt.comp.os.windows-11

    Graham J wrote:
    Anssi Saari wrote:
    Graham J <nobody@nowhere.co.uk> writes:

    Any ideas why the new laptop performance is so poor?

    OP here.

    Dell DC16256 laptop is brand new delivered 6/11/2026.-a Realtek driver is dated 28/04/2026, version 6001.16.175.0 - can't find anything newer on web.

    Interference: laptop and iPad used for comparison are on the same table,
    so in the same interference environment.-a iPad is consistently 75
    Mbits/sec down; 20 Mbits/sec up; laptop about 15 Mbits/sec down and 12 Mbits/sec up although it varies a little, sometime achieving 20
    Mbits/sec down.-a The slower speeds are measured at times when the
    internet might be congested - which confuses me, since the WiFi is
    clearly the limiting factor.

    Router only offers 2.4GHz band so using 5GHz isn't possible.

    [snip]

    OP here.

    Set laptop to use 2.4GH band only, to ensure it won't try to use 5GHz.

    Tried a different router: the FRITZ!Box 7530. Speed measures 94
    Mbits/sec down; 19 Mbits/sec up - so about as good as I could expect.

    The only difference I can see is that the Vigor 2860 router security is "Mixed(WPA+WPA2)/PSK" whereas the FRITZ!Box 7530 is "WPA2/WPA3".

    Clearly Mixed(WPA+WPA2)/PSK does not impair the speed of the iPad, so
    why does it affect the laptop with the Realtek 8852CE NIC ???

    The Realtek shows the connection to the Vigor is "WPA-2 Personal".

    Ideas please?
    --
    Graham J
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Andy Burns@usenet@andyburns.uk to alt.comp.os.windows-11 on Mon Nov 9 18:42:38 2026
    From Newsgroup: alt.comp.os.windows-11

    Graham J wrote:

    The only difference I can see is that the Vigor 2860 router security is "Mixed(WPA+WPA2)/PSK" whereas the FRITZ!Box 7530 is "WPA2/WPA3".

    Clearly Mixed(WPA+WPA2)/PSK does not impair the speed of the iPad, so
    why does it affect the laptop with the Realtek 8852CE NIC ???

    The Realtek shows the connection to the Vigor is "WPA-2 Personal".

    Ideas please?

    Security settings shouldn't affect connection speed ...

    is fritz using same channel that vigor was?

    long/short guard interval?
    long/short preamble

    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Graham J@nobody@nowhere.co.uk to alt.comp.os.windows-11 on Mon Nov 9 18:56:16 2026
    From Newsgroup: alt.comp.os.windows-11

    Andy Burns wrote:
    Graham J wrote:

    The only difference I can see is that the Vigor 2860 router security
    is "Mixed(WPA+WPA2)/PSK" whereas the FRITZ!Box 7530 is "WPA2/WPA3".

    Clearly Mixed(WPA+WPA2)/PSK does not impair the speed of the iPad, so
    why does it affect the laptop with the Realtek 8852CE NIC ???

    The Realtek shows the connection to the Vigor is "WPA-2 Personal".

    Ideas please?

    Security settings shouldn't affect connection speed ...

    But apparently it does. Just tested:

    Vigor 2860 set to Mixed(WPA+WPA2)/PSK is slow.

    Vigor 2860 set to WPA2/PSK is much faster at about 94Mbits/sec down;
    19 Mbits/sec up. iPad not affected by this change, continues to be fast.

    Google suggests it is a bug in the NIC, see:

    <https://www.google.com/search?q=Realtek+8852CE+slowed+by+wpa-2+personal&oq=Realtek+8852CE+slowed+by+wpa-2+personal&aqs=chrome..69i57j0i751l4j0i546i649.11146j0j7&sourceid=chrome&ie=UTF-8>
    --
    Graham J
    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Andy Burns@usenet@andyburns.uk to alt.comp.os.windows-11 on Mon Nov 9 19:04:29 2026
    From Newsgroup: alt.comp.os.windows-11

    Graham J wrote:

    Vigor 2860 set to Mixed(WPA+WPA2)/PSK is slow.

    Vigor 2860 set to WPA2/PSK is much faster
    WPA1 is truly ancient, if you don't have any devices that need it, stick
    with WPA2 only, or mixed WPA2/WPA3 if the router supports it.


    --- Synchronet 3.22a-Linux NewsLink 1.2
  • From Paul@nospam@needed.invalid to alt.comp.os.windows-11 on Mon Nov 9 14:39:37 2026
    From Newsgroup: alt.comp.os.windows-11

    On Mon, 11/9/2026 1:56 PM, Graham J wrote:
    Andy Burns wrote:
    Graham J wrote:

    The only difference I can see is that the Vigor 2860 router security is "Mixed(WPA+WPA2)/PSK" whereas the FRITZ!Box 7530 is "WPA2/WPA3".

    Clearly Mixed(WPA+WPA2)/PSK does not impair the speed of the iPad, so why does it affect the laptop with the Realtek 8852CE NIC ???

    The Realtek shows the connection to the Vigor is "WPA-2 Personal".

    Ideas please?

    Security settings shouldn't affect connection speed ...

    But apparently it does.-a Just tested:

    Vigor 2860 set to Mixed(WPA+WPA2)/PSK is slow.

    Vigor 2860 set to WPA2/PSK is much faster at about 94Mbits/sec down;
    19 Mbits/sec up.-a iPad not affected by this change, continues to be fast.

    Google suggests it is a bug in the NIC, see:

    <https://www.google.com/search?q=Realtek+8852CE+slowed+by+wpa-2+personal&oq=Realtek+8852CE+slowed+by+wpa-2+personal&aqs=chrome..69i57j0i751l4j0i546i649.11146j0j7&sourceid=chrome&ie=UTF-8>



    And one of the hits from your Google search, indicates other
    hardware combinations are affected by "mixed" security setting.
    Maybe it's not entirely a device level issue, but the concept
    is a bit off-target.

    Paul
    --- Synchronet 3.22a-Linux NewsLink 1.2